AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and Plastic Plate User Manual

June 12, 2024
AUDLES

Cover, product description
Rechargeable Submersible LED Light with magnets and plastic plate [containing iron sheet) Put the main picture of the product

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate -

Product Introduction

Premiun ABS shell (Reliable and compression resistant) ON/OFF button (Long press until the light lights up or off) 16LEDs (Brighter/larger)
Product front view

Type-C charging port
Charging: indicator light on red Fully charged (411): indicator light is green
Contain magnet
(Attach to metal-bearing surface) Notch (Connection stuck point) Contain iron sheet (Connection magnet)
Stuck point (Connection notch) Lattice texture (Place to apply glue)
Product back view

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig2

 How to Use

  1. Choose a smooth and flat surface, wipe off dirt, dust. Spread the glue EVENLY on the grid (Paste more firmly)
    Tile drawing
    AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig3

  2. Apply a quarter (about 0.1702) from the glue pipe to the plate (the side with lattice texture) Suggested application method:Apply three parallel glue lines
    Glue application diagram
    AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig4

  3. Glue the plate to the surface

  4. Press for at least 90 seconds, then wait at least 1 hour, the glue solidifies and It’s not easy to move the plate (The glue cures completely after 12 hours)
    Press iron sheet diagram
    AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig5

  5. Aim the light at the four stuck points on the plate and stick It to the
    plate Lighting diagram
    AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig6

Component Supplement

  1. Charging port
    Note: Please keep the charging port clean and dry. Be sure that the waterproof silicone cover is close putting the pool light in the water.

Charging diagram

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig7

2. Magnet
There are four magnets in the center of the bottom of the light, which can be attached to the metal surface. Clean the surface before attaching Attach magnet
Magnetic attraction diagram

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets
and Plastic Plate - fig8
3. Plastic plate

Plastic plate (containing iron sheet) can be used for walls or floors with smooth/rough/uneven gaps, etc. Smooth RoughUneven pans
Schematic diagram of plastic plate

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig9

4. Glue
Tips:

  • Storein a cool and dry place away frornlight.

  • After opening, please use It as soon as possible,

  • Not edible. Please stay away from food and children.
    ” At water temperatures of 78-83 F, glue cuissier at least 1 hour. .
    When stored unopened below 77 F, the shelf life of the product is 2 years.
    The plate coated with glue is exposed to the air:
    If the glue has not yet solidified, it can be used with new glue; if the glue has solidified, it cannot be used and needs to be cleaned with a spatula. (Cured glue is easily removed with a spatula, even glue that has been cured for a long time is easy to clean)

  • Preventive treatment:
    Glue is environmentally friendly, insoluble in water, and has RoHS certification. When used under prescribed safety measures, it is usually harmless. However, some people with skin allergies may be affected, so we recommend that they wear impermeable rubber gloves or plastic gloves and protective glasses when using glue. After use, wash the skin thoroughly with soap and warm water, avoiding solvents. Dry your skin with disposable paper towels instead of towel.

5. Remote control Turn off Timer Turn on &Check Timer Brightness+Brightness-6 Dynamic modes (FLASH1/2, FADE1/2, SMOOTH1/2) On the basis of mode 1, press again to switch to mode 2 Small light
Remote control schematic

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets
and Plastic Plate - fig10

Function:

  • Steady colors: 16;

    • Color changing: Yes;
    • Frequency:434.02MHz;
    •  Flash 1: Red, green, blue (3 kinds of colors of cycle);
    • Flash 2: Red, yellow, green, cyan, blue, purple, white (7 kinds of colors of cycle);
    • Fade 1: Red, green, blue (3 kinds of colors of cycle);
    • Fade 2: Red, green, blue, cyan, yellow, purple, white (7 kinds of colors of cycle);
    • Smooth 1: Yellow, green, cyan, blue, purple, white, red (16 kinds of colors of cycle);
    • Smooth 2: Red, yellow, green, cyan, blue, surpie, white (7 kinds of colors of cycle);
    •  Timer: 2H, 4H, 6H;
  • Brightness adjustable: Yes,  5 levels;

  • Memory function: Yes.

    • The max remote range is 200FT/61M(in air),10‐16.4FT/3‐5M (underwater), suggest remot 164FT/50M in air, 5FT/1.5M underwater.
      Schematic diagram of four lamps controlled by one remote control

AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig11

Tips:

  1. Remove the plastic insulation film on the bottom of remote control.
    AUDLES Premium ABS Shell Rechargeable Submersible LED Light with Magnets and
Plastic Plate - fig12

  2. When using remote control, make sure the rechargeable submersible light is on.

  3.  One remote can control all lights, no need to aim at the lights one by one. (Press longer or more when some lights don’t response)

  4. Check if the remote works
    Remote works: Press any button on the remote, small light is on.
    Remote NOT works:
    Press any button on the remote, small light is off. Please replace new battery.

  5. Checking timer:
    Press the button “ON”, how many times the light flashes, it means how many hours let in timer.

Note:
This  remote  control  is  suitable  for  all  controllable  lights  under the  brand,  and  the  upgraded  rechargeable  submersible lights can only be controlled by this remote control.

  Tips

  1. For Battery:
    When the light stays in flashing red light, it means the light will be out of power soon, please charge it.

  2. For Waterprock:
    •  Don’t open the light by yourself, otherwise it will lead to leak
    •  Please don’t use in hot water for too long, because the vapour may go into the light, it will damage the  components and lead to stop working,
    * Please keep the remote control dry from water, because it’s not waterprock.

Specification

  • Product Size3.15×3.15×1.52 inch

  •  LED16 LEDs

  • MagneticRustproof

  • Waterproof LevelIP68

  •  Light of fully charged  4H

  •  GluePowerful

  • Dimension of remote control 1.57×3.39×0.28 inch

  •  Color16 Colors (white, red, blue, green, yellow, purple and more)

  • Dynamic modes6 Kinds (FLASH1/2, FADE1/2,SMOOTH1/2)

  •  Color Changing  Yes

  • Bright Adjustable  Yes,5 Levels

  •  Timer2H, 4H, 6H

  • Remote ControlRadio Frequency
    ” Battery polymer lithium2500mAh (rechargeable)
    ” Battery of Remote Control1x CR2025 (included)

  • Max Remote Range  100FT/30M (in air),10‐16.4FT/3‐5M (underwater)

  • Suggest Remote Range  65FT/20M (in air),5FT/1.5M (underwater)  ” MaterialABS

Wide Usage

Submersible led light works well in both wet and dry places, such as swimming pool, bathtub, pond, boat,  fountain, aquarium, vase base, fish tank, flowerpot, garden, waterfall, and hallway, bar, garage, state, stage, showcase,  ideal  for  party,  birthday,  events,  holiday,  festival decoration,  like  Wedding,  Carnival  Halloween,  Christmas, Birthday party, etc.

Warranty and Service

  1. Warranty:  30  days  free  return  and  quickly  unconditional  refund,  2  years  free  replacement  for  product  quality issue (NOT MAN MADE).
  2. Service: Life to you with Lifetime prom in 24 hours, a mpt customer and give you service. Any 100% satisfy y questions, p ing solutions please don’t   .  hesitate to re ach out, we will reply

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals