Honeywell Home PRO TH1000E1 Programmable Thermostat Installation Guide

June 12, 2024
Honeywell Home

PRO TH1000E1/ TH1000DH/ TH2000DH Series Thermostats
Installation Guide

Read before installing

This manual covers the following models

  • TH1100DH: For Heat only systems
  • TH2110DH/TH1110E1/TH1110DH: For 1 Heat/1 Cool systems
  • TH2210DH/TH1210DH: For 2 Heat/1 Cool heat pump systems only (Pull thermostat from Wallplate and turn over to find model number.)

System Types

TH2110DH/TH1110DH/TH1110E1:

  • Gas, oil, or electric heat with air conditioning
  • Warm air, hot water, high-efficiency furnaces, 1 Heat/1 Cool heat pumps, steam, gravity
  • Heat only
  • Heat only with fan
  • Cool only 750 mV heating systems

TH2210DH/TH1210DH:
2 Heat/1 Cool heat pumps
TH1100DH:

  • Gas, oil or electric heat
  • Warm air, hot water, steam, gravity
  • Heat only 750 mV heating systems

Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.
Need Help?
For assistance with this product please visit http://customer.resideo.com or call Reside Customer Care toll-free at 1-800-468-1502

Wallplate installation

Pull at bottom to remove thermostat from Wallplate.

Remove the Wallplate from the thermo-stat as shown at left, then follow direc- tions below for mounting.

  1. Pull wires through wire hole.
  2. Position Wallplate on wall, level and mark hole positions with pencil.
  3. Drill holes at marked positions as shown below, then tap in supplied wall anchors.
  4. Place Wallplate over anchors, insert and tighten mounting screws.

Honeywell Home PRO TH1000E1 Programmable Thermostat -
Wallplate1

CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact the Thermostat Recycling Corporation at wwwihermostat-recycle.org or 800-238-8192 for information on how and where to properly and safely dispose of your old thermostat.

Power options

Honeywell Home PRO TH1000E1 Programmable Thermostat - Power
options

Wiring

Terminal designations
TH2110DH/TH1110E1/ TH1110DH:
B Changeover valve energized in heating
O Changeover valve energized in cooling
G Fan relay
Y Compressor contactor
W Heat relay
C 24Vac common. For 2-transformer systems, use common wire from cooling transformer.
R 24Vac power from heating transformer
b 24Vac power from cooling transformer

TH1100DH:
W Heat relay
C 24 Vac common
R 24 Vac power

TH2210DH/TH1210DH:
B Changeover valve energized in heating
O Changeover valve energized in cooling
G Fan relay
Y Compressor contactor Aux/E Auxiliary heat relay
C 24 Vac common
R 24 Vac power

Wiring guide — conventional and heat pump systems

2H/1C Heat Pump System
TH2210DH/TH1210DH

B Changeover valve energized heating [5] O Changeover valve energized cooling [5] G Fan relay
Y Compressor contactor
Aux/E Auxiliary heat relay
C 24Vac common [3] R Power [1]

1H/1C System
TH2110DH/TH1110E1/ TH1110DH
(1 transformed)

G Fan relay
Y Compressor contactor
W Heat relay
C 24 Vac common [3, 4] R Power (heating transformer) [1, 2] Rc Power (cooling transformer) [1, 2]

Heat Only System
TH1100DH

W Heat relay
C 24Vac common [3] R Power [1] See [notes] below
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means and overload protection as required.
[2] Remove jumper for 2-transformer systems.
[3] Optional 24 Vac common connection.

1H/1C Heat Pump System TH2110DH/TH1110E1/TH1110DH [7]

B Changeover valve energized in heating (5] O Changeover valve energized in cooling [5] G Fan relay
Y Compressor contactor [6] W [W-Y joined by jumper] C 24Vac common [3] R [R+Rc joined by jumper] Rc Power [1]

Heat Only System
TH2110DH/TH1110E1/TH1110DH

W Heat relay
C 24Vac common [3] C [R+Rc joined by jumper] Rc Power [1]

Heat Only System with Fan
TH2110DH/TH1110E1/TH1110DH

G Fan relay
W Heat relay
C 24 Vac common 3] R [R+Rc joined by jumper] Rc Power [1]

Cool Only System
TH2110DH/TH1110EUTH1110DH

G Fan relay
Y Compressor contactor
C 24 Vac common [3] R [R+Rc joined by jumper] Rc Power [1] [4] Common connection must come from cooling transformer.
[5] Use either O or B terminals for changeover valve.
(6] Use a small piece of wire (not supplied) to connect Wand Y terminals.
[7] Stefan operation switch to Heat Pump (see page 5).

Fan operation settings

TH2110DH/TH1110E1/ TH1110DH only:

  • Gasser Oil: For gas or oil heating systems, leave the fan operation switch in this factory-set position. (This setting is for systems that control the fan in a call for heat.)
  • Electric or Heat Pump: Change the switch to this setting for heat pump or electric heat systems. (This setting is for systems that allow the thermostat to control the fanon a call for heat, if a fan wire is connected to the G terminal.)

Honeywell Home PRO TH1000E1 Programmable Thermostat -
settings

Thermostat mounting

Align the 2 tabs at the top of the wall-plate with corresponding slots on the back of the thermostat, then push gently until the thermostat snaps in place.

Honeywell Home PRO TH1000E1 Programmable Thermostat -
settings1

Installer setup

Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired.
To begin, press and hold the▲ and ▼ buttons until the display changes.

Honeywell Home PRO TH1000E1 Programmable Thermostat -
settings2

Press the ▲ or ▼ button to change the setting.
Press the ▲and ▼ buttons simultaneously for one second to advance to the next function.
Press and hold the ▲ and ▼ buttons to exit and save settings.
NOTE: If you do not press any button for 60 seconds while you are in the setup menu, the thermostat automatically saves any changes made and exits the menu.

Setup function Settings & options (factory default in bold)

5 Heating cycle rate (CPH: cycles/hour)
TH2110DH, TH1110E1, TH1110DH and TH1100DH| 5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficient-cy
6 For electric furnaces
[Other cycle rate options: 2 or 4 CPH]
6 Auxiliary heat cycle rate (CPH)
TH2210DH and TH1210DH| 5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
6 For electric furnaces
[Other cycle rate options: 2 or 4 CPH]
9 Compressor cycle rate (CPH)| 3 Recommended for most compressors [Other cycle rate options: 1, 2, 4, 5, or 6 CPH]
13 Early Start (TH2110DH and TH2210DH)| 1 On **See page 8
0 Off
14 Temperature display| 0 Fahrenheit
1 Celsius
15 Compressor protection| 1 Five-minute compressor off time (See page 8)
0 No compressor off time
20 Clock display (TH2110DH and TH2210DH)| 0 12-hour display
1 24-hour display
25 Lower temperature range (TH1100DH only)| 0 Standard range 40°F to 90°F (4.5°C to 32°C)
1 Lower range (for garage mode) 35°F to 90°F (1.5°C to 32°C)
40 Restore program schedule to default (TH2110DH and TH2210DH)| 0 off
1 On – program schedule default settings are listed in the operating manual

CAUTION: EQUIPMENT DAMAGE HAZARD
Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.

Special functions

Early Start (Setup Function 13): Early start allows the heating or cooling to turn on before the program start time, so the temperature is reached at the time you set.
Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes before restarting, to prevent damage. During the wait time, the message Cool On (or Heat On for TH2210DH & TH1210DH) will flash on the display.

Accessories & replacement parts

Please contact your distributor to order replacement parts.
Cover plate assembly ……………………………………….. Part Number 50002883-001 Use to cover marks left by old thermostats.

Specifications

Temperature Ranges

  • Cool : 50° to 99°F (10° to 37°C)
  • Heat: 40° to 90°F (4.5° to 32°C)
    TH1100DH heat can be set to 35°F to 90°F (1.5°C to 32°C)

Operating Ambient Temperature

  • -32° to 120°F (0° to 48.9°C)

Shipping Temperature

  • 20° to 120°F (-28.9° to 48.9°C)

Operating Relative Humidity

  • 5% to 90% (non-condensing)

Physical Dimensions

  • 3-7/16”H x 4-10/16”W x 1-3/16”D
    87mm H x 119mm W x 30mm D

Electrical Ratings

System Voltage (50/60Hz) Running Current
Heat (1st stage) 20-30 Vac 0.02-1.0 A
(Power pile) 750 mV DC 100 mA DC
Auxiliary heat 20-30 Vac 0.02-1.0 A
Cooling 20-30 Vac 0.02-1.0 A

The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.

www.resideo.com
Resideo Technologies Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
69-2609EFS—15 M.S. Rev. 05-22 | Printed in United States
© 2022 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell
International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.
® U.S. Registered Trademark. Patents pending.
Copyright © 2022 Resideo Technologies, Inc.
All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Honeywell Home User Manuals

Related Manuals