KENWOOD XM50F 2-Way Rear Speakers Instruction Manual

: June 12, 2024
: KENWOOD

Table of Contents

KENWOOD XM50F 2-Way Rear Speakers
Product Information
Features and Specifications
Product Usage Instructions
SAFETY PRECAUTION
Section 1 – XM50F Front Speaker Installation Instructions
Section 2 – XM50R Rear Speaker Installation Instructions
KENWOOD LIMITED WARRANTY
Features and Specifications
ABOUT COMPANY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KENWOOD XM50F 2-Way Rear Speakers

KENWOOD-XM50F-2-Way-Rear-Speakers-FIG-1

Product Information

The XM50F and XM50R are front and rear speakers manufactured by JVCKENWOOD Corporation. These speakers are designed for use in vehicles and provide high- quality audio performance for an enhanced listening experience.

Features and Specifications

Impedance: 2 Q
Mounting Depth: 2 11
Sensitivity: 94dB
Frequency Response: 40-25kHz
RMS Power Handling: 150W
Peak Power Handling: 300W

For more information, including the latest Instruction Manual, please visit the official Kenwood website: https://manual.kenwood.com/en_contents/search/

Product Usage Instructions

Installation procedure:

Turn off your vehicle’s ignition switch.
Remove the outer fairing/headlamp assembly and set it aside. Refer to a service manual if needed.
Place a towel or similar protective material on the front fender to prevent damage.
Gently pull off the wires from each speaker, one at a time.
Undo the screws that attach each speaker/grille assembly to the inner fairing and remove them.
Gently pull out the stock speaker from each grille assembly.
If replacing previously installed aftermarket speakers, re-install the correct-sized connectors onto the factory speaker wires.
Attach the female OE in-line connectors to the male connectors on each new speaker. Ensure they are properly connected.
Turn on your radio to confirm that both speakers are playing.
Re-install the fairing/headlamp assembly.

XM50R Rear Speaker Installation Instructions
The installation procedure for the XM50R rear speakers is not provided in the manual extract. Please refer to the complete user manual or contact Kenwood support for detailed instructions on installing the XM50R rear speakers.

Register Online
Register your KENWOOD product at https://registerkenwood.us.jvckenwood.com/

SAFETY PRECAUTION

CAUTION
To avoid the risk of human injur y or proper ty damage, be sure to read and observe the following safety precautions:

Consult a professional technician for installing and connecting the speaker.
Incorrect installation may lead to traffic accidents or malfunctions.
Avoid installation where the speaker in unstable.
Make sure that the speaker is stationary and does not rattle. Displacement of the speaker may cause injury.
Do not modify the speaker.
Doing so may result in smoke or fire.
Keep the volume of sound at an optimum level.
Not being able to hear sounds from your surroundings can lead to traffic accidents.
In case of abnormality, stop the use and disconnect the speaker.
If operation is continued, smoke or fire may result. Disconnect the speaker and ask servicing.
Always wear protective eyewear during installation.
To prevent short-circuit, keep all wiring away from moving parts, sharp edges, cut metal, etc.
When removing or installing the grille, be careful not to brush the unit with the edge of the grille.
Do not switch ON power until wiring is completed.

FOR PROPER INSTALLATION AND USE
Please read the instructions carefully before using this speaker:

Be careful not to accidentally kick or apply any sort of strong impact to the speaker.
To prevent damaging the speaker, turn off the power of the amplifier before connecting it to the speaker.
Do not use the provided parts for other purposes Otherwise malfunction or fire hazard could result.

NOTE
Observe the following cautions to prevent damage to the speakers:

You cannot input the same power as “peak power” continually.
When the volume is set too high, the sound may be distorted or abnormal. Reduce the volume promptly in case of such phenomena.
KENWOOD XM50F and XM50R speakers will work best when powered by an amplifier. They have an imedance of 2 ohm and will cause damage if wired directly to the built-in radio power in ‘98-’05 factory Harley Davidson® motorcycles.

Section 1 – XM50F Front Speaker Installation Instructions

Installation procedure

With your ignition switch in the “OFF” position, remove your outer fairing/headlamp assembly and set it aside. Refer to a service manual if you need help with this. It’s always a good idea to have a towel or something similar on your front fender to avoid dings or scratches if anything is dropped.
Take the 2 wires off each speaker by gently pulling one at a time. Undo the screws that attach each speaker/grille assembly to the inner fairing and remove them. Gently pull the stock speaker out of each grille assembly.
Although the XM50F speakers will work behind the factory grille cloth, the metal mesh grilles in this kit are designed to replace the front speaker grille cloth on 1998-2013 HD Street Glides, Ultras, Classics, and Standards. The factory grille cloth is glued to a plastic mesh, and together, is two-way taped to the main body of the grille assembly. You can usually peel away the mesh from the body of the grille by hand. With the factory grille cloth/mesh off, you should see the exposed two-way tape used to hold the factory mesh on the main grille body. Before applying the new mesh, have a look as you will see it only “lines up” one way.
“Clip” the XM50F speaker into each grille assembly so the speaker terminals are adjacent to the thickest part of the speaker/grille assembly. When installed, this puts the speaker terminals in the 12 o’clock (top) position. You DO NOT want the speaker connectors in the 6 o’clock (bottom) position, as they may short out against the silver horizontal fairing bracket. Place your new speaker/grille assembly onto the inner fairing and re-attach each one using the OE screws. A hand screwdriver is recommended for this step.
Since these speakers are a direct replacement for the OE speakers, the female OE “in-line” connectors mate with the male connectors on each speaker and only go on one way. If you are replacing previously installed aftermarket speakers, you may need to re-install the correct sized connectors (not supplied) onto the factory speaker wires, noting that the smaller connector is the positive (+).
Once you are confident the factory wires are correctly attached to the new speakers, turn on your radio to confirm that both speakers are playing. Then, re-install your fairing/headlamp assembly.

Section 2 – XM50R Rear Speaker Installation Instructions

With your ignition switch in the “OFF” position, remove the factory speaker grilles by undoing the 4 screws on the front of the grilles. Carefully lift up each speaker and take the 2 wires off by pulling one at a time from the stock speaker. Then, remove the speakers.
The female OE “in-line” speaker connectors mate with the male connectors on each speaker and only go on one way. If you are replacing previously installed aftermarket speakers, you may need to re-install the correct sized connectors (not supplied) onto the factory speaker wires. Once you are confident the factory wires are correctly attached to the new speakers, sit them in place, put the grilles back on, and then secure the speaker by reinstalling the 4 screws per grille.
NOTE: The factory rubber “nutserts” on the rear pod side can be finicky. It’s a good idea to get all 4 grille screws “started” and then get each one snug. Gradually tighten each one down making sure all 4 screws holding the grille down are secure!
Turn your radio on and confirm that both speakers are playing.

KENWOOD LIMITED WARRANTY

This warranty will be honored only in the U.S.A.

HOW LONG IS THE WARRANTY
JVCKENWOOD USA Corporation (“KENWOOD”) warrants this product for a period of one (1) year from the date of original purchase.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material and workmanship in KENWOOD products.
The following are not covered by the warranty:

1. Any product which is not distributed in the USA by KENWOOD or which is not purchased in the USA from an authorized KENWOOD dealer or an automobile dealer, unless the product is purchased through the U.S.A. Military Exchange Service.
2. Any product on which the serial number has been defaced, modified or removed.
3. Damage, deterioration or malfunction resulting from:
  * Any shipment of the product (claims must be presented to the carrier).
  * Installation or removal of the product.
  * Accident, acts of nature, misuse, abuse, neglect, unauthorized product modification or failure to follow instructions supplied

with the product.

  * Repair or attempted repair by anyone not authorized by KENWOOD.
  * Any other cause which does not relate to a product defect.

WHO IS PROTECTED
This warranty is enforceable only by the original purchaser.
WHAT WE WILL PAY FOR
We will pay for all labor and material expenses for covered items. Payment of shipping charges is discussed in the next section of this warranty.
HOW TO OBTAIN WARRANTY SERVICE
If your KENWOOD product ever needs service:

1. Take or ship it to any KENWOOD Authorized Service Center in the USA along with a complete description of the problem. (if you are uncertain as to whether a Service Center is authorized, please call 1-800-KENWOOD (1-[800-536-9663](https://phone.gd/phone/800-536-9663)) for the nearest Service Center.
2. Although you must pay any shipping charges if it is necessary to ship the product for warranty service, we will pay the return shipping charges if the repairs are covered by the warranty within the United States.
3. Whenever your units are taken or sent for warranty service, you must include a copy of the original dated sales receipt as proof of warranty coverage.

LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF DAMAGES
KENWOOD’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION. KENWOOD SHALL NOT BE LIABLE FOR:

1. INSTALLATION OR REMOVAL CHARGES, DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN KENWOOD CAR STEREO COMPONENTS, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT; OR
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If a problem develops during or after the Limited Warranty Period, or if you have any questions regarding the operation of the product, you should contact your KENWOOD Authorized Dealer or Authorized Service Center. If the problem or your question is not handled to your satisfaction, please contact our Customer Relations Department at the address listed below:

Important Notes
©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley- Davidson, Inc. and/or its affiliates and if used or implied are for reference only. There is no affiliation between Harley-Davidson, Inc. and/or its affiliates and JVCKENWOOD Corporation and/or its affiliates. All other trademarks are the property of their respective owners. Specifications subject to change without notice.

For updated information (the latest Instruction Manual, etc.), please visit the following website:
https://manual.kenwood.com/en_contents/search/

KENWOOD-XM50F-2-Way-Rear-Speakers-FIG-2