BOSCH SHV4AEB3N Dishwasher Instruction Manual

BOSCH SHV4AEB3N Dishwasher

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire and injury to persons. When using kitchen appliances, basic safety precautions must be followed including those in the following pages.

Safety definitions

Here you can find explanations of the safety signal words used in this manual.

WARNING
This indicates that death or serious injuries may occur as a result of non- observance of this warning.

CAUTION
This indicates that minor or moderate injuries may occur as a result of non- observance of this warning.

NOTICE:
This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.

Note: This alerts you to important information and/or tips.

General information

To reduce the risk of fire, electrical shock, or serious injury, observe the following.

• Read and understand all instructions before using the appliance.
• Keep the provided documents in a safe place for future reference or for the next owner.
• Do not connect the appliance if it has been damaged in transit.
• Severe product damage and/or injury could result from the use of unqualified service technicians or nonoriginal parts. All repairs must be performed by an authorized service provider using only original equipment factory replacement parts.
• NSF/ANSI 184 Certified residential dishwashers are not intended for licensed food establishments.

Safe Installation

Follow these safety instructions when installing the appliance.

• These instructions are intended for use by qualified installers only. The dishwasher must be installed by a qualified technician or installer.
• The dishwasher drain hose must be installed with a portion of it at least 33″ (84 cm) off the floor; otherwise the dishwasher may not drain properly.
• This dishwasher is not for outdoor use. It is intended for indoor residential use only, and should not be used in commercial food service establishments.
• This dishwasher is designed to be enclosed on the top and both sides by cabinetry.
• NEW INSTALLATION – If the dishwasher is a new installation, ensure all connections are properly made before the dishwasher is moved into place.
• REPLACEMENT – If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary.
• This appliance has been found to be in compliance with CAN/CSA-C22.2 No. 167/UL 749. It is the responsibility of the owner and the installer to determine if additional requirements and standards apply in specific installations.

WARNING

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. Hydrogen gas is explosive.

• Before using a dishwasher that is connected to a hot water system that has been unused for two weeks or longer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is explosive, do not smoke or use an open flame during this time.

Electrical safety

Follow these safety instructions to avoid electrical shock.

• The dishwasher must be properly grounded before operating. This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher.
• DO NOT use an extension cord
• DO NOT reuse an old power cord; only use the cord provided.
• Make sure that the dishwasher is connected to a suitable ground in compliance with all local codes or, in the absence of a local code, with the NATIONAL ELECTRICAL CODE in the United States or the CANADIAN ELECTRIC CODE C22.1-latest edition in Canada as well as any provincial/state or municipal or local codes that apply
• Installations requiring hard wiring and terminal block – The accessory terminal block/junction box model, SMZPCJB1UC, designed for permanent wire connection, is not included but can be ordered through Customer Service by calling 1-800-944-2904. Follow the instructions included with the kit.

WARNING

Avoid Electrical Shock

• Do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.
• To avoid possible injury or property damage, care should be exercised when the dishwasher is installed or removed to reduce the likelihood of damage to the power cord.

WARNING

Avoid Fire Hazard

• Make sure electrical work is properly installed and checked by qualified electricians.
• Make sure there are no loose electrical connections. Make sure all electrical connections are properly made.
  Loose and improperly installed electrical connections can result in overheating!

Wall outlet connections

• Only use the provided power cord for wall socket connections.
• DO NOT attach an extension cord or any type of modified cord or adapter with this appliance.
• DO NOT cut or splice the power cord.
• DO NOT alter the power cord in any way.

Permanent wire connections (in addition to the warnings above)

• Only use the junction box power cord, sold as Accessory kit #SMZPCJB1UC.
• Carefully review the terminal block installation instructions.
• DO NOT remove, alter or bypass the terminal block.

State of California Proposition 65 Warnings

This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:

STATE OF CALIFORNIA PROPOSITION 65 WARNING:

WARNING
Cancer and Reproductive Harm – vvww.P65Warnings.ca.gov

Before you begin

Read these instructions before you begin to install your appliance.

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. Cosmetic defects must be reported within 30 days of installation. NOTE: Do not discard any bags or items that come with the original package until after the entire installation has been completed.

Parts Included

After unpacking all the parts, check for any damage in transit or missing parts.

| Power Cord
---|---
| Screw Clamp
| Spring Clamp
| Mounting Brackets Mounting Bracket wood screws for attaching to cabinetry
| Screws for mounting bracket installation, leg leveler locking, and toe panel If your model comes with a white toe panel, use stainless steel screws for attachment
| Toe Panel
| Fully integrated panel kit and instructions *depending on your model

Tools and Parts Needed

Gather these tools and additional parts before beginning the installation of your appliance.

Tools

| Power drill
---|---
| Hole saw
| Measuring tape
| Phillips screwdriver
| Flat screwdriver
| Adjustable wrench x2
| Pliers
| Level
| Coarse sandpaper
| Elbow connection with 3/4″ female hose threads on one end fits your water supply line on the other.
| Water inlet hose – minimum 3/8″ outer diameter copper tubing or metal braided dishwasher supply line. * Both the elbow and the water inlet hose can be found in the dishwasher supply kit SMZSH1ABUC.
| Shut-off valve and fittings appropriate for hot water supply line.

Pre-install Checklist

Ensure that the following requirements are met when planning the installation of your appliance.

WARNING

Avoid Scalding or Electric Shock Hazard

• Make sure the water supply and electrical supply are shut off before installation or service.
• Do not allow the electrical and supply lines to touch.
• Select a location as close to the sink as possible for easy access to water supply and drain lines.
• Be sure the unit is installed close enough to the sink so the drain hose length does not exceed 92″ (2337 mm) and so that a portion of the drain hose is raised at least 33″ above the floor level.
• Ensure that the enclosure is square and the opening is at least 34″ ( 863.3 mm) high and 24″ (609.6 mm) wide.
• Check that the opening in the cabinet is large enough for routing the electric cable, water line, and drain hose, and if not, create a new opening. See
• If the opening is wood, be sure it is sanded smooth. If it is metal, be sure it is covered by a protective gasket.
• Be sure that your water heater set at 120° F (49° C) and the water pressure measures at 15-145 psi (1-10 bar)
• Determine the mounting method based on the dishwasher model and counter-top type. See → “Mounting Brackets”, Page 9.
• Only use the included hardware for the installation. If you are replacing a dishwasher, dispose of old hose and other equipment properly.
• To avoid scratching the floor, have floor protection ready for when the dishwasher will be slid into the cabinet.

Electrical Requirements

Ensure that the following electrical requirements are met.

Dishwasher electrical rating

Volts

|  120
---|---

 Hertz

|

60 Amperes

12 Watts|

 1,440 (max)

Electrical Supply

The customer has the responsibility of ensuring that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated 15 or 20 amps.

Cabinet Requirements

Ensure that the cabinet space for the installation meets the required dimensions.

If the dishwasher is to be installed in a corner, ensure that there is adequate clearance to open the door as shown.

Installation Preparation

After locating the proper place for your dishwasher, create an opening to allow for water, drain and electrical lines on the appropriate side.

1. Cut a hole within the 7 x 2.5″ area shown.
   
   If the opening is made through wood, sand it smooth.
   If the opening is made through metal, use the Edge
   Protector with Power Cord clips Kit SMZEPCC1UC.

2. Remove the drain hose from inside the dishwasher.

3. Remove the toe panel fleece from the back of the dishwasher.
   

Installation Procedure

Follow these instructions to install the dishwasher.

Attach Water Inlet Hose

NOTICE:

Avoid cross-threading

• Cross-threading will cause leaks. Teflon tape
• Do not use Teflon tape; it could cause leaks and damage floors or cabinetry.

1. Carefully flip the unit over onto its back side with the door facing up.
   

2. Remove the toe panel from the front of the unit (set aside for later) and loosen the feet slightly.
   

3. Attach the elbow to the water inlet valve on the front of the dishwasher.
   

4. Attach the hot water line to the elbow. Use two wrenches to tighten, using one to stabilize and avoid putting stress on the water inlet valve.
   

|
---|---

Attach Drain Hose

1. Flip unit back upright, making sure the waterline is not pinched.

2. Facing the back of the unit, orient the drain hose toward direction of sink.
   
   IMPORTANT: Route hose toward sink PRIOR TO connection. Do not turn after attachment.

3. Attach drain hose elbow to back of unit using pliers to install the spring clamp

Pre-level the Dishwasher

Set the dishwasher to the correct height before it goes into the cabinet.

1. Measure the height of the cabinet opening.

2. Raise the front of the dishwasher to approximately 1/2″ lower than the height of the opening by turning all three feet.
   
   The maximum height the unit can be raised to is 34.5″ (867.3 mm)

3. Use a level on the top front to see that the feet are even.

4. Once the unit is at a satisfactory height, insert a leg leveler locking screw in back foot.
   

Attach Power Cord

• Plug the end of the supply cord into the back of the dishwasher.
  • Be sure to push it all the way in until fully seated.
    
    The outlet for the power supply cord should be located in a cabinet or wall adjacent to the dishwasher cabinet.
    Do not plug dishwasher into the wall outlet until all the steps of the installation are complete.

Notes

• Only use the included power cord. If cord is missing order kit SMZPC002UC through Customer Service.
• If you require a permanent wiring connection, order kit junction box accessory kit SMZPCJB1UC.
• If local electrical codes require clips to secure the power cord wire to the dishwasher, use accessory kit SMZEPCC1UC.

Mounting Brackets

Before installing the supplied mounting brackets, decide which method of securing the dishwasher into its enclosure will be used, top (wood or porous material) or side (stone or solid surface). Once the mounting brackets are installed on the dishwasher, removing them is difficult and will damage the mounting brackets and the dishwasher. If you have a Fully Integrated Panel, do not attach mounting brackets until after attaching the panel to the door.

WARNING

Avoid tip over hazard

• Do not use the dishwasher until it is completely installed. When opening the door on an uninstalled dishwasher, carefully open the door while supporting the rear of the unit. Failure to follow this warning can result in serious injury.

Top Mount
Top Mount is used for counter tops made of wood or other materials that can be easily drilled.

CAUTION

Avoid sharp edges

• Do not break the mounting brackets; causes sharp edges.

1. Grasp mounting bracket with pliers and fold bracket at the perforation over onto itself.
   

2. Attach mounting brackets to the frame with included 3/4″ (19mm) screws.
   

|

---|---

Side Mount

Side Mount is used for countertops made of marble, granite, or other solid surface material that cannot be easily drilled.

1. Grasp mounting bracket with pliers and fold bracket at the perforation over onto itself.
   

2. Attach mounting brackets to the frame with included screws.
   

|
---|---

Install Dishwasher in Cabinet Space

To avoid scratching the floor, use floor protection and caution when sliding the dishwasher into the cabinet.

1. Feed the power cord through the low hole in the cabinet first and then add the hoses.

2. Using both hands, push dishwasher 1/3 of the way into the cabinet and STOP.
   

3. Pull the hoses and power cord through the hole in cabinet as shown.

4. Push the unit 2/3 of the way into the opening and STOP.
   

5. Reach into adjacent cabinet and pull hoses and excess power cord completely out so they do not get kinked.
   

6. Finally, push the unit in until flush with cabinet door.
   

Level the Dishwasher

Now that the dishwasher is in the cabinet, check the levels again.

1. Level side to side by turning feet clockwise to raise or counter-clockwise to lower front.
   

2. Use a level to check that your dishwasher is level. Check that the countertop is level and adjust the dishwasher to the countertop.
   

3. Make sure the top of the door is no less than 1/4″ (6mm) from the underside of the counter.
   

|
---|---

Outer Door Assembly

• Follow the instructions for outer door assembly on the fully integrated template.

Note: The door panel should weigh between 9 and 18 lbs, be at least 3/4″ thick, and not exceed 30 1/8″ in length.

Secure the Dishwasher

1. Center the dishwasher in the opening.
   

2. If using the Top Mount, and screw the 1/2″ (12.7mm) wood screws through the holes in the mounting brackets. Choose the bracket hole best suited for your installation.
   
   If the dishwasher came with a protective barrier, screw through the barrier.

3. For Side Mount, lift the flap on the deco strip and insert the 1/2″ (12.7mm) wood screws underneath.
   

|
---|---

Dishwasher Connection

Follow these instructions to connect the dishwasher.

Installing the Water Inlet Connection

The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 – 145 psi (1 – 10 bar).

WARNING

Scalding Hazard

• Do not perform any work on a pressured hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off.

NOTICE:

Soldering plumbing lines

• Temperatures required for soldering and sweating will damage the dishwasher. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher. Plumbing codes
• Check local plumbing codes for approved plumbing procedures and accessories. All plumbing should be done in accordance with national and local codes.

Note

Important notes for water connection:

• If using a solder joint instead of a compression fitting, be sure to complete all solder connections before connecting the water supply line to the dishwasher.
• Use an approved dishwasher water supply line with the correct fittings for this connection.
• If using copper tubing or other material not depicted in this manual for water supply, defer to a licensed plumber for proper installation.
• Always use appropriate seals when making plumbing connections.

1. Flush the incoming water line for approximately 1 minute to clear any foreign material.

2. Connect the dishwasher water supply line to the water shut off valve.
   ‒ Install a shut off valve if one isn’t already in the supply line.
   ‒ Make sure there are no sharp bends or kinks in the water line that might restrict water flow.
   

3. Properly tighten all water connections.

4. After all connections are made, turn on the hot water and check for leaks.

Installing the Drain Connection

The drain hose must be installed with either a high loop or an air gap.

NOTICE:

Proper drain hose installation

• The dishwasher drain hose must be installed with a portion of it at least 33” (84 cm) off the floor; otherwise the dishwasher may not drain properly. Remove garbage disposal plug
• If the dishwasher drain hose will be connected to a garbage disposal connection, first remove the plug from the disposal connection.

Note

Important notes for drain connection:

• If local ordinance require an air gap, install it according to the manufacturer’s instructions.
• The drain hose length can be extended if necessary. Use kit #SGZ1010UC. The maximum length of the drain hose, including the hose leading to the air gap, is 150″ (380 cm).

1. Place hose clamp around end of drain hose BEFORE connecting to the plumbing.
2. If you have a garbage disposal, connect the drain hose to the garbage disposal with either a high loop or an air gap.
   |
   ---|---

3. If you do not have a garbage disposal, connect the drain hose to the drain connection with either a high loop or an air gap.
   |
   ---|---

4. Tighten the hose clamp around the house plumbing.
   

Electrical Connection and Test Cycle

1. For wall outlet connections, plug the dishwasher into the outlet.
2. Turn on power supply.
3. Make sure the water supply is on.
4. Turn the dishwasher on and run a test cycle for 15 minutes.
5. Check to make sure the cycle operates and there are no leaks while it is running.
6. Stop the cycle and turn off the dishwasher.

Attach the Toe Panel

1. Remove the toe panel fleece from the packaging and insert it at the base on the front of the dishwasher.
   

2. Tuck the top of the fleece into the base front opening. If necessary, fold the lower edge under for a proper fit.
   

3. Attach the toe panel with the 3/4″ screws so it is flush with the floor. Use black screws for a black toe panel and stainless for a white toe panel.
   |
   ---|---

4. Your installation is complete!

Customer Service

With any warranty repair, we will make sure your appliance is repaired by an authorized service provider using genuine replacement parts. We use only genuine replacement parts for all repairs. Detailed information on the warranty period and terms of warranty can be found in the Statement of Limited Product Warranty, from your retailer, or on our website. If you contact Customer Service, you will need the model number (E-Nr.) and the production number (FD) of your appliance. USA:

1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA: 1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories
For assistance with connecting to Home Connect®, you can also view instructions here: www.home-connect.com/us/en/help-support/set-up

Model number (E-Nr.) and production number (FD)

You can find the model number (E-Nr.) and the production number (FD) on the appliance’s rating plate. The rating plate is located inside the appliance door. Making a note of your appliance’s details and the Customer Service telephone number will enable you to find them again quickly.

AquaStop® Pledge

In addition to the standard warranty provided by BSH, BSH will also compensate customers for damage caused by a specific fault in the AquaStop system giving rise to a valid warranty claim. Compensation will be provided under the following conditions:

• If water damage is caused by a defect in materials or workmanship in the AquaStop system, BSH will compensate customers reasonable and verifiable damages.
• A condition of all warranty claims is the appliance with AquaStop must have been installed and connected correctly in accordance with all instructions; this also includes a properly installed AquaStop extension (genuine accessories). The warranty does not cover defective feed lines or fittings leading to the AquaStop connection at the tap.

Register your appliance to enjoy customized benefits.

Thank you for being a Bosch customer!
Simply create a MyBosch account, then register your appliance.
You’ll find a variety of customized information in MyBosch such as:

• Discounts for filters, cleaners, accessories & parts
• Easy access to manuals & appliance specifications
• Easy access to part lists
• Customized offer for the Bosch Appliance Service Plan (sent by mail after appliance registration)

Register here: www.bosch-home.com/us/owner-support/mybosch

Looking for help?
You’ll find it here.

No matter what, no matter when: Bosch is here to support you.
We’re here to assist with usage instructions, cleaning tips, accessories & parts, troubleshooting, and repairs.
Find online resources such as FAQs, how-to-videos, manuals, warranties and authorized Bosch servicers at: www.bosch-home.com/us/owner-support/get- support

Contact us:

Please have your Model Number (E-Nr) ready when contacting us.
1-800-944-2904
www.bosch-home.com/us/owner-support/contact-us

BSH Home Appliances Corporation
1901 Main Street, Suite 600
Irvine, CA 92614
USA
www.bosch-home.com
1-800-944-2904
© 2023 BSH Home Appliances Corporation

References

• here.no
• Home Appliances Global Website | Bosch
• Welcome to MyBosch
• Help & Support | Home Connect

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>