DIAS Automotive Electronic C234 NFC Reader Module User Manual

June 12, 2024
DIAS Automotive Electronic

DIAS Automotive Electronic C234 NFC Reader Module

Product Overview

Product Introduction
In LPCD mode, the near field communication module can wake up the NFC device on the vehicle side when the NFC card or mobile phone is near, and then enter the standard Polling mode. When a matching card is detected, the polling mode is activated. LIN informs VKM and CAN informs BCM to open or close the door.

Technical Specification

Product specifications are as follows

Table: 1 1 Product specification parameter

Product name NFC Reader Module

Product Features

| Model| C234| Dimension| 85×19×6mm
Material| PC+ABS| Weight| <80g
Power Supply| DC 6~16V| Waterproof class| IP6K8
Processor| 32bit 120MHz
Storage| RAM| 32KB| ROM| 512KB
External Interface| 1 LIN、1 KL30、1 GND
Consumption| Detecting Period(30ms) : <0.45mA
Ambient| Operating

Temperature

| -40~85℃| Storage

Temperature

| -55~90℃
Communication

Mode

| ISO/IEC 14443A/B/MIFIARE
Digital Key

Protocol

| ICCE
Operating

Frequency

| 13.56MHz

Hardware Introduction

Appearance Introduction
The dimensions of the NFC body are about 85 x 19 x 6mm, and the front and rear shells are affixed with double sided tape. The sides are LIN, ground, and power interfaces, as shown in Figure 2 1.

Interface

Interface definition

Tale 2 1 : Interface Definition

SN Name Description
1 LIN LIN signal
2 Power Supply power KL30.
3 GND GND

Assembly Introduction

The C234 is placed inside the door handle and do not require extra fixing. Figure 2 3 show the installation positions.

Operation Instruction

The NFC valid card is placed near the NFC module, and the NFC module transmits information to the ECU with SE at the end of the car through LIN, and unlocks the car after the NFC card is certified.

Setup Up
Before the module can start normally, it is necessary to prepare a power supply, a valid NFC card, a wire harness, and a LIN communication tool. In addition to connecting the NFC reader module, the wiring harness also needs to connect to the LIN communicat ion tool. After the power supply is powered on, if the current is about 20mA, the NFC module is started. Figure 3 1 shows the following.

Swipe Care
Place a valid NFC card close to the NFC module, as shown in Figure 3-2.

Query Version

LIN Communication

  • Connect the DB9 port of Kvaser Lin on the wiring harness, connect the USB port of Kvaser Lin on the PC, and power on the device. The port shown in Figure 3 3 is identified in the device manager on the PC.

  • Click “Connect Device” in the LIN FLASH tool. “LIN Hardware Init OK” is displayed in Figure 3 4, indicating that the Kvaser Lin device is normal.

Query Version

  • Click “App Version Number” in the LIN FLASH tool, and the message “62 f1 95 02 06 01 04 14 00.” is displayed in Figure 3 5. Indicates that the version information of F195 is read.

FCC ID

Table 3 1 FCCID

Model FCC ID
C234 2BBZ4NFCC234

Product Informaiton

  • DIAS Automotive Electronic Systems Co.,Ltd.
  • Product: NFC Reader Module
  • Model: C234

FCC STATEMENT

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

DIAS Automotive Electronic Systems Co.,Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals