NEXT audiocom FLEXi15 Flexible PA System 15 Inch Subwoofer User Manual
- June 12, 2024
- NEXT audiocom
Table of Contents
NEXT audiocom FLEXi15 Flexible PA System 15 Inch Subwoofer User Manual
INTRODUCTION
GENERAL DESCRIPTION
Thank you for purchasing a NEXT Audiocom FLEXi System. This user manual will provide you with useful and important information about your equipment. Please devote some time reading it and keep it at hand for future reference.
The NEXT Audiocom FLEXi Series is composed by one 15″ subwoofer and two 8″ satellites designed for installations and portable solutions. The premium- quality components provide a balanced sound with an excellent low frequency extension. This system can be an ideal solution for hotels, restaurants, bars, lounges, conference rooms and many others.
ATTENTION! Because of the continuous evolution of techniques and standards, NEXT Audiocom reserves the right to change the specifications of its products without warning. For the most updated version of this manual and general information about this and other products, please visit our website www.nextaudiogroup.com.
UNPACKING
NEXT Audiocom’s products are built under strict quality guidelines and supervision, according to the highest standards. When unpacking your product, carefully examine it for any signs of possible transit damage and inform your dealer immediately if any such damage has occurred. It is suggested that you retain the original packaging so that the product can be repacked in the future when necessary. Please note that NEXT Audiocom and its authorized distributors cannot accept any responsibility for damage to any returned product using non-approved packaging.
SAFETY FIRST
Please take some time to review the following statements concerning safe use of your NEXT Audiocom FLEXi System.
- Read these instructions
- Keep these instructions
- Heed all warnings
- Follow all instructions
- Use the equipment only for its intended purpose as instructed in this manual
- Before installing, observe the applicable safety regulations for your country
- Always check if the equipment is installed securely and will not fall
- Do not attempt to move the enclosures while connected
- When mounted on a pole, always ensure that the floor or structure where the stack will take place is even and can withstand the weight
- Never install close to ignition or heat sources such as radiators, ovens or any other apparatus that produce heat
- Do not use or install the equipment near water or exposed to rain
- If the equipment is not functioning properly or has been damaged in any way, switch it off immediately
- Do not open or try to service the equipment. It may only be repaired by authorized, qualified personnel
- Clean the equipment using only a clean dry cloth
- Do not operate the unit for an extended period with the sound distorting
WARNINGS
CAUTION:
Never remove the cover, because otherwise there may be a risk of electric
shock. There are no user serviceable parts inside. Have repairs carried out
only by qualified service personnel.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions.
CAUTION:
This equipment is intended for professional use. Therefore, commercial use of
this equipment is subject to the respectively applicable national accident
prevention rules and regulations. As a manufacturer, NEXT Audiocom is
obligated to notify you formally about the existence of potential health
risks. Hearing damage due to high volume and prolonged exposure: When in use,
this product is capable of producing high sound-pressure levels (SPL) that can
lead to irreversible hearing damage in performers, employees, and audience
members.
For this reason, avoid prolonged exposure to volumes in excess of 90dB
HANDS ON
FLEXi 15 SYSTEM OVERVIEW
-
Main Level Adjustment
-
Subwoofer Level Adjustment
-
ON: Lights when the system is turned on
SIG: Lights when the system receives audio signal
CLIP: Lights when the system is clipping -
Preset List
-
Stereo Audio Input (2 x Balanced Combo XLR)
-
Subwoofer Phase Switch (0º or 180º)
-
Stereo Audio Output (2 x Balanced XLR)
-
Audio Input Switch (Mono or Stereo)
-
Preset Selection Push Button
-
Satellite Speaker Output (2 x SpeakON NL4 1+/1-)
-
Input Voltage Selector (110V or 230V)
-
Power Switch (On or Off)
-
Mains Power Input – IEC Connector / Protection Fuse (T12A/250V or T6.3A/250V)
-
Satellite Speaker Input – From Subwoofer (1 x SpeakON NL4 1+/1-)
CONNECTIONS
The NEXT Audiocom FLEXi 15 satellite speakers have a nominal impedance of 4Ω. Use two speaker cables with Neutrik NL4 connectors to link the subwoofer to the satellite speakers (dashed line). Both ends of the cable must be connected to 1+/1-.
Connect the desired audio source to the subwoofer using a TRS Jack or XLR
connector (bold line). In mono operatio, use only the LEFT signal input and
select MONO on “Input Type”. Expand your sound system linking two or more
FLEXi 15. Connect both systems using a XLR cable (solid line).
PRESETS AND FUNCTIONALITIES
Adjust the system preset according to your needs using the “Preset Selection” rotary encoder.
FLAT INDOOR – System’s Flat Response on Indoor Events – use this preset in live performances for clarity of voice and instruments.
FLAT OUTDOOR – System’s Flat Response on Outdoor Events – use this preset in live performances for clarity of voice and instruments.
MUSIC – System’s EQ for Music Reproduction – use this preset for recorded music playback applications.
DJ – System’s EQ for DJ Events – use this preset for electronic dance music applications.
VOCAL – System’s EQ for Speech – use this preset for speech or mainly vocal applications.
Use the “Subwoofer Phase” switch to reverse, or not, the polarity of the subwoofer. This can be useful when there is no summation between satellite speakers and subwoofer due to positioning. Try to reverse the polarity to check wether you get the better results.
ATTENTION!
By default, the system comes ready to operate at 230V. If you need to operate
at 115V, always remember to change the voltage switch to 115V and replace the
mains fuse by the one supplied with the equipment (T12A/250V) – all the
procedures must be done with the system disconnected from the power.
SERVICE
TROUBLESHOOTING
Problem: No sound coming from the satellite speaker
Action to Solution:
- Check volume levels on the subwoofer amplifier, signal sources and the connections between them. Check if the signal led is reacting to the signal source. If everything seems to be ok, connect another speaker known to be working to the subwoofer. If it works, the wiring to the satellite speakers may have problems, or the satellite speakers are damaged.
- Check that you have the correct pair of wires connected to the speakers you are trying to work with. Look for signs of damage if possible and check that the wires are correctly mounted on the connector and the connecter is correctly inserted on the speaker.
Problem: Little to no bass
Action to Solution:
- This happens most of the times when two or more speakers near each other, are wired out of polarity. In this case low frequencies will cancel each other acoustically. Check that the “+” on the subwoofer amplifier, is connected to the NL4’s 1+ and the “-“ marked on the subwoofer amplifier is connected to the NL4’s 1-.
Problem: Buzzing, hissing or humming
Action to Solution:
- If there is noise and no program material is playing, check your entire signal chain for the bad component. It can also be a matter of poor grounding or a ground loop. Check and correct the system grounding.
Problem: Sound is distorting with PEAK led OFF
Action to Solution:
- Reduce the level from the audio source, such as the mixer, increase the level on the input potentiometer.
Problem: Sound is distorting with PEAK led mostly ON
Action to Solution:
- Reduce the MAIN LEVEL on the subwoofer amplifier.
Problem: Weak high frequency response at listening point
Action to Solution:
- Probably the room is too absorbent or you are listening from a long distance. To increase the HF frequency response, select the FLAT OUTDOOR preset.
Problem: Poor low frequency connection between SUB+SAT
Action to Solution:
- Probably subwoofer and satellite speakers are out of phase. Invert the subwoofer phase using the “Subwoofer Phase” switch.
Problem: The subwoofer amplifier doesn’t turn on
Action to Solution:
- Check if the voltage selector is on the desired voltage position and the adequate fuse is in place. Check the fuse status, if the fuse is blown, replace it.
SIMPLIFIED EU DoC
Hereby, CVA ELECTRONICA, LDA declares that this equipment type is in compliance with the mandatory directives for the CE certification. The full text of the EU declaration of conformity is available at the following internet address: www.nextaudiogroup.com/en/apoio-ao- cliente/downloads
WARRANTY POLICY
NEXT Audiocom products are warranted, by NEXT Audiocom, against manufacturing defects in materials or craftsmanship over a period of 2 years counting from the date of original purchase for final costumer. The original receipt of purchase is mandatory for warranty validation purposes, and the product must have been bought from a NEXT Audiocom authorized dealer. The warranty can be transferred to a subsequent owner during the warranty period, however, this cannot extend the warranty period beyond the original warranty period of two years from the original date of purchase stated on the NEXT Audiocom’s invoice. During the warranty period NEXT Audiocom will, at its own discretion, either repair or replace a product which prove to be defective provided that the product is returned in its original packaging, shipping prepaid, to an authorized NEXT Audiocom service agent or distributor. NEXT Audiocom cannot be held responsible for defects caused by unauthorized modifications, improper use, negligence, exposure to inclement weather conditions, act of God or accident, or any use of this product that is not in accordance with the instructions provided by this manual and/or NEXT Audiocom. NEXT Audiocom is not liable for consequential damages. This warranty is exclusive, and no other warranty is expressed or implied. This warranty does not affect your statutory rights.
CORRECT DISPOSAL
When the speakers are to be definitively discarded, take the product to a local recycling plant for a disposal which is not harmful to the environment. This equipment should not be treated as general household waste.
Devices marked with this symbol must not be disposed of as household waste. For more information, please contact your retailer or local authorities.
TECHNICAL SPECIFICATIONS
- Product Type: Professional PA System
- Frequency Response (-6dB): 40Hz – 19kHz
- Nominal Coverage: 50-100°H x 55ºV (User Rotatable)
- Amplifier Technology: Class D with DSP
- Total Amplifier Power: RMS: 1000W | PGM: 2000W
- Maximum SPL (Calculated):
- Subwoofer: 127dB | Satellite: 121dB
- SW Driver: 15″ Woofer | 3″ Voice Coil
- LF Driver: 8″ Woofer | 1.5″ Voice Coil
- HF Driver: 1.4″ Driver | 1.35″ Voice Coil
- Input Connectors: 2 x XLR / TRS Combo
- Output Connectors: 2 x XLR
- Construction: Plywood with Polyurea Coating
- Grille: Powder Coated Steel Grille with Acoustical Foam
- Protections: Overload and overcurrent
- Power Supply: AC 115V | 230V 50Hz/60Hz
- Power Consumption: 280W (1/8 Max. Power)
- Subwoofer Net Weight: 27.5kg (60.6lb)
- Subwoofer Shipping Weight: 31kg (68.34lb)
- Satellite Net Weight: 27.5kg (60.6lb)
- Satellite Shipping Weight: 31kg (68.34lb)
TECHNICAL DRAWINGS
Dimensions in milimeters
Rua da Venda Nova, 295 | 4435-469 Rio Tinto, Portugal
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>