SAMSUNG ELECTRONICS ML60-001 BLE Transceiver for Vacuum Cleaner Stick Networks User Manual

User Manual of ML60-001

Introduction

The ML60-001 is a BLE Transceiver for Vacuum Cleaner Stick networks.
Connected to the Vacuum Cleaner Stick, it acts as a pathway between remote home automation.
Power is provided by External 3.3V power supply from Bottom PAD.
Networking
The ML60-001 is applied RTL8762CMF BLE Transceiver of Realtek.
The BLE transceiver delivers the information received from the remote control device to the main board from Bottom PAD.
Power source
The ML60-001 is powered by an external 3.3V from Bottom PAD.
Expansion Ports
34pin of Bottom PAD connects the main control board.
Indication
None.

Notice FCC/IC Statement

Approval Statement
FCC Compliance Statement
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
• The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module.
• The module is limited to installation in mobile or fixed applications.

IC approval
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC/IC RF exposure statements:
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be colocated or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:

1. This module may not be co-located with any other transmitters or antennas.
2. The antenna must be installed such that 20cm is maintained between the antenna and users.

As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements with this module installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product including this module and obtaining separate FCC & IC authorizations.

User Information

Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment.
IMPORTANT NOTE FOR OEM INTEGRATOR
This is single module which has been tested and complied with Part 15.247,and RSS-247 requirements. Host device needs to be labeled with module’s FCC/IC IDs, for example, “Contains Transmitter module FCC ID: A3LML60001 IC: 649E- ML60001”. This device is intended only for OEM integrators under the following conditions:

1. This module may not be co-located with any other transmitters or antennas.
2. The antenna must be installed such that 20cm is maintained between the antenna and users.
3. Only the antenna type and antenna gain documented in the module FCC/IC reports can be used.

As long as above conditions are met, further test or certification will not be required. However, the OEM integrator is still responsible for host product evaluation or any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations. 5)Additional testing, Part 15B disclaimer This module only complied with FCC 15.247 requirements as listed on the grant, and therefore, the host product manufacturer is responsible for FCC Part 15B compliance testing with the module installed.

Supplemental User’s Manual
INTEGRATION INSTRUCTIONS per FCC KDB 996369 D03, Section 2.0
2.2 List of applicable FCC rules
The module has been certified for use under FCC Part 15.247 only
2.3 Summarize the specific operational use conditions
The host device must be tested for spurious emissions due to the module’s lack of its own shielding.
2.4 Limited module procedures
The host device must be tested for spurious emissions due to the module’s lack of its own shielding.
2.5 Trace antenna designs
Antenna is integrated into module and the module should be used with no other antennas
2.6 RF exposure considerations
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter device. 2.7 Antennas Antenna is soldered on the module and and the module should be used with no other antennas.
2.8 Label and compliance information
Module contains its own label
2.9 Information on test modes and additional testing requirements
None required.
2.10 Additional testing, Part 15 Subpart B disclaimer
This module has been tested and certified to comply with FCC Part 15C requirements. The host device to which it is installed may require additional testing to show compliance with FCC Part 15B requirements.
Supplemental User’s Manual
INTEGRATION INSTRUCTIONS per FCC KDB 996369 D03, Section 2.0
Notice:
OEM should include the following warnings on the label:
“Contains FCC ID:****, IC Number:****”
As well as the model name:
“*****”
Installer should include the following in the user’s manual:
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
“Changes of modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>