clou CL-07.66.209.55 Hammock Dresser Installation Guide

clou CL-07.66.209.55 Hammock Dresser

IMPORTANT INFORMATION

• Before starting the installation, check whether the delivery is complete. At the same time the delivery should be checked for damage due to transportation, damage reports that are too late (> 1 day after delivery) will not be accepted.
• The included fixing media are suited for plastered or tiled solid walls with enough supporting power. For other walls the used fixing media is at own responsibility, and the wall might need reinforcement.
• Clou b.v. reserves the right to introduce technical and visual changes with respect to the depicted images.
• Due to changes in production it is possible that given dimensions are no longer correct. All mentioned dimensions in this manual should be verified before executing the action.
• Clou b.v. can not be held responsible for the results of improper use, improper transportation or any damage caused during interim storage.
• The current terms of guarantee are always valid.
• The installation has to be preformed by at least 2 persons of whom at least one should be a skilled professional.
• All dimensions are in mm.

Content of delivery

Required tools

SAFETY PRECAUTION

During installation one has to prevent damaging the surface of the product due to placing hard objects on the product.

User’s instructions :

See also the maintenance guides at www.clou.nl

DIMENSIONS

Spare parts

The drawer front is also available separately in the following finishes: Pearl oak HPL (CL/07.66.309.60), ottawa pine HPL (CL/07.66.309.61) & verona oak HPL (CL/07.66.309.61).

INSTALLATION INSTRUCTIONS

1. Mark with pencil and level the centreline of the dresser.
   

2. Measure distance Y1 from the top of the sink to the top of the dresser.
   

3. Mark with pencil and level the prefered height Y2 of the dresser. (recommended: Y2 = 900 mm – Y1)

4. Mark with pencil the spots to drill holes. It is recommended to verify the given dimensions.
   

5. Drill the holes for the supports (ø 10 mm).
   

6. Insert the dowels in the holes and mount the mounting plates with the screws.
   

7. Remove the drawer by pulling it forward and upward. Also remove the plastic covers on the sides.
   

8. Place the mounting brackets of the dresser over the mounting plates
   

9. Adjust the position of the dresser.
   With bolt A you regulate the height of the dresser, with bolt B you adjust the distance to the wall.
   

10. If applicable, connect the dressers (not for open drawer 400). At both dressers, drill the blind hole at the front. Connect with the bolt and sleeve.
    

11. Slide the plastic covers back over the mounting plates.
    

12. Mount the washbasin or countertop in accordance with its instructions on the furniture with silicon paste for sanitary. Attention: mount the remaining furniture first.
    

13. Place the drawer back in the dresser
    

14. Adjust the inclination by turning the setscrew. Make sure the drawer front is perfectly vertical.
    

15. Adjust the height of the door by turning the back screw. Do this on both sides.
    

16. Adjust the sideways placement of the door by turning the front screw. Do this on both sides
    

17. Adjust the frontal placement of the door by turning the screw on the bottom of the dresser. Do this on both sides
    

18. Replace or move all the plastic covers back in place.
    

19. Make sure all seams between dresser, countertop, washbasin and wall are sealed with silicon paste for
    sanitary
    

CUSTOMER SERVICES

Clou. Bath findings
Clou bv Thermiekstraat 1
NL -6361 HB Nuth
T +31 (0)45 524 56 56
[email protected]
www.clou.nl
Looking for inspiration?

References

• Clou bath findings - Sanitair voor design badkamers

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>