BESNOOW S1 Bluetooth Speaker User Manual

S1Bluetooth Speaker
User’s Manual

Package List

Outline Picture and Function Description

1. Type C charging port
2. USB in port
3. 3.5mm Aux input
4. Power On/Power off/Play/Pause
5. volume +/Next Song
6. FM mode
7. volume -/Previous Song
8. Light mode
9. Indicator light
10. Type-C Charging Cable
11. 3.5mm Audio Cable
12. 3.5mm FM Antenna

Using Your Speaker

1. Turn on/off
   Functional status| Key operation| Voice prompts
   ---|---|---
   On| Press and hold for 3 seconds| Power on
   Off| Press and hold for 3 seconds| Power off

2. Bluetooth Pairing
   After turning on the speaker, turn on the bluetooth on the mobile phone and search for Si, and make a Bluetooth connection to pair successfully.
   Note: When turned on, Si will automate-cally connect to the last connected device if available.

3. Speaker Charging
   Functional status| Indicator light| Voice prompts
   ---|---|---
   Low battery| Flashing red| Battery low
   Charging| Steady red|
   Fully charged| Red light off|
   Note: To preserve battery lifespan, fully charge at least once every 30 days

4. Connect via AUX
   Plug in the 3.5mm audio cable, connect to mobile phones/computers/ tablets and so on, it can be used as external speakers.
   Note: To return to Bluetooth mode, remove the AUX cable from your S1 speaker.

5. FM Mode
   Plug in the 3.5mm FM antenna in the “AUX”, then press the FM Button once to switch to FM radio(Voice prompt “FM mode”) and then press the power button to search for channels.
   Note: Press the FM Button again to switch the Bluetooth function(Voice prompt “Blue-tooth mode”)

6. Light Switch Mode
   Press the light button to switch the flashing mode of the magic light. There are 7 light modes in total.

Button Controls

1. For Music Control Operation Table
   | Button| Key operation
   ---|---|---
   Play/Pause| | Press
   Volume +| | Press
   Volume –| | Press
   Next song| | Press and hold
   Previous Song| | Press and hold
2. For Bluetooth Calling  Operation Table
   Answer/end call| | Press
   ---|---|---
   Reject call| | Press and hold

Technical Specifications

Safety Information

Do not use corrosive cleaners to clean this product.
Do not heat up or place this product near a source of fire
Do not expose this product to direct sunlight for an extended period of time.
Do not dispose of this product in a fire to avoid explosions.
Do not attempt to dismantle this product for any modifications.

Activation & Warranty

Please follow up on the user’s manual step-by-step and we will always stand by if you have any problems while playing S1 speaker. If you have any other ques- tions, please contact us.
Activate Permanent After-sales Service: Permanent replacement of damaged, defective, not upgraded, or missing items (no need to return the original)Please activate via email below within 15 days.
Our Customer Service Email : yefan1357@gmail.com
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>