FLebi SWAN 24 Inch Touring Electric Bike User Manual

FLebi SWAN 24 Inch Touring Electric Bike

Product Information

The Flebi Swan 24 is an electric bike powered by a 36V / 250W motor. It has a top speed of 25 km/h. The bike comes with an integrated battery in the frame and includes a battery charger.

Unpacking and Assembly

1. Take the Swan 24 out of the box.
2. Remove the guards.
3. Unfold the bike.
4. Insert the handlebar assembly.
5. Fit the seat post to the frame.

Check the contents of the box to ensure you have the Flebi Swan 24 bike with the integrated battery and the battery charger.

For visual instructions, you can refer to this video.

Handlebar Assembly Introduction

To install the handlebar and telescopic seatpost assembly, you must insert it into the stem before placing it in its natural position. Follow the guides provided. Ensure that the cables go down cleanly and tighten the locking key firmly.

For visual instructions, you can refer to this video.

Packing in Original Box

If you need to repack your bike in its original box, follow these steps:

1. Cover the parts with protection.
2. Remove the seat post.
3. Remove the handlebar assembly.
4. Fold the bike.
5. Put it in the box.
6. Place the cork fixing the front wheel.
7. Place the pedal on a guard.
8. Place the front folding lever inwards.
9. Insert the rest of the accessories and seal the box.

For visual instructions, you can refer to this video.

Handlebar Adjustment

You can adjust the height of the handlebars to suit your height. Open the telescopic lock and place the seat post in the desired position, taking care not to exceed the safety mark. Then tighten the lock firmly. This adjustment can also be used to correct slight deviations in the direction of the bike. Open the lock, turn the handlebars to the left or right to find the correct alignment, and retighten the lock.

For visual instructions, you can refer to this video.

Saddle Adjustment

You can adjust the saddle height to suit your height. To adjust the hardness, tighten the thread according to your preference. Make sure it is not too loose, or the seat post will move. To change the angle of the saddle, use a number 13 spanner to set the saddle angle. Remember to tighten it well.

For visual instructions, you can refer to this video.

Brake Adjustment

The brakes on Flebi bikes are fully adjusted at the factory, so no adjustment is necessary unless they become loose with use. If you need to adjust the brake calipers on your Flebi Swan 24, you have two types of adjustment: for brake force and alignment. To adjust the force, adjust the pad on the outer face by cable tension. For the inner side, access it from the opposite side to bring the pad closer.

Unpacking and assembly

1. Contents of the box

2. Introduction of the handlebar assembly

3. Packed in original box
   Start-up

4. Handlebar adjustment

5. Saddle adjustment

6. Brake adjustment

7. Tyre inflation
   Electrical operation

8. Recharging the battery

9. Operation of the EN067 display
   Folded & unfolded

10. Unfolding the ebike

11. Folding the ebike

12. Opening and closing the frame

13. Folding and unfolding the pedals

14. Handlebar folding mechanism

Contents of the box

• The assembly of your Flebi Swan 24″ is very easy and fast!
  Flebi Swan 24″ is powered by a 36V / 250W motor and has a top speed of 25 km/h.

• Take your Swan 24″ out of the box -Remove the guards

• Unfold the bike

• Insert the handlebar assembly

• Fit the seat post to the frame
  Check the contents of the box:

• Flebi Swan 24″ bike with battery integrated in the frame

• Battery charger

Introduction of the handlebar assembly

To install the handlebar and telescopic seatpost assembly that allows you to adjust the height, you must insert it into the stem before placing it in its natural  position, following the guides that youwill find. Check that the cables go down cleanly and remember to tighten the locking key firmly.

Packed in original box

If you need to repack your bike in its original box to send it to Flebi service, we recommend that you follow the steps below:

• Cover the parts with protection
• Remove the seat post
• Remove the handlebar assembly
• Fold the bike
• Put it in the box
• Place the cork fixing the front wheel
• Place the pedal on a guard
• Place the front folding lever inwards
• Insert the rest of the accessories and seal the box.

Handlebar adjustment.

You can adjust the height of the  handlebars to suit your height. To dothis, open the telescopic lock and place the seat post in the desired position, taking care not to exceed the safety mark. Then tighten the lock firmly so that it does not move. You can also use this same adjustment to correct slight deviations in the direction of the bike. Open the lock, turn  the handlebars to the left or right to findthe correct alignment, and retighten the lock .

Saddle adjustment.

You can also adjust the saddle height to suit your height. To adjust the hardnessyou must tighten the thread according to your taste. Make sure it is not too loose or the seat post will move. To change the angle of the saddle, you can use a number 13 spanner to set the saddle angle. Remember to tighten it well.

Brake adjustment

CAUTION: The brakes on all Flebi bikes are fully adjusted at the factory and no adjustment is necessary unless they become loose with use. If you need to adjust the brake calipers on your Flebi Swan 24″, you have two types of adjustment: for brake force and alignment. To adjust the force, the pad on the outer face is adjusted by cable tension. For the inner side, you have to access from the opposite side to bring the pad closer.
Ideally, this should be done a little at a time, to test if it brakes cleanly .

Tyre inflation

To check the amount of air in the tyres, remember that the Swan 24″ carries between 2.5 and 4.8 bar of pressure, so it is advisable to use an inflator with a pressure gauge. The pressure will vary depending on the terrain you are riding on.

Recharging the battery

The battery of Swan 24″ is inside the frame but can be removed from the frame for convenient charging. The charging point is located on the left side of the frame, under a rubber cover that must be removed to access the connector. The LED light on the charger will turn red indicating that it is charging, until it is fully charged (about 4 hours), when it will turn green, indicating that you can disconnect.

Operation of the EN067 display

The EN067 display is operated by pressing the power button on the bottom left of the display. Right next to it are the + and – buttons to increase or decrease the assistance level. When switched on, the display shows the km/h, the assistance levels and the remaining battery. At level 0 you will not enjoy any pedal assistance and at level 5 the assistance will be the highest. To activate the electric assistance, all you have to do is pedal and the motor will assist you with the selected level of assistance (use the +/- buttons to move between them).

Unfolding the ebike

The steps to unfold your Flebi Swan 24″ are very simple:.

• Lift the bike and unfold the frame, tighten the central lock and place the lock.
• Unfold the pedals
• Lift the stem off the handlebars, close the folding lever and insert the safety catch

Folding the ebike

The steps to fold your Flebi Swan 24″ are very simple:.

• Lower the handlebars
• Release the central locking mechanism of the frame
• Fold the pedals
• Open the frame and bring it to the folded position
• The bike rests on the lower stand

Opening and closing the frame

To open or close the frame, you only have to remove the lock in the central part in case of opening and put it on in case of closing.

Folding and unfolding the pedals

Install the pedals of your Flebi Swan 24″ very easily with this tutorial. To fold or unfold each pedal you must press the knob outwards and, at the  same time, fold the pedal inwards (folded) or outwards (unfolded) until you feel the lock.

Handlebar folding mechanism

First of all, make sure that the cables are not tangled or too tight due to the set handlebar height. You can adjust the height and inclination of the handlebars. The bike has an indicator on the inside of the handlebars to show the maximum height. In addition, you can tilt the handlebars and grips for your comfort.

• @ flebi_bikes
• fflebikes
• @flebikes
• www.flebi.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>