DS18 IXS12.4D Bronco 6th Gen Tailgate 12 Subwoofer Enclosure Owner’s Manual

June 12, 2024
DS18

DS18 IXS12.4D Bronco 6th Gen Tailgate 12 Subwoofer Enclosure

DS18-IXS12.4D-Bronco-6th-Gen-Tailgate-12-Subwoofer-Enclosure-
product

12″ PORTED ENCLOSURE WITH IXS12.4D SHALLOW SUBWOOFER AND GB LED GRILLE FOR 6TH GEN FORD BRONCO TAILGATE

  • Ported / Ventilated Box Design for High Output
  • IP11 Water Resistant Material for Light Rain
  • Exclusive DS18 Design with RB LED Lighting
  • 5ft / 1.5m (6 core) Wiring included for Speaker and GB LED
  • 12″ DS18 IXS12.4D Subwoofer Included
  • Easy to install using factory locations and hardware included
  • GB LED Controller (optional) not included.
  • Aftermarket Amplifier required not included

INSTALLATION & CONNECTION OPTIONS

If you have an LED Control Module (LED-BTC), Connect as Shown in the

Following Diagram:

DS18-IXS12.4D-Bronco-6th-Gen-Tailgate-12-Subwoofer-Enclosure-
fig-1

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

  • Black wire”BK” connected to battery Positive + 12V
  • White Color Light “R”; “B” and “G” connected to battery Negative (-)
  • Green Color Light “G” connected to battery Negative (-)
  • Red Color Light “R” connected to battery Negative (-)
  • Blue Color Light “B” connected to battery Negative (-) Purple Color Light “R” and “B” connected to battery Negative (-)
  • Yellow Color Light” R” and “G” connected to battery Negative (-)
  • Cyan Color Light “B” and “G” connected to battery Negative (-)

DS18-IXS12.4D-Bronco-6th-Gen-Tailgate-12-Subwoofer-Enclosure-
fig-2

INSTALLATION

Follow these easy steps to install your BRO-BASS: Start with removing the ford plastic door cover to access the anchor points. use a rivet nut gun to secure the anchor nut provided to the door at the points shown in the image. Then remove the Grill that protects the speaker by pulling firmly. It has a pressure anchoring system, be aware of the GB light cable, disconnect it and put the grill in a safe place. Remove the subwoofer by removing the 8 screws holding it in and then disconnect the wires on the back so you have access to the inside of the box. Use the supplied M6 screws to secure the box with the tailgate, tighten firmly. Now you can install the subwoofer back and secure it, put the grill back and don’t forget to connect the RGB lights back. Doing this you will finish the installation of your BRO-BASS.

Recommendation:
Check with your favorite dealer or Audio shop for the installation of an aftermarket amplifier to power-up this subwoofer.

DS18-IXS12.4D-Bronco-6th-Gen-Tailgate-12-Subwoofer-Enclosure-
fig-3

GENERAL

  • Speaker Size   ….. 12″ / 304mm
  • Total Impedance …….2 Ohms
  • Total RMS Power Handling ….800W
  • Total MAX Power Handling ….. 1600W
  • Sensitivity (1w/1m)   ……………………………. 906B
  • Frequency Response ……………….0 Hz-200Hz
  • Recommended Lo Pass Crossover ……………..80Hz

FEATURES

  • Ported Box for High Output …………………….. Yes
  • Water Resistant Materials for Light Rain …………………………………………… Yes (IP11)
  • Exclusive Ford Bronco Design ……. Yes
  • Injected Molded ABS Grill with Built-in RGB LED Lighting ……. Yes
  • Input Wires for RGB LED and Subwoofer …………Yes, 5ft / 1.5m (6 Cores)
  • Subwoofer Included ………Yes, 12″ (IX512.4D)
  • Installation Hardware Included ……………..Yes, 3 x 6M screws
  • Easy to Install …………… Yes, fits on the tailgate and secures using the factory bolt location

SUBWOOFER SPECIFICATIONS

  • Voice Coil Diameter …… 2.5 / “63.5mm
  • Voice Coil Former Material …………… Aluminum
  • Winding Material ….. Copper
  • Cone Material   ………. Paper
  • Dust Cap Material ……………. fiberglass
  • Surround Material …….. Stitched Rubber
  • Basket Material ….. Aluminum
  • Magnet Material ………Ferrite
  • Magnet Weight ……………. 62 Oz

BOX SPECIFICATIONS

  • Internal Volume 34L / 1.2ft3
  • Port Tune 45Hz
  • Load Configuration Parallel
  • Box Type Front Loaded Ported
  • Box Material Polyethylene (PE)
  • Finish Material Black
  • -3dB Dropping Point 36Hz

MEASUREMENTS

  • Overall Height 17.81″ / 452.3mm
  • Overall Width 27.4″ / 695.6mm
  • Overall Depth 7.4″ I 188mm

DS18-IXS12.4D-Bronco-6th-Gen-Tailgate-12-Subwoofer-Enclosure-
fig-4DS18-IXS12.4D-Bronco-6th-
Gen-Tailgate-12-Subwoofer-Enclosure-fig-5

WARRANTY

Please visit our website D518.com for more information on our warranty policy. We reserve the right to change products and specifications at any time without notice. Images may or may not include optional equipment.

WARNING: Cancer and Reproductive Harm. www.P65Warning.ca.gov

FOR MORE INFORMATION PLEASE VISIT DS1S.COM

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

DS18 User Manuals

Related Manuals