Mr Christmas 68325 7.5ft RGB Christmas Tree Flocked Instruction Manual

Mr. Christmas
7.5ft RGB Christmas Tree
Flocked, Item # 68325
Instruction Manual
FOR INDOOR USE ONLY

Step 1: Check the contents of your box

Before starting assembly, be sure to check all contents and lay out the various tree parts accordingly. There are:
A. Top tree section.
B. Middle tree section
C. Bottom tree section.
D. Control box and power cord with adaptor.
E. Tree stand.
F. Three pins for the tree stand.
G. “Ornament” with the voice-activated command list
H. Spare bulbs: 10 pieces (in the polybag attached to the end of the light strand inside the tree).

Step 2: Expand Stand

1. Take the tree stand and pull apart the legs (Figure A), open to full Position (Figure B)
2. Take the fully opened tree stand and insert pins into the pre-drilled holes, tightening the pins part way (complete tightening in Step 3-1).

Step 3-1: Tree Assembly

1.  Take the tree section labeled “C” and insert it on the top of the tree stand. (Figure A)
2. Fully tighten the 3 pins into place (Figure B). Secure the tree base firmly to the tree stand.

Step 3-2: Tree Assembly

Take Tree Section labeled “B” and insert it into the top of the pole of section “C”.

Step 3-3: Tree Assembly

Take the tree section labeled “A” and insert it into the pole into the top of the pole of section “B”.

Step 4: Connect to AC Power

Attach the power cord with an adaptor to the control box, and plug the adaptor into an AC power source.

Step 5: Connect to Alexa

1. Download the “Amazon Alexa” application from the app store on your mobile device.
2.  Install and open the “Amazon Alexa” application.
3. Go to the settings menu.
4. Select “Add Device”
5. Select “Christmas Tree” and follow the on-screen instructions.
6. To set up a second tree, select “Second Christmas Tree” and follow the on-screen instructions. Alexa will ask for clarification if a command does not target a specific tree.

Barcode Scanning & Location Note that during device setup you may be asked to scan a device barcode. You can find this on the back of the controller, shown in Figure A.``

Step 6-A: Change your Christmas Tree LED lighting Mode using Alexa

Follow the voice commands for a list f functions to achieve up to 40 lighting functions.

Color options Command – “Set Christmas tree to”

1. Red
2. Green
3. Yellow
4.  Blue
5. Purple
6. Light Blue
7. White
8. Multi-Color

| Lighting functions Command – “Set Christmas tree to” :
a. STEADY
b. SPARKLE
c. FIREFLY
d. FLIP
e. FADE
---|---

Step 6-B: Manually change your Christmas Tree LED lighting mode

Push the Button on Control Box to switch to Christmas Tree LED Light Mode. There are a total of 40 lighting modes:

Demo Mode is available: Press and hold the button on the control box of the tree for 3-4 seconds. The tree lights will turn green and will flash 3 times This indicates that the instructions were received. The Demo mode will start and play all 40 lighting functions.

Step 6-C: Automate your Christmas Tree with Routines

Alexa Routines allow you to automate your Christmas Tree Functionality. With Routinesyou can turn your tree on with custom commands (i.e. Good Morning) or turn the tree
on/off at scheduled times (i.e. every day at 10 AM)
How to Enable Routines with Alexa.

1. Open the Alexa app.
2.  Go to the menu and select “Routines”
3. Select Plus
4. Select “When this happens”, and then choose how to begin your Routine (i.e. “Good Morning, or a scheduled time).
5. Select “Add Action”, select “Smart Home”, and then select “Christmas Tree”. Configure the desired LED lighting mode for your selected action.

|
---|---
|

Connectivity Troubleshooting

Common connectivity troubleshooting steps.  I can’t connect my device to Alexa. Reset your tree
To reset your Alexa Tree: press and hold the button on the control box for 10 seconds. Indication of
action done: 3 flashes of white light. Then follow the instructions below.
a) Download the “Amazon Alexa” application from the app store on your mobile
device.
b) Install and open the “Amazon Alexa” application.
c) Go to the settings menu.
d) Select “Add Device”
e) Select “Christmas Tree” and follow the on-screen instructions.

• Check your WIFI settings
• Make sure that your Alexa device and your Christmas Tree are connected to the same Wi-Fi network.
• Make sure that all devices have the most updated Wi-Fi password.
• Check the distance to your Alexa smart speaker
• Check that your device is within 30 ft. (9 m) of your Christmas Tree.
• Check your software version
• Check that your Alexa device and the Alexa app have the latest software version.

Connectivity Troubleshooting

Common connectivity troubleshooting steps.
I can’t get my Christmas Tree barcode to scan successfully.
Make sure that there is enough light in the area for the bar code to be detected.
If that does not work, then during the Alexa mobile app setup process, select “Don’t Have
a Barcode” and follow the on-screen instructions.
My Christmas Tree stopped working with Alexa.

• Try a power cycle: Unplug your Christmas Tree from the outlet, and then plug it back in.
• Perform a factory reset: To reset your Alexa Tree: press and hold the button on the control box for 10 seconds. Indication of action done: 3 flashes of white light. Then follow the instructions below.
• Download the “Amazon Alexa” application from the app store on your mobile device.
• Install and open the “Amazon Alexa” application.
• Go to the settings menu.
• Select “Add Device”
• Select “Christmas Tree” and follow the on-screen instructions.

Connectivity Troubleshooting

Common connectivity troubleshooting steps.
I can only turn my Christmas Tree On and Off with Alexa.

• Although the Alexa tree can be added to a group, the color and function selections will not work using the group name.
  Color and Function can only be selected by using the utterance “Christmas Tree.”
  Alexa is not responding to some but not all of my utterances

• Alexa will not work if you have more than one Alexa device with a similar name

• Rename one of the devices.

It is recommended to always store the tree in a cool, dry location protected from excessive exposure to heat or sunlight.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be followed including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided contact a qualified for proper installation.
c) This seasonal use product is not intended for permanent Installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles, or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
f) Do not let bulbs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury, and electric shock it should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from the cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation
l) Do not cover the product with cloth, paper or any material not part of the product when In use.
m)This product is equipped with push-in type bulbs. Do not twist bulbs.
n) Read and follow instructions that are on the product or provided with the product.
o) Save these instructions.

User Servicing Instructions
Replace the bulb.

1.  Grasp plug and remove from the receptacle or other outlet
   device. Do not unplug by pulling on the cord.

2. Pull bulb and plastic base straight out of bulb holder

3. Replace bulb with only 3 Volt 0, 06 Watt LED type bulb (provided with product).

If the new bulb base does not fit in the bulb holder, follow the steps below before step 3.
a) Remove the base of the burned-out bulb by straightening bulb leads and gently pulling the bulb out.
b) Thread leads of the new bulb through holes In the old base with one lead in each hole.
c) After the bulb is fully inserted into the base, bend each lead-up like other bulbs in the light set. so that the leads will touch the contacts inside the bulb holder.
CAUTION

1. To reduce the risk of fire or electric shock do not attempt to replace bulbs or modify the string.
2. To reduce the risk of fire and electric shock： a) Do not install on trees needles, leaves or branch coverings of metal or materials that look like metal, and b) Do not mount or support strings in a manner that can cut or damage wire insulation.

Model No: 68325
Made by Mr. Christmas Inc.
6045 E. Shelby Dr., Suite 2, Memphis, TN 38141-7601
customerservice@mrchristmas.com
Customer service number: 1-800-453-1972
Made in China

Documents / Resources

| Mr Christmas 68325 7.5ft RGB Christmas Tree Flocked [pdf] Instruction Manual
68325, 7.5ft RGB Christmas Tree Flocked, Christmas Tree Flocked, Tree Flocked, 68325, Flocked
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>