VIXEN HORNS VXS-2245AR 220V Industrial Electric Motor Siren Installation Guide
- June 13, 2024
- VIXEN HORNS
Table of Contents
VIXEN HORNS VXS-2245AR 220V Industrial Electric Motor Siren
Product Information
- Product Name: VXS-2245AR Industrial Electric Motor Siren (Red)
- Voltage Requirement: 220-240 volt AC
- Safety Instructions:
- This product produces a very loud sound, improper use may result in hearing loss or permanent damage.
- Do not operate in a closed environment or near pedestrians.
- Do not connect the siren to any power source other than 220-240 volts AC.
- Use eye protection equipment during drilling operations.
- Do not connect the siren if supply wires are energized.
- Mounting Instructions:
- Identify a suitable area for mounting, preferably an unobstructed steady surface like a pole.
- Do not attach the siren to a flexible material.
- Use the bracket as a guide to estimate and mark the positions for the holes.
- Perforate the marked positions using a drill.
- Secure the siren to the surface using four screws (not provided).
- Electrical Connections:
- Before starting with any electrical connections, ensure that the supply wires are not energized.
- Connect the RED wire of the siren to the PHASE lead of your 220-240V AC power source.
- Connect the BLUE wire of the siren to the NEUTRAL lead of your 220-240V AC power source.
- The connections of the red and white wires can be switched, red wire can be connected to the neutral lead and white wire to the phase lead.
- Unscrew the small screw located in the siren’s body to connect the GROUND lead and tighten the screw.
- If you want to activate the siren manually, your power source must have a switch installed.
- If the siren is being used as part of a smoke detector, gas sensor, timer, or anti-theft alarm system, please follow your device’s instruction.
- Maintenance:
- Other than cleaning, no maintenance is required.
- To ensure the siren is operating properly, it should be tested frequently.
Product Usage Instructions
- Read through the entire instruction guide before starting with the installation.
- Professional installation is recommended for this product.
- Ensure you have an AC power source of 220-240 volts for installation.
- Choose a suitable mounting location, preferably an unobstructed steady surface like a pole.
- Do not attach the siren to a flexible material.
- Use the bracket provided as a guide to estimate and mark the positions for the holes.
- Perforate the marked positions using a drill.
- Secure the siren to the surface using four screws (not provided).
- Ensure that the supply wires are not energized before starting with any electrical connections.
- Connect the RED wire of the siren to the PHASE lead of your 220-240V AC power source.
- Connect the BLUE wire of the siren to the NEUTRAL lead of your 220-240V AC power source.
- The connections of the red and white wires can be switched if necessary.
- Unscrew the small screw located in the siren’s body to connect the GROUND lead and tighten the screw.
- If you want to activate the siren manually, ensure that your power source has a switch installed.
- If you are using the siren as part of a smoke detector, gas sensor, timer, or anti-theft alarm system, follow the instructions provided with your device.
- No maintenance is required other than cleaning.
- Test the siren frequently to ensure it is operating properly.
BEFORE BEGINNING YOUR INSTALLATION
- Read through the entire instruction guide before getting started with the installation. Professional installation is recommended for this product.
CONTENTS
- 220V Industrial Electric Motor Siren (Red)
The specific voltage requirement for this siren is 220-240 volt AC. Therefore installation must be done with an AC power source of 220-240 volts.
SAFETY INSTRUCTIONS
- This product produces a very loud sound, hearing loss or permanent damage may result from improper use.
- Do not operate in a closed environment or near pedestrians.
- Do not connect the siren to any power source other than that specified above.
- Employ equipment for eye protection during drilling operations.
- Do not connect if supply wires are energized.
MOUNTING
- Identify a suitable area for mounting, preferably an unobstructed steady surface like a pole. Do not attach the siren to a flexible material.
- Using the bracket as a guide estimate and mark the positions for the holes and then perforate to size using a drill.
- Secure the siren to the surface using four screws (not provided).
ELECTRICAL CONNECTIONS
WARNING: Before starting with any electrical connections make sure the supply wires are not energized.
- Connect the RED wire of the siren to the PHASE lead of your 220-240V AC power source.
- Connect the BLUE wire of the siren to the NEUTRAL lead.
IMPORTANT: The connections of the red and white wires can be switched, red wire can be connected to neutral lead and white wire to phase lead.
- Unscrew the small screw located in the siren’s body to connect the GROUND lead and tighten the screw.
- To activate the siren manually your power source must have a switch installed.
- If the siren is being used as part of a smoke detector, gas sensor, timer or anti-theft alarm system, please follow your device’s instruction.
MAINTENANCE
- Other than cleaning, no maintenance is required.
- To ensure the siren is operating properly, it should be tested frequently.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>