VIXEN HORNS VXO8330BDP-8124XB 8 Black Trumpets-3 Gallon Tank-200 PSI Compressor Train Horn Kit Installation Guide

VIXEN HORNS VXO8330BDP-8124XB 8 Black Trumpets-3 Gallon Tank-200 PSI Compressor Train Horn Kit Installation Guide

CONTENTS

• Octo Trumpet Train Air Horn (Black)
• 200 PSI Air Compressor (Black) x 2
• 3 Gallon Air Tank
• 12V Electric Air Valve (Solenoid)
• 240 PSI Air Pressure Gauge
• 170-200 PSI Pressure Switch
• 250 PSI Safety Valve
• 1/4″ NPT Wing Style Drain Valve
• 1/4″ NPT Compression Fitting for 1/4″ OD Air Line
• 1/4″ NPT Compression Fitting for 3/8″ OD Air Line
• 1/4″ NPT Hex Head Male Plug
• 1/2″ NPT Hex Head Male Plug
• 3/8″ OD Nylon Plastic Hose (25 Feet)
• 12mm Thread Sealant Tape (16 Feet)
• 5-PIN 12V/40A Relay with Pre-wired Plug x 2
• 30A In-line Fuse with Waterproof Holder x 2
• 60A In-line Fuse with Waterproof Holder
• Remote Mount Air Filter x 2
• Horn Button
• Mounting Hardware

The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts.

SAFETY INSTRUCTIONS

• Do not attempt to disassemble, repair or customize this product.
• Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water.
• Avoid reaching out to touch or pick up any fallen or water submerged parts.
• Never leave this product unattended during use.
• Intended for use by adults only.
• During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods.
• Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others.
• Avoid use of product near flames, explosive materials, aerosol products or oxygen devices.
• Be sure to pump nothing other than atmospheric air.
• It is important to determine the maximum air pressure for any tool or attachment before using it.
• Air sprayer or nozzle should always be pointed away from any part of the body.
• The compressor has Thermal Overload Protection, if this protection activates, cut  off the source of power and letthe unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor.
• Make sure your battery ground is detached before you begin.
• Set the horn up for use only in areas with adequate ventilation.
• Employ equipment for eye protection during drilling operations.
• Ensure that your air system has no pressure before you begin.

PLANNING YOUR INSTALLATION

• Before beginning the installation, determine each component’s spot.
• Confirm you have the proper length of airline and wire.
• Power wire to compressor should be kept short.
• To power up the air compressor, make sure you use a 12-gauge wire or thicker.

HORN
MOUNTING

• Identify a suitable area for mounting, preferably an unobstructed sheet-metal surface like the frame or body of the vehicle so as to provide a firm platform which will help protect the horn from damage due to excessive shaking. Do not attach the horn to any plastic or other flexible material.
• Using the bracket as a guide estimate and mark the positions for the holes and then perforate to size using a drill.
• Use the provided mounting hardware to fasten the horn.

AIR LINE INSTALLATION

• Using the provided 3/8″ OD air line, cut the size needed.
• Push hose into the push to connect TEE fitting located in the top of the horn.
• Connect the other end of the air line to the fitting on your air supply.
• If you need to disconnect the air line from the solenoid pull away the air line while pushing the plastic part of the pneumatic fitting.
  

COMPRESSOR

MOUNTING

• Determine a dry place to mount your compressors. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around them and also to avoid heat from the exhaust. IMPORTANT: Never attach the compressors to any plastic or other flexible material.
• For optimal results, the compressors should be placed as close to the battery as possible. This will reduce the amount of wiring needed.
• Avoid placing compressors near flammable liquids.
• If you are planning to move compressor’s air intake to an area other than where the compressors were installed, make sure your placement allows for the airlines to be routed from the air inlet of the compressors to the remote inlet air filters.
• Mark the spots for the holes with the mounting base as a guide and then drill. Make sure both compressors are secured.
• To enhance performance and make sure the battery of your vehicle doesn’t discharge, keep the engine running while the compressor is being used.

BRAIDED HOSE INSTALLATION

• Connect the stainless steel braided hose of the compressor to the tank’s inlet port.
• IMPORTANT: The tank’s inlet port must be 1/4″ N.P.T. (National Pipe Thread).
  

CHECK VALVE

• The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction.
• IMPORTANT: When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor.

REMOTE FILTER

• Using a compatible remote air filter installation kit (sold separately) your compressor’s air intake can be installed in an area other than where the compressor was installed.

THERMAL OVERLOAD PROTECTION

• The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor

AIR TANK

MOUNTING

• Find a convenient mounting location in your vehicle for the air tank. Ensure ports are reachable before drilling any holes.
• Mark the location of holes using the mounting brackets of the air tank as a template, and then drill to size.
• Using mounting hardware provided, secure the air tank. IMPORTANT: Do not mount on a flexible material.
• The installation location of your tank’s accessories depends on your air system’s configuration.

PORT LOCATIONS AND THREAD SIZE (NPT)

PRESSURE SWITCH RATING

• The included pressure switch has a rating of 170 PSI ON, 200 PSI OFF. When the  air pressure in the air tank is below the preset ON pressure (170 PSI), the compressor will automatically turn on and will start pumping air into the tank. When the pressure reaches the cut OFF pressure (200 PSI), the compressor will be automatically shut off.

AIR PRESSURE GAUGE

• In one of the Air Tank’s 1/4″ NPT ports, using the thread sealant provided, install the air pressure gauge.
• The side or top of the tank is the best location to use as to prevent condensation from entering into the gauge.
• Dropping or disturbing the product can affect the product’s accuracy.
• For best results, the air gauge should be installed perpendicular to the ground, with the zero facing the bottom.
• To tighten the pressure gauge into the air tank, place a wrench over the square wrench flats to tum the gauge. This is the proper way to avoid air leakage or damage.

SAFETY VALVE

• Your system comes with a safety valve designed specifically to release pressure from the air tank automatically if 250 PSI is exceeded. This will help prevent an accident in case of pressure switch failure.

DRAIN VALVE

• This valve helps you drain the water that can collect in the air tank after long periods of use.

REMOVING CONDENSATION:

• To remove any condensation which has accumulated inside the tank, bleed the tank’s pressure until it ranges from approximately 5 PSI to 20 PSI.
• Remove the drain valve found at the tank’s bottom to drain the water from the tank. After draining the accumulated condensation, reinstall the drain valve.
• IMPORTANT: Draining the system regularly will extend the life of the air tank.

THREAD SEALANT

• Your system includes Premium Thread Sealant, make sure to use it on all thread connections to ensure proper air sealing.

ELECTRICAL CONNECTION

COMPRESSOR

• Red wire (positive) of the compressor is connected to PIN 87 on the relay. IMPORTANT: Make sure to use wire that is as heavy as the wire of the compressor
• Black wire (negative) of the compressor and PIN 85 of the relay are connected to ground.
• Repeat above steps for the second compressor.
• Connect together PIN 86 of both relays and then connect it to one of the terminal of the pressure switch. Attach the remaining terminal of the pressure switch to a power source in the vehicle that only gets power when the vehicle’s ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel. Make sure to use wire that is as heavy as the wire of the compressor.
• Connect together PIN 30 of both relays and connect it to a constant power source using the provided 60A fuse.
• Both compressors are now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, they will turn off. If compressors fails to reach the maximum air pressure of the tank, which is the Pressure Switch’s cut OFF pressure, check all air connections for leaks. While compressor are pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant.
• NOTE: To makes installation fast, trouble free and professional, this kit comes with two Pre-wired Relay Plugs (one for each relay), they will attach to the relay only in one position.

HORN (SOLENOID)
USING NEW HORN BUTTON

• Join one wire from one solenoid with one wire from the second solenoid, then connect it to the positive (+) terminal of the battery, alternator, etc. This circuit should be protected using a 20A fuse (not provided).
• Join the other wire from one solenoid with the remaining wire of the second solenoid, then connect it to one post of the horn button. The remaining connection of the Horn Button must be  connected to ground.
  

ELECTRICAL CONNECTION
USING VEHICLE’S HORN SWITCH

• First, determine the switch’s polarity. The horn of most vehicles sends a negative (-) signal which can be confirmed by connecting one of the probes from an ohm meter to the wire of the horn while connecting the other one to ground. The meter should be at zero. This proves that horn circuit is negative (-). In case the meter reads anything other than zero ohms, test for voltage between the wire of the horn and the ground. A 12-volt reading would mean a positive (+) horn circuit.
• Once you know the horn circuit’s polarity, join one wire from one solenoid with one wire of the other solenoid, then join the other wire of the solenoid with the remaining wire of the other solenoid so you have two terminals instead of four. Connect any of the two solenoid terminals to the horn wire.
• If you have a negative horn circuit, connect the remaining solenoid terminal to a constant 12-volt power source.
• If you have a positive horn circuit, connect the remaining solenoid terminal to ground.

MAINTENANCE

• Make sure that electrical and fitting connections are regularly inspected, cleaned and tightened when needed.
• Make sure mounting screws are regularly tightened if needed.
• Drain weekly, to avoid excessive buildup of condensation.
• Compressor features a washable air filter which should be cleaned using any mild form of liquid soap every two months if it gets dusty. Just remove the front cover of the filter’s housing to reach it.
• Clean dirt and dust from heat spreader and motor housing of the compressor.
• The motor of the air compressor has a maintenance-free lasting lubricant. DO  NOT LUBRICATE.

SOLUTIONS TO COMMON ISSUES

Issue: Compressor inoperable.

Solution 1: Check all switches to make sure they are ON.
Solution 2: Check the fuse; if blown, disconnect compressor from power and replace the fuse.
Solution 3: Allow compressor to cool off for 30-60 minutes.
Solution 4: Check pressure switch, replace if damaged or inoperable.

Issue: Air horn is inaudible

Solution 1: Check all switches to make sure they are ON.
Solution 2: Assure air tank is pressurized.
Solution 3: Check the fuse; if blown, disconnect compressor from power and replace the fuse.

Issue: Excessive moisture in horn or safety valve.

Solution 1: Depressurize and drain the tank.
Solution 2: Relocate the compressor to a drier location.

Issue: Continual cutting-off of Thermal overload protection.

Solution 1: Relocate the compressor to a drier, cooler location.
Solution 2: Replace the compressor.

Issue: Excessive vibration or noise

Solution 1: Tighten system components.
Solution 2: Replace the compressor.

Issue: Loss of pressure of tank when compressor is shut off.

Solution 1: Tighten drain cock.
Solution 2: Examine air and check valves and replace if damaged or leaking.
Solution 3: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Solution 4: Replace safety valve, it may be defective.

Issue: Compressors runs continuously and has low air flow.

Solution 1: Decrease the frequency of use.
Solution 2: Use soap and water solution on air connections, and tighten connections or repair leaks where needed.
Solution 3 : Clean or replace the air filter element if it is clogged.
Solution 4: Replace compressor.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>