DS18 CF-X6TPneo 6.5 Inch Neodymium Marine Towers Owner’s Manual

DS18 CF-X6TPneo 6.5 Inch Neodymium Marine Towers

Product Information

Driver and RGB LED Lights
General Specifications|

• Nominal Diameter: 6.5″
• Nominal Impedance: 4 ohms
• RMS Power Handling: 150 Watts
• MAX Power Handling: 450 Watts
• Sensitivity (1w/1m): 93 dB
• Frequency Response: 70 Hz – 21 KHz
• Recommended HI Pass Crossover: 90 Hz

Body / Features|

• Enclosure Material: Injection PC+ABS Marine Grade
• Type: IP65 + UV Stable
• RGB LED: Integrated LED-RGB Speaker Lighting

Woofer Specifications|

• Voice Coil Diameter: 1.5″
• Cone Material: Waterproof Compress Paper+Carbon Fiber
• Surround Material: Soft PC Damping Glued
• Basket Material: PC Injection Molded Composite
• Magnet Material: Neodymium
• Magnet Grade: N40H
• Passive Radiator: 3.5″ With LED RGB Light

Tweeter Specifications|

• Voice Coil Diameter: 1″
• Type: Compression Driver with CNC Solid Aluminum Horn
• Diaphragm Material: PEN
• Magnet Material: Neodymium
• Crossover: 12dB with Over Power Protection

Thiele & Small Parameters|

• Equivalent Volume (Vas): 8.5 L
• Excursion (one way) (Xmax): 3 mm
• Free Air Resonance (Fs): 75 Hz
• Total Factor (Qts): 0.783

Speaker Measurements|

• Overall Diameter: 6.93″ / 176.1mm
• Overall Depth: 11.42″ / 290.2mm
• Overall Height: 10.7″ / 271.7mm
• 2.40″ / 60.9mm
• 4.13″ / 104.9mm
• 10.7″ / 271.7mm
• 3.51″ / 89.2mm
• 11.42″ / 290.2mm

Product Usage Instructions

Installation

1. Choose a suitable location for mounting the CF-X6TPneo Wakeboard Pod Tower Speaker.
2. Ensure that the mounting surface is stable and secure.
3. Attach the speaker to the mounting surface using appropriate screws or clamps.
4. Make sure the speaker is firmly attached and stable.

Wiring and Connections

1. Connect the positive (+) terminal of the speaker to the positive (+) terminal of your audio source.
2. Connect the negative (-) terminal of the speaker to the negative (-) terminal of your audio source.
3. Ensure that all connections are secure and properly insulated.

Powering On and Adjustments

1. Ensure that the audio source is turned off.
2. Connect the power supply to the CF-X6TPneo Wakeboard Pod Tower Speaker.
3. Turn on the audio source and adjust the volume to a suitable level.
4. Use the RGB LED controls, if available, to adjust the lighting settings according to your preference.

Maintenance and Care

• Regularly clean the speaker using a soft cloth and mild detergent. Avoid using abrasive cleaners.
• Inspect the speaker for any signs of damage or wear. Replace any damaged parts immediately.
• Store the speaker in a dry and safe place when not in use.

Specifications

General Specifications

Nominal Diameter……………… 6.5′
Nominal Impedance… ……………….. 4 ohms
RMS Power Handling.. .. 150 Watts
MAX Power Handling… ……….. 450 Watts
Sensitivity (1w/1m). …………… 93 dB
Frequency Response …. 70 Hz – 21 KHz
Recommended HI Pass Crossover.. 90 Hz

Body / Features
Enclosure Material……………………… Injection PC+ABS
Marine Grade Type……………………….. IP65 + UV Stable
GB LED…………………….. Integrated LED-RGB Speaker Lighting
Integrated LED-RGB Acrylic Ring Lighting
and LED-RGB Back Logo with 6 Core Wires
for Lighting and Speaker
Grill Type…………………………………… ABS+316 Stainless Metal Mesh
Clamps……………………………… Die-Cast adjustable (1″ 2″)
360 Degree Rotation Mounting
Buried Wire or Open Wire Mounting Optional,
Included NBR Pad And Stainless Hardware
(Screws, Stop Washers, Hexagon wrench,
Safety Rope, Screw fastening Glue)
Front Logo……………………………… Can be Rotated For Correct Angle Display
Rear Logo………………………………. Radiator Fixed Position
Finish………………………………… Gloss Black Carbon Fiber Texture

Woofer Specifications
Voice Coil Diameter…….. 1.5″
Cone Material………………. Waterproof Compress Paper+Carbon Fiber
Surround Material……. Soft PC Damping Glued
Basket Material…. PC Injection Molded Composite
Magnet Material…. Neodymium
Magnet Grade.N40H
Passive Radiator…. 3.5″ With LED GB Light

Tweeter Specifications
Voice Coil Diameter…………………… 1″‘
Type…………………………….. Compression Driver with NC Solid Aluminum Horn
Diaphragm Material……………………. PEN
Magnet Material…………………….. Neodymium
Crossover…………………………………. 12dB with Over Power Protection

Thiele & Small Parameters
Equivilant VolumeVas…….. 8.5 L
Excursion (one way)Xmax….. 3 mm
Free Air ResonanceFs… … 75 Hz
Total FactorQts……0.783

Speaker Measurements
Overall Diameter………………………….6.93″ / 176.1 mm
Overall Depth………………………………11.42″ / 290.2mm
Overall Height……………………………….0.7″ /271.7mm

DIMENSIONS

We Reserve The Right To Change Products And Specifications At Any Time Without Notice. Images May Or May Not Include Optional Equipment

READ BEFORE INSTALLATION

1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
3. For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink,etc.
4. Use high quality “Waterproof” connectors for a reliable installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. If installing in a boat, a make sure not cut or drill through the main hull.
6. Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
8. Make sure that the mounting clamp or “L” bracket are tight before leaving the dock.
9. Decide early what type of LED lighting you want (if any) and wire accordingly

( NOTE : if you want “Dancing Light” look to the WiFi or RF or BT remote controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

• An Electric Drill With Bits
• Vom (Electronic Volt Ohm Meter)
• Allen / Hex Key / Wrench Set
• Philips Head And Standard Screw Drivers
• Heat Shrink Tubing And Heat Gun
• Soldering Iron
• Wire Strippers
• Electronic (Rosen Not Acid Core) solder
• Crimping Tool

PACKAGING INCLUDES

• 1 Pair 6.5″ Wakebord Pod Tower Speaker
• 1 Piece 6 mm Hex wrench Chromed
• 1 Piece 4 mm Hex wrench Chromed
• 1 Pair NBR Pad For 1″ to 3″ tube adjust
• 1 Pair Stainless Safety Rope
• 1 Pcs Screw Fastening Glue

NOTE: The stainless steel hardware supplied with your speakers has been chosen to resist rust and corrosion. If the particular hardware supplied will not work for your installation purposes, please be sure to use only appropriate marine grade (stainless steel) mounting hardware.

INSTALLATION & CONNECTION OPTIONS

1. If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

INSTALLATION

BEGINNING MOUNTING
Step 1: Remove tower speakers from the packaging and ALL hardware.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights) – PLUS does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that hold the top clamp
Step 4: Drill o15 – 020 mm hole on mounting tube bottom align the clamp wire out hole.
Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.

Step 7: Wrap the rubber pad around the pipe and align wire out hole According to the diagram.

Step 8: Push the wire into the tube, press on the rubber pad,and lock the the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.
Step 10: If need be „rotate the speakers for best dispersion, this easily done by locating the 6mm&4mm hex wrench set screw on the side of the clamp base,rotate the speaker / enclosure to the desired angel, once there … locking the screws tight , Avoid vibration clamp loose!!!

Step 11: During the mounting process you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT(see Tie-wrap solution below) Step 12: Remove Wire NBR Plug and Slide the wire threw the hole Snake the wire down to the bottom of the tower tube in a location that the wires can be attached to the audio (And lighting) system. Solder or butt connect the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water/moisture.

Step 13: When vou want to install by flat mounting, remove the clamp and take out the 6 core through it into flat mounting bracket, then assemble it, see depiction below.

FLAT MOUNTING

TUBE MOUNTING

FOR MORE INFORMATION PLEASE VISIT

• DS18.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>