DS18 SLG-FKP6 Polaris Slingshot Front Kick Panel Pods for 6.5 Inch Speakers Owner’s Manual

SLG-FKP6 Polaris Slingshot Front Kick Panel Pods for 6.5 Inch Speakers
Owner’s Manual

SLG-FKP6
POLARIS SLINGSHOT FRONT KICK PANEL PODS FOR
6.5″ SPEAKERS & 3.8″ BULLET TWEETER

SLG-FKP6 Polaris Slingshot Front Kick Panel Pods for 6.5 Inch Speakers

POLARIS SLINGSHOT FRONT KICK PANEL PODS FOR 6.5″ SPEAKERS & 3.8″ BULLET TWEETERS

INTRODUCTION

If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding this durable Polyethylene Front Kick Panel Enclosure by DS18. This enclosure allows you to mount one 6.5″ Speaker and one bullet tweeter that your  stereo system deserves. This enclosure comes in pairs (Driver & Passenger) with a black textured finish to match the factory’s look. Very easy to Install using supplied bolts and brackets that fits directly into place.

FEATURES

• Pods Sold as a Set (Driver and Passenger).
• Easy to Install – All Hardware and Wiring Included.
• OFC tinned Wiring for more Power Handling and Durability.
• 6 core 0.6M Input Wires for RGB Lighting and Speakers.
• Fits Slingshot Models from 2015 or later
• Coated Metal Bracket for better Resistance to the Elements.
• Fits any 6.5” DS18 Speakers. (not included)
• Fits any 3.8” Bullet Tweeter. (not included)
• Durable (PE) Waterproof Enclosure with UV Protection.
• Sealed Type Waterproof Enclosure.
• Damping Material for Better Speaker Performance
• Black OEM Finish

SPEAKERS PARAMETERS

• Speaker Mounting Hole: 5.7” / 145mm.
• Speaker Mounting Depth: Up to 4.3” / 110mm.
• Tweeter Mounting Hole: 2.9” / 74mm.
• Tweeter Mounting Depth: Up to 2.5” / 66mm.

WHAT’S IN THE BOX

• Left & Right Speaker Enclosure
• Mounting Brackets
• Screws and washers
• Speaker Wiring

INSTALLATION

1. Remove the factory speaker enclosures using a T40 TORX socket to extract the (3) screws securing each speaker enclosure. Disconnect the factory connector and remove the speaker enclosure. If your vehicle did not come with a  factory speaker you will need to remove (1) T40 TORX screw on both driver and passenger side of the vehicle. The screw secures the vehicle factory plastic side panel to a bracket welded to the chassis tube. (Picture 1)
2. Start by assembling D, DD, and DDD brackets to driver’s side kick pod using (2) M6 Washer and (2) M6 Screw per bracket. Bracket DD will need to remain loosely hand tightened during this step. Fully tighten bracket D and DDD.  Repeat for passenger side kick pod. (Picture 2)
3. Installing the passenger kick pod will require the temporary removal of the factory glovebox. Open the glovebox door and release the tabs that are located at the back of the compartment. Lift and remove the glovebox. (Picture 3)
4. Place the Passenger kick pod into the vehicle pushing it as far forward as possible. This will allow you to angle in the rear of the kick pod so that bracket “P” is able to rest in between the factory metal bracket and plastic side panel. (Picture 4)
5. Once the bracket is resting between both surfaces tilt the front of the kick pod into position. 5. Next tighten the brackets to the vehicle using (3) M6 Thread Rolling Screws and (3) M6 washers. (Picture 5)
6. Re-Install Glovebox.
7. Before installing the driver’s side kick pod, start by tilting the steering wheel to its highest position.
8.  Repeat steps 1-5 to install the driver’s side kick speaker pod.
9. Install the speakers using the speaker wires included, use the same line to connect the tweeter and make sure to use a bass blocker filter to it, if you are using RGB led speakers connect the LED to the supplied wiring harness.
10. Secure the speakers using stainless steel screws and tighten it, be careful not to over-tighten or the hole may be damaged and not properly secure the speakers.
11. This kit can use the factory amplifier or an aftermarket amp pre-installed with the speaker wires in this location, only after this step can you install the speakers using the aftermarket amp’s speaker wire and RGB LED wires (optional) of the LED module (LED -BTC not included).
    This concludes the installation of the SLG-FKP6 and it is ready to enjoy your new sound system upgrade!

CONNECTION OPTIONS

1. If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:  Blue LED (-)
    Black 12V DC (+)
    Red LED (-)
    White Speaker (+)
    Green LED (-)
    Grey Speaker (-)

2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
   • Black wire”BK” connected to battery Positive (+) 12V
   • White Color Light “R”; “B” and “G” connected to battery Negative (-)
   • Green Color Light “G” connected to battery Negative (-)
   • Red Color Light “R” connected to battery Negative (-)
   • Blue Color Light “B” connected to battery Negative (-)
   • Purple Color Light “R” and “B” connected to battery Negative (-)
   • Yellow Color Light”R” and “G” connected to battery Negative (-)
   • Cyan Color Light “B” and “G” connected to battery Negative (-)

MEASUREMENTS

DRIVER SIDE

DRIVER SIDE

PASSENGER Side

PASSENGER Side

WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without notice.
Images may or may not include optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov

FOR MORE INFORMATION
PLEASE VISIT
DS18.COM

References

• Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>