DS18 SLG-WFCC8LD Polaris Slingshot Waterfall Center Console Speaker Pod Owner’s Manual
- June 13, 2024
- DS18
Table of Contents
HYDRO
SLG-WFCC8LD Polaris Slingshot Waterfall Center Console Speaker Pod
Owner’s Manual
OWNER’S MANUAL
SLG-WFCC8LD
POLARIS SLINGSHOT WATERFALL CENTER CONSOLE
SPEAKER POD WITH NXL-8BK & PRO-TW1L INCLUDED
SLG-WFCC8LD Polaris Slingshot Waterfall Center Console Speaker Pod
SLG-WFCC8LD
POLARIS SLINGSHOT WATERFALL CENTER CONSOLE SPEAKER POD WITH NXL-8BK & PRO-TW1L
INCLUDED
INTRODUCTION
If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding this durable Polyethylene Waterfall Center Console pod by DS18. This pod includes one 8″ Waterproof Speaker with RGB LED lights (NXL- 8BK) and one 3.8” Super bullet tweeter with RGB LED lights (PRO-TW1L) that your stereo system deserves. This pod comes with a black textured finish to match the factory’s look. Very easy to Install using supplied bolts that fits directly into place.
FEATURES
- Easy to Install – All Hardware and Wiring Included.
- OFC Tinned Wiring for More Power Handling and Durability.
- 6 core 0.6M Input Wires for RGB Lighting and Speakers.
- Fits only on 2015-2019 Slingshot
- Includes an 8” NXL-8BK Waterproof Speaker with RGB LED Lights.
- Includes a 3.8” PRO-TW1L Super Bullet Tweeter with RGB LED Lights.
- Durable (PE) Waterproof Panel with UV Protection.
- Black OEM Finish
WHAT’S IN THE BOX
- One Pod with NXL-8BK and PRO-TW1L included.
- Speaker Wiring.
- Screws and washers.
INSTALLATION
Remove the factory 12V port pushing down the clips and disconnect it, also
remove the cup holder to gain more room and seat properly. (Picture 1)
Place the pod in place and mark the holes to open at the sides, use a drill with a 1/8” bit and open the holes for the screws. (Picture 2)
Then secure the pod (Picture 4) and reconnect the 12V port in the new hole
position and re-connect it. (Picture 3)
This kit needs an aftermarket amp pre-installed with the speaker wires in this
location, only after this step can you install the speakers using the
aftermarket amp’s speaker wire and RGB LED wires (optional) of the LED module
(LED – BTC not included). (Picture 6)
This concludes the installation of the SLG-WFCC8LD and it is ready to enjoy
your new sound system upgrade!
CONNECTION OPTIONS
- If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
Blue LED (-)
Black 12V DC (+)
Red LED (-)
White Speaker (+)
Green LED (-)
Grey Speaker (-)
CONNECTION OPTIONS
- To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
• Black wire”BK” connected to battery Positive (+) 12V
• White Color Light “R”; “B” and “G” connected to battery Negative (-)
• Green Color Light “G” connected to battery Negative (-)
• Red Color Light “R” connected to battery Negative (-)
• Blue Color Light “B” connected to battery Negative (-)
• Purple Color Light “R” and “B” connected to battery Negative (-)
• Yellow Color Lighters” and “G” connected to battery Negative (-)
• Cyan Color Light “B” and “G” connected to battery Negative (-)
GENERAL :
Total Impedance……………………………………………………………………. 4 Ohms
Load Configuration …………………………………………………………………Parallel
Input Wire …………………………………………………………………………………6 Core OFC Tinned (2ft / 0.6m)
SPEAKER SPECIFICATIONS :
Speaker Type ………………………………………………………………… 8″ Waterproof Coaxial with RGB LED
RMS Power Handling ………………………………………………………………….125W
MAX Power Handling ………………………………………………………………..375W
Sensitivity (1w/1m) …………………………………………………………………………. 93dB
Frequency Response …………………………………………………………….. 35Hz-23KHz
Recommended Hi Pass Crossover ………………………………………. 50 Hz
Voice Coil Diameter ……………………………………………………. 1.2″ / 30.5mm
Voice Coil Former Material ………………………………………………..Kapton
Winding Material ………………………………………………………………….. CCAW
Cone Material …………………………………………………………… Injection Molded Polypropylene + UV
Compliant
Surround Material ………………………………….. Butyl (Rubber)
Basket Material ……………………… ………………..High Temp Injection Molded Composite with UV
Protection coating
Magnet Material …………………………………… Ferrite Neodymium
Magnet Weight ………………………………………………………. 14oz + 0.32oz
TWEETER SPECIFICATIONS
Speaker Type……………………………………………………………………..3.8″ Super Bullet with RGB LED
RMS Power Handling …………………………………………………………………………. 60W
MAX Power Handling ………………………………………………………………………..120W
Sensitivity (1w/1m) ……………………………………………………………………………….. 103dB
Frequency Response …………………………………………………………. 3.5KHz-20KHz
Recommended Hi Pass Crossover ………………………………………. 4KHz
Voice Coil Diameter …………………………………………………………1” / 25.4mm
Voice Coil Former Material ………………………………………………..Kapton
Winding Material …………………………………………………………………………………… CCA
Diaphragm Material ………………………………………………………Aluminum
Magnet Material ……………………………………………………………..Ferrite Y30
Magnet Weight ……………………………………………………………………………………………………. 8 Oz
BOX SPECIFICATIONS :
Box Type ………………………………………………………………….Front Baffle
Box Material ………………………………………………… Polyethylene (PE)
Finish Material ……………………………………………………………………………….Black
UV Protection …………………………………………………………………………………………………….. Yes
Waterproof Rating ……………………………………………………………………………… IP65
MEASUREMENT:
Overall Height ………………………………………………………………………………………… 17.4″ / 442.2mm
Overall Width ………………………………………………………………………………………… 9.12″ / 231.6mm
Overall Depth ……………………………………………………………………………… 9.44″ / 239.8mm
MEASUREMENTS
WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without
notice.
Images may or may not included optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov
SLG-WFCC8LD
FOR MORE INFORMATION
PLEASE VISIT
DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>