RYOBI RLL25GN 25m 360 Degree Green Line Laser Instruction Manual

RYOBI RLL25GN 25m 360 Degree Green Line Laser

IMPORTANT!
It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product.
Subject to technical modifications.

Safety, performance, and dependability have been given top priority in the design of your 360° line laser.

INTENDED USE

The 360° line laser is intended to be used only by adults who have read and understood  the instructions and warnings in this manual, and can be considered responsible for their actions.
The product is intended for determining and verifying horizontal and vertical lines.
The product is intended for indoor use only.
Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

CROSS LINE LASER SAFETY WARNINGS

• Laser radiation. Do not stare into beam. Class 2 laser product.

• Risk of severe eye injury if the laser beam is directed at persons or animals. Avoid direct eye exposure.

• Do not direct the laser beam towards other people.

• Do not operate the product around children or allow children to operate the laser.

• Avoid using the product on reflective surfaces. The laser beam may be reflected at the operator or other persons.

• When the product is brought into a warm environment from a cold one, or vice versa, allow it to come to the surrounding temperature before use.

• Store the product indoors and avoid substantial knocks, continuous vibration or extreme temperatures.

• Always keep the product from dust, liquids and high humidity. They may damage internal components or affect accuracy.

• If laser beam hits your eye, you must close your eyes and immediately turn your head away from the beam.

• Do not position the laser beam so that it unintentionally blinds you or others.

• Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope. This will increase the level of eye injury.

• If you use laser goggles to enhance the visibility of the laser beam, note that they will not protect your eyes against laser radiation.

• Do not remove or deface warning labels on the product.

• Do not disassemble the product.

• Avoid heavy impact to or dropping of the laser.
  The accuracy of the laser should be checked before use if it has been dropped or subjected to other mechanical stresses.

• Do not operate the product in explosive areas or in extreme environments.

• When not in use, make sure to turn off the power, and place the laser in its carrying pouch. Make sure the on/off switch is in the off position before transporting the laser.
  NOTE: If the on/off switch is not in the off position before transportation, internal mechanical damage may occur.

• If the product is not in use for a long period of time, remove the batteries from the battery compartment.
  This will prevent batteries from leaking and corrosion.

SELF-LEVELLING LED INDICATOR

a horizontal position of +/-4°.

MAINTENANCE

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• For greater safety and reliability, all repairs should be performed by an authorised service centre.

SYMBOLS ON THE PRODUCT

V

| Volts
---|---
| Direct current
| Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements.
| Read the instructions carefully before using the product.
| Class 2 laser beam. Do not stare into the laser beam.
| Note
| Do not stare into the laser beam.

Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators, and light sources have to be removed from the equipment. Check with your local authority or retailer for recycling advice and collection point. According to local regulations, retailers may have an obligation to take back waste batteries and waste electrical and electronic equipment free of charge. Your contribution to the reuse and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials. Waste batteries, in particular containing lithium, and waste electrical and electronic equipment contain valuable and recyclable materials,  which can adversely impact the environment and the human health if not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.

Product Overview

Installation

PRODUCT SPECIFICATIONS

25M 360 Green Line Laser

Model| RLL25GN
Accuracy| ±0.5 mm/m
Laser wavelength| 520nm ± 10nm
Colour| Green
Working range| 25 m
Laser class| 2, <1mW
Beam divergence| 1.5 mrad
Projection| Plane and vertical line
Self-leveling time| 2s ~ 4s
Self-leveling angle| ± 4°
Operating time| 5 h
Battery technology| 4 x AA LR6 Alkaline
Supply voltage| 4 x 1.5V
Operating temperature range| 0°C ~ 40°C
Storage temperature range| -20°C ~ 70°C
Dimensions| L86 x W70 x H110 mm

Customer Service

Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20230303v1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>