RYOBI R18BT150C4P 18V ONE Plus 150W Inverter with 21W Solar Panel 4.0Ah Kit Instruction Manual

**RYOBI R18BT150C4P 18V ONE Plus 150W Inverter with 21W Solar Panel 4.0Ah Kit Instruction Manual

**

IMPORTANT!
The product is not intended to be used or cleaned by persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge unless they have been given instructions concerning the safe use of the product by a person legally responsible for their safety. They should be supervised while using the product. Children shall not use, clean or play with the product, which when not in use should be secured out of their reach.
Subject to technical modification.

Safety, performance, and dependability have been given top priority in the design of your battery inverter and solar panel.

INTENDED USE

The battery inverter may be used for the following purposes:

• operating and charging USB-powered devices
• supplying electrical power for operating compatible small electronics such as cell phones, tablets, laptops, LED lights, fans, radios, etc.
• charging RYOBI 18V ONE+ battery packs

The battery inverter is intended for indoor use only. When a battery pack is installed, the battery inverter converts DC electricity to the charging power outputs listed in this manual, allowing the user to charge and power a variety of devices.
The battery inverter’s AC receptacle has a non-sinusoidal (modified sine wave) output and is not recommended for use with certain types of sensitive electronics or electrical devices containing a compressor. Refer to the electronics’ operator’s manual.
The battery inverter is rated at 150 VA continuous power output and 450 VA startup power output. Check the power rating of your electrical device before using with the battery inverter. The power output can exceed 150 VA on startup if the maximum output is 450 W.
The battery inverter can recharge a battery pack when connected to a household power supply or connected to the solar panel. If a battery pack is being charged, the battery inverter does not provide power to any device connected to the USB-A charging ports.
The solar panel charges or powers USB devices using converted solar energy. The solar panel can provide power through USB-A and USB-C outputs. The solar panel is intended for outdoor use with good light exposure. The product is designed for home or domestic use. Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

Save all warnings and instruction for future reference.

• Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone the product, loan them these instructions also.
• Do not recharge primary cells (non-rechargeable).
• Do not expose the product to rain, wet, or damp conditions. Water entering the product increases the risk of electric shock.
• Do not use the product if it has been dropped or received a sharp blow. A damaged product increases the risk of fire. Always inspect the product for damages before use.
• The product should be operated only with the battery packs specified in this manual. When using batteryoperated products, follow basic safety precautions to reduce the risk of fire, leaking batteries, and personal injury.
• Do not disassemble or modify the product. Electric shock hazard may occur even when a battery is not installed. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
• Use caution when plugging or unplugging other devices into the product. Do not force plugs into the product.
• Do not put foreign objects into the product.

BATTERY INVERTER SAFETY WARNINGS

• Remove the battery pack from the product when not in use.
• To reduce the risk of injury, close supervision is necessary when the product is used near children.
• Store the product indoors and away from children.
• If the product is used in a manner not specified by the manufacturer, the protection provided by this equipment may be impaired.
• Do not overload the product. The product must be used for powering devices less than the product rating.
• Never block the air vents. Blocked vents may cause overheating. The product automatically turns off when overheated.
• Keep the product cool. Do not place the product near heat vents or in direct sunlight.
• Do not use the product around flammable fumes and gases, such as in the bilge of a boat or near propane tanks.
• Operate the product using only the AC power type listed in the product specifications.
• The product should never be hard-wired into a circuit.
• Do not leave the product unattended during operation.
• Operate the product only in temperatures between -15 °C and 40 °C.
• Do not use the product to power life support devices or other medical equipment.
• This is an isolated inverter and has double insulated construction. It does not utilise earth connection for protection. Do not power devices which are damaged or with damaged or frayed power cords.
• An internal cooling fan runs to regulate the product’s operating temperature. Always wait for the fan to stop before disconnecting the battery pack from the product.
• Use RYOBI 18V ObNE+ battery packs only. Do not use battery packs from other manufacturers.
• The light source of the product is not replaceable. When the light source reaches its end of life, the product must be replaced.
• Store the product in a location where the ambient temperature is between 15 °C and 60 °C.

SOLAR PANEL SAFETY WARNINGS

• Use the product in areas with good light exposure. Avoid using the product under trees, awnings, overhangs, and behind windows that are screened, tinted, or with dividers or obstructed views.
• Use the product flat on the ground, on a level surface, or hung on a vertical surface.
• Position the product so the angle of the panels are perpedicular to the sun for best performance. Cloud cover and dirty panels results in less exposure, decreasing the charging capacity of the solar panel.
• When hanging the product vertically, make sure to fasten it securely. Damage can occur if the product falls.
• Use caution when touching the product. The product may generate heat during use.
• Disconnect the devices after charging and fold the solar panel before storing.
• Use only the solar panel provided with the product.
• Store the product indoors.
• If the product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired.

MAINTENANCE

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, and grease.
• Do not, at any time, let brake fluids, gasoline, petroleum based products, and penetrating oils come in    contact with plastic parts. These products contain chemicals that can damage, weaken, or destroy plastic.

SYMBOLS ON THE PRODUCT

Safety alert

Electrical shock hazard

Remove the battery pack before starting any work on the product.

Do not expose the product to rain or damp conditions.

Press the power button for 2 seconds to turn the product on or off.

Isolated inverter

Class II: Protection against electric shock rely on double insulation or reinforced insulation.

Regulatory Compliance Mark (RCM). The product meets applicable regulatory requirements.

Indoor use only

Fast blow fuse

Read and understand all instructions before operating the product. Follow all warnings and safety instructions.

Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

Parts or accessories sold separately

Note

Warning

Connect to power outlet

Disconnect from power outlet

OPERATING THE BATTERY INVERTER

Avoid unwanted circuit breaks by identifying the starting and running watts of the devices to be connected. To calculate the starting wattage values, follow the following steps:

• Add the running watts of all the devices to be connected to the battery inverter. The devices should be under 150 W (150 VA).
• Add the largest starting watts of the devices to be connected.

The sum of the added watts are the maximum starting watts and must be within the limitations of the battery inverter AC output.
NOTE: When there are other devices connected to the battery inverter, some devices might experience wattage surge. Check the manuals of the connected devices to confirm.

PRODUCT SPECIFICATIONS

Battery inverter

Model| R18BT150C
Battery pack| RB1840C
Charger| –
Supply| 18 V d.c.16 A max
AC output| 230 V 50 Hz, 150 VA
USB-A output| 5 V d.c / 3 A9 V d.c / 2 A12 V d.c / 1.5 A
USB-C output| 5 V d.c. / 3 A9 V d.c. / 3 A12 V d.c. / 2.5 A20 V d.c. / 1.5 A
Dimensions| 137 x 90 x 74 mm
Weight| 370 g
Compatible battery packs| RB18L15, RB18L15A, RB18L15B, RB18L20, RB18L20A, RB18L25, RB18L25A, RB18L40, RB18L40A, RB18L50, RB18L50A, RB18L13, RB18L60A, RB18L90A, RB1815C, RB1820C, RB1825C, RB1840C, RB1840X, RB1850C, RB1850X, RB1860X
Solar panel|
Model| RSP21
Rated power| 21 W
USB-A output| 5 V d.c.
USB-A to USB-C cable output| 30 W
Dimensions| 170 x 310 x 20 mm
Weight| 540 g
Consumer product category:
Category 1: mobile applications
Category 2: portable applications
Category 3: attached applications

LED INDICATOR DESCRIPTIONS

POWER BUTTON LIGHT

Red LED| Green LED| Yellow LED| Status| Troubleshooting
---|---|---|---|---
–| On| –| The product is on.| –
On| –| –| The product is overloaded.|

1. Press the power button to remove the lock state. The LED indicator turns off.
2. Disconnect all devices. Make sure that the battery pack is sufficiently charged.
3. Press the power button to turn on the AC socket.
4. Reconnect all devices. If the LED indicator flashes red again, the devices exceed the capacity of the battery inverter.

On(flashing)| –| –| The product is overheated.|

1. Disconnect all devices. Allow the battery inverter to cool down until the LED indicator flashes red.
2. Briefly press the power button to reset the battery inverter. When the LED indicator turns green, reconnect the devices.

–| –| On(flashing)| The battery pack charge is low.| Remove and charge the battery pack.
Red LED| Green LED| Yellow LED| Status| Troubleshooting
On (solid, then flashing)| –| –| The product is connected to a power supply.|
–| On (flashing)| –| The battery pack is being charged.|
–| On| | The battery pack is fully charged.|
–| –| On (flashing)| The power delivery is insufficient.| Disconnect the battery inverter from the power supply and reconnect. If the solar panel is connected, position the solar panel so that the angle of the solar panel is perpendicular to direct sunlight.
On(flashing)| –| –| There is a power delivery input or high temperature issue.| If the red LED light continues flashing, remove the power input or battery pack to allow the battery inverter to cool down. Check the connections of the battery inverter or solar panel.
On| –| –| There is a battery pack or charging input issue.| If the red LED light continues to turn on, remove the power input or battery pack to allow the battery inverter to cool down. Check the connections of the battery inverter or solar panel.
On(flashing)| On (flashing)| –| The battery pack is not charging properly or is not compatible.| Remove and test the battery pack.

BATTERY INVERTER RUNTIME GUIDE

Battery pack| Device type| Maximum runtime (under optimal conditions)
---|---|---
4.0 Ah| 6-inch smartphone| 4 charges
8-inch tablet| 3 charges
15-inch laptop| 1 charge
32-inch LED TV| 60 mins
Internet modem| 10 hrs

Instruction

Insert the battery pack into the battery port. Make sure that the latches on the battery pack click into place.

Press the power button for 2 seconds to turn on the battery inverter. The area/ warning light button turns on. Press the power button again for 2 seconds to turn off the battery inverter.

Connect a USB-C device into the USB-C port. Press the power button for 2 seconds to turn on the battery inverter and charge the connected device

Connect a USB-A device into the USB-A port. Press the power button for 2 seconds to turn on the battery inverter and charge the connected device

Using a USB-C to USB-A cable, insert the USB-C connector into the USB-C port and insert the USB-A connector to the adaptor. Connect the adaptor to a power supply.

Using a USB-C to USB-A cable, insert the USB-C connector into the USB-C port and insert the USB-A connector to the 12 V adaptor. Connect the 12 V adaptor to a 12 V socket.

Connect a 240 V AC device (150 W max) to the AC socket.

Connect a USB-A device into the USB-A port.

Press the power button for 2 seconds to turn on the battery inverter. Press the area/warning light button once to set the brightness of the area/warning light to 30%. Press the button twice to set the brightness to 60%. Press the button three times to set the brightness to 100%. Press the button 4 times to turn off the area/warning light.

Open the top, middle, and bottom flaps until the solar panel is completely unfolded.

Using the zipper, open the pocket on the top flap.
NOTE: The USB-A ports are inside the pocket.

Connect a device to the USB-A port to charge the device.

Using a USB-C to USB-A cable, insert the USB-A connector into the USB-A port of the solar panel. Insert the USB-C connector to the USB-C charging port of the battery inverter. The USB-A port automatically detects the power delivery and turns off the battery inverter if it is on. When initially connected to a power supply, the charge light of the battery inverter turns solid red, then flashes. The charge light flashes green if the battery inv

NOTE: Weather conditions may decrease the efficiency of the solar panel. At peak wattage output at 25 degrees, the solar panel can deliver 72 Wh (maximum storage energy) to the RB1840C battery pack in 6 hours.

Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia

Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand

RYOBI is a trade mark of Ryobi Limited, and is used under license.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>