Mr Beam Lasercutter 43420683326 Desktop Lasercutter

Product Information

The product is called “Mr Beam” and it is a laser cutting and engraving machine. It comes with an Air Filter System that helps filter the air during the operation. The product has various components including the laser head, power cable, network cable, and screws.

Product Usage Instructions

1. Unpack and set up Mr Beam by connecting the LAN cable and power cable.
2. If the product comes with the Air Filter System, connect it to Mr Beam using the provided screws and washers.
3. If the product does not come with the Air Filter System, skip this step.
4. Connect the laser head to Mr Beam. Make sure to disconnect Mr Beam from the power source before connecting or disconnecting the laser head.
5. If using the Air Filter System, connect it to Mr Beam using the provided hose. Make sure to screw the exhaust nozzle onto the end of the hose (left-hand thread).
6. If not using the Air Filter System, make sure to provide proper ventilation for the exhaust air.
7. To power on/off Mr Beam, use the corresponding buttons on the device.
8. Connect your computer to Mr Beam either via Wi-Fi or by connecting it with a network cable.
9. Follow the instructions in the user manual to establish a connection between your computer and Mr Beam.
10. For Wi-Fi connection, connect your computer directly to Mr Beam’s Wi-Fi network using the provided credentials.
11. For network cable connection, connect Mr Beam to your router using the provided network cable. Make sure your computer is also connected to the router either via cable or Wi-Fi.
12. Follow the instructions in the user manual to complete the connection setup.
13. Once connected, you can use the Mr Beam Welcome Dialog to further configure and control the device.
14. To focus the laser, refer to the chapter on “Mr Beam Fokussierung” in the user manual. Follow the instructions to adjust the laser focus for different material thicknesses.

SAFETY INSTRUCTIONS

You can find the latest version of this Quick Start Guide, as well as that of previous modells, and some other information about your Mr Beam at the following QR Code.

At www.mr-beam.org/support, you will also find answers to many questions regarding Mr Beam.

User Manual
Before using your Mr Beam, please read and understand the user manual and the safety instructions.

You can find the latest manual and safety instructions in the menu of your Mr Beam user interface and on mr-beam.org/downloads.

Only process materials that Mr Beam Lasers has classified as harmless. You can find an up-to-date list of materials at mr-beam.org/materialien

Warning: Never process PVC, vinyl, glass fiber, carbon fiber or materials containing chlorine!The processing of these materials produces toxic fumes that can damage your health and machinery. cause machine damage and health hazard.

UNPACKING AND SETTING UP YOUR MR BEAM

First, remove the small box on the side. The laser head, the power adapter, the key and the Focus Tool are inside it.

Remove the transport safeguard inside the device carefully.

SCOPE OF DELIVERY – WITH AIR FILTER SYSTEM

For indoor use we recommend a Mr Beam Air Filter System. If you don‘t have one yet, order it now from our shop at www.mr-beam.org

CONNECTING THE LASER HEAD TO THE X-AXIS

Attention: In order to connect and disconnect the laser head, the Mr Beam must be dis-connected from the power supply!

Remove the sticker from the back side of the laser head.
Mount the laser head to the base plate using the knurled screw.
Tighten the knurled screw moderately with two fingers.

Then connect both the hose, as well as the rib-bon cable to the laser head.
Attention: The silver contacts of the ribbon cable must be on the top.
The black bracket fixes the ribbon cable to the socket.

Attention: To disconnect the cable, pull out the bracket about 2 mm carefully. For fastening, press in the bracket on both sides.
To adjust the laser focus to different material heights, the base plate can be mounted at different heights. You can make fine adjust-ments using the knurled screw and the slotted hole in the base plate.
See the chapter: Mr Beam Focusing

CONNECTION OF THE SUCTION / AIR FILTER SYSTEM

Screw the elbow to the end of the hose (left-hand thread).

Screw the contra-angle incl. hose to the housing using the knurled screws. Place the washers between the screw and the rubber.

Also connect the Mr Beam Air Filter System or suction fan with the appropriate cable.

Connect the Mr Beam Air Filter System or suction fan to your Mr Beam.

Caution: If you operate your Mr Beam without Mr Beam Air Filter System, you are obliged to ensure that the waste air is discharged properly.

To do this, direct the waste air outdoors or connect the hose to an existing waste system. Fix the hose carefully and prevent the waste air from entering the room.

POWER SUPPLY / ON-OFF SWITCH

Connect the power adapter to your Mr Beam before you connect it to the socket.

Turn on your Mr Beam using the key. It serves as access control for authorized users.

Press the button to turn on your Mr Beam. The light of the laser head is switched on immediately and after 10 seconds the Status Lights are also switched on.

To shut down your Mr Beam, press the button 5 seconds until the Status Lights turn permanently red. After 15 seconds the whole system shuts down.

When all the lights in the Mr Beam are off, turn the key to turn it off completely.

STARTING UP

Connection options with Mr Beam
There are three options to connect Mr Beam to your computer or tablet. Choosing the most appropriate option depends on your personal usage preference and the network available at the location Mr Beam is set up in. In all cases you need the Google Chrome Browser. Other Browsers are not supported.
Please choose one of the following connection options and proceed with the installation in the section “Status Lights“ on the next page.

Option A: Connection via Wi-Fi
Connect your computer directly to the Wi-Fi of your Mr Beam. This is the easiest connection option. No internet access or network infrastructure is required. You may not be able to use the internet on your computer while you are connected to Mr Beam. See page 11.

Option B: Connection via network cable (Ethernet) and router
Connect Mr Beam to the network router using a cable. Then, use the find.mr- beam service to create a connection to your Mr Beam.
This option is particularly stable due to the cable connection. An internet connection is necessary for the use of the find.mr-beam service. See page 12.

Option C: Connection via Wi-Fi and router:
Connect your Mr Beam to your network via Wi-Fi. To do this, connect Mr Beam to your Wi-Fi using the Wi-Fi-name and password. For initial setup, you need to connect via Option A or B first. The initial setup may be a little complicated, but in the long term, this is the most comfortable option that many users prefer. See page 13.

CONNECTION WITH MR BEAM

Status Lights
Whether you are setting up for the first time or have connected to your Mr Beam many times before, the Mr Beam Status Lights will show you how to connect to your Mr Beam right now. For this purpose, the Status Lights pulsate (blink slowly) in different colors.

Green pulsation:

Your Mr Beam pulses green if a Wi-Fi direct connection is possible.
The direct connection via the Wi-Fi of the Mr Beam is used during the initial setup and if you want to operate the Mr Beam without an active internet connection. (e.g. at fairs or in the base-ment).
For more details of the Wi-Fi direct connection, please refer to page 30.

Orange pulsation:

Your Mr Beam pulses orange if it has an active internet connection.
In this case, you can access your Mr Beam via find. mr-beam.org in the Google Chrome browser.
More details about the active internet connection (via rou-ter or network cable) can be found on page 31 and 32.

White pulsation:

Your Mr Beam pulses white if it is connected to your local network but has no active internet connection. Visit our online Knowledge Base to find possible solu-tions.
When pulsing green and white at the same time, a Wi-Fi direct connection is possible and it is connected to your network router, but still cannot be found on find. mr-beam.org.

In all cases, you can find more information in our online knowledge base at www.mr-beam.org/docs/lights.

OPTION A: DIRECT CONNECTION VIA MR BEAM WI-FI

Note: During the initial setup, your Mr Beam will guide you through the Mr Beam Welcome Dialog. If you wish to do so, you can set up a Wi-Fi connection with the router there. Other-wise, this is also possible at a later time in the settings.

OPTION B: CABLE AND ROUTER

Connect your Mr Beam to your router with a network cable (Ethernet). The network socket is located on the back under the USB ports.
Note: Do not confuse the socket with the Air Filter System connection on the other side.

Make sure your computer is also connected to the router via cable or Wi-Fi.

After a few seconds (maximum 60 s), your Mr Beam will pulsate with orange lights. The next steps can be found on page 29.
Note: During the initial setup, your Mr Beam will guide you through the Mr Beam Welcome Dialog. If you wish to do so, you can set up a Wi-Fi connection with the router there.

OPTION C: WI-FI AND ROUTER

For initial setup, you need to first connect through either option A or B to get to the Welcome Dialog, where you can set up your Wi-Fi connection.
If you select Option A, connect your computer directly to the Wi-Fi of your Mr Beam. After-wards enter the IP address 10.250.250.1 in your Google Chrome browser. This process is descri-bed in detail on page 30.

If you have a cable, select Option B to connect Mr Beam to your router with the cable. Now use the find.mr-beam service to connect to your Mr Beam for the first time. This process is described in detail on page 31.

Independently of the chosen option, Mr Beam will greet you with the Welcome Dialog. During the Welcome Dialog, you have the option of connecting your Mr Beam to your Wi-Fi. Click the Connect button that appears next to your Wi-Fi network name and then enter your Wi-Fi password.
Note: A similar process is performed when registering a new smartphone in your Wi-Fi.

OPTION C: WI-FI AND ROUTER
If you have selected the Option A for initial setup and are connected to the Mr Beam via Wi-Fi, Mr Beam will interrupt the Wi-Fi connection to your computer to connect to your wireless router. If successful, your Mr Beam will soon pulsate with orange lights and you can connect to the find. mrbeam service.
Note: If this fails, e.g. because you entered an incorrect password, you will not receive an error message because you are no longer connected to your Mr Beam. In this case, you have to repeat the connection process of the Option A from the beginning.

If you have selected the Option B using a cable for initial setup, Mr Beam will tell you if the connection to your router was successful or not. If successful, you can now disconnect the network cable, use the Wi-Fi connection and use the find.mr-beam service.

If you notice a slow connection while operating your Mr Beam, e.g. If the pictures of the camera do not load or load slowly, this is probably due to a poor Wi-Fi connection. In this case, try option B (network cable and router).

MR BEAM FOCUSING
You need to focus the laserhead to achieve the best result with your Mr Beam.

Because the laser light conically leaves the laser head, there is one point at which it is focused maximally, the Focus point. At this point, your Mr Beam has the maxi-mum performance and highest precision. Therefore, the Focus point should be positioned exactly on the material and needs to be manually adjusted to the material height. For this adjustment, the distance between the bottom edge of the laser head and the top edge of the material has to be 10mm. Use the Mr Beam Focus Tool for this.

Rough focus

1. Attach the laser head to one of the four different positions

Fine focus

1. Open the screw on the left side of the laser head to move it up and down.
2. Place the focus tool with the cross between material and laser head

Position laser head

1. Place the laser head on the cross of the focus tool.
2. Then tighten the screw again moderately

Legend:

1. Laser: Go to laser job parameters proceed
2. Working area: If the lid of the Mr Beam is fully open, an image is taken every five seconds an image is taken and displayed on the working area. Double click on any position so that the laser head moves to the desired position.
3. Design library: Upload designs here and select uploaded designs.
4. Design store: Choose from a large selection of ready-made designs.
5. Support and settings

Creating SVG files
If you create a vector file for cutting and engraving, please observe the following details:

• filled areas will always be engraved
• lines can be cut or engraved
• choose different colors while creating the file to select different parameters in the Mr Beam Software later

MR BEAM MAINTENANCE AND CARE

Attention: Regular maintenance and care are necessary. Before cleaning and maintenance, always switch off the Mr Beam and disconnect the power plug.

Laser head
The laser head should be cleaned regularly. As a guide value the cleaning requirement can be viewed in the software under Settings -> Maintenance. If you work with materials which generate a lot of dust, such as wood, cleaning of the laser head may be necessary before 100% is reached.

Mechanics
The guide rails of the mechanical system must be regularly cleaned of dust and dirt.
We recommend using a mild, grease-dissolving cleaner and a damp cloth for this purpose.

Working Area
To protect the Mr Beam from unnecessary workload and possible ignition of small parts, always keep the interior clean.

MR BEAM AIR FILTER SYSTEM

To ensure that the exhaust air is cleaned by the Air Filter System, the filters must be changed regularly.
The voucher code QUICKSTARTGUIDE gives you a 10€ discount on your first filter order in our Mr Beam online shop. www.mr-beam.org

Before starting
Check the prefilter and main filter for correct seating. The prefilter must lie flat and cover the entire surface.
The soft, fluffy side of the prefilter must point upwards.

Filter change
The filters should be checked regularly. As a guide value, the wear of both filters can be viewed in the software under Settings -> Maintenance. If you work with materials which generate a lot of dust, such as wood, it is may be necessary to change the filters before they reach 100%.

EU Declaration of Conformity

• Company: Mr Beam Lasers GmbH
• Address: Gollierstrasse 70 80339 München
• Product category:  Laser cutting and engraving machine
• Model name: Mr Beam
• Manufacturer: Mr Beam Lasers GmbH
• Article number: MB DC-015, MB DCB-016, 900-#####, 901-#####, 902- * Serial number: 0000000012345678-2E (Beispiel)

The product fulfill the relevant European harmonization legislations:
Legislation:Title:
2014/53/EU Radio Equipment Directive (ABl. L 153, 22.5.2014, p. 62–106)
2006/42/EC Machinery Directive (ABl. L 157, 9.6.2006, p. 24–86)
2011/65/EU:2014-02-14 RoHS (ABl. L 174, 1.7.2011, p. 88–110)

The compliance with the requirements of the European harmonization legislations was proved by the application of the following harmonized standards and technical specifications:

Standards:  Description

• EN 60825-1:2022-08-01

• Safety of laser products – Part 1: Equipment classification and requirements

• EN 60825-4:2011-12 Safety of laser products – Part 4: Laser guards
  Safety of machinery – Laser processing machines – Part 1: Laser safety requirements

• EN ISO 11553-1:2020
  Safety of machinery – Laser processing machines – Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2)

• EN 12100:2011-03 (inkl. Berichtigung 1:2013-08)
  Safety of machinery – General principles for design – Risk assessment and risk reduction

• EN 61000-6-3:2022-07-01
  Lasers and laser-related equipment – Laser device – Minimum requirements for documentation
  Electromagnetic compatibility of multimedia equipment – Emission requirements
  Electromagnetic compatibility of multimedia equipment – Immunity requirements
  Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current <= 16 A per phase)
  Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection
  Electromagnetic compatibility (EMC) – Part 6-1: Generic standards – Immunity for residential, commercial and light-industrial environments Electromagnetic compatibility (EMC) – Part 6-3: Generic standards – Emission standard for residential, commercial and light-industrial environments Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz band; Harmonized Standard for access to radio spectrum 5 GHz RLAN; Harmonized Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
  ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
  DIN EN 301489-1
  Part 1: Common technical requirements; Harmonised Standard for ElectroMagnetic Compatibility
  EN IEC 63000:2018  63000:2016) EN IEC 63000:2018)

• EN 50689:2021
  ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
  Part 17: Specific conditions for Broadband Data Transmission Systems;
  Harmonised Standard for ElectroMagnetic Compatibility
  Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances (IEC 63000: 2016); German version

• EN IEC 63000:2018
  Safety of laser products. Particular Requirements for Consumer Laser Products

Additonal information:
München / 13.04.2023
Place / Date Sebastian Donner, Head of Engineering Roland Kaindl (TKRM UG haftungsbeschränkt), CE Consulting
This copy of the declaration of conformity is dated 04/13/2023. r You can also download the current versions of the operating instructions and declaration of conformity from: www.mr-beam.org/conformity

Happy & Excited
Tell your friends and family! Share your results with the Mr Beam community and the rest of the world.

madewithmrbeam

Questions & Problems
Check out our knowledge base: mr-beam.org/support Create a Support Ticket to contact our friendly customer service team: mr-beam.org/ticket

Get Inspired

 youtube.com/mrbeamlasers

instagram.com/mrbeamlasers

facebook.com/groups/officialmrbeamusers

© 2023 | Mr Beam Lasers GmbH | Gollierstraße 70 | Munich | Germany | www.mr- beam.org

References

• find.mr-beam.org - Easily connect to your Mr Beam laser cutter
• Mr Beam Lasers GmbH (@mrbeamlasers) • Instagram photos and videos
• Mr Beam Lasers ? Dein Lasercutter Experte | Jetzt entdecken
• Mr Beam Lasers ? Dein Lasercutter Experte | Jetzt entdecken
• Mr Beam Status Lights tell you how to connect : Mr Beam Lasers Support
• Downloads ? Mr Beam Lasers | Jetzt entdecken
• Kategorien – Mr Beam Lasers
• Support : Mr Beam Lasers Support
• Submit a ticket : Mr Beam Lasers Support
• Mr Beam Lasers ? Dein Lasercutter Experte | Jetzt entdecken
• Informationsportal ➡️ Mr Beam Lasers
• Mr Beam Status Lights tell you how to connect : Mr Beam Lasers Support
• Maintenance and hardware support : Mr Beam Lasers Support
• Das BeamOS® ? Lasercutter Software | Mr Beam Lasers
• Support : Mr Beam Lasers Support
• Wartung und Hardware Support : Mr Beam Lasers Support
• Betriebsanleitungen für den Mr Beam Lasercutter : Mr Beam Lasers Support
• Materialien und Parameter : Mr Beam Lasers Support
• #madewithmrbeam on Instagram | Hashtags

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>