GTSimulators com BPT195 Thyroid Biopsy Ultrasound Training User Guide

GTSimulators com BPT195 Thyroid Biopsy Ultrasound Training

Cautions and Warnings
Read this user guide, including all cautions and warnings, before you use your CAE Blue Phantom™ ultrasound training model. Use this product only as described in this guide. If you use the product incorrectly, it may be unsafe and will void your warranty. Keep this information for future reference.

General Precautions

• Make sure the training model is set up on a stable, sturdy work surface such as a bed, stretcher, or table that will not collapse and cause injury to users.
• Heavier training models should be placed on a patient bed or stretcher rated to support such weight.
• Place the model on smooth surfaces only. Rough or uneven surfaces can leave impressions on the skin and damage the model.
• Do only the procedures supported by each product as described in this guide.
• Use only needles for any procedures supported by this model.
• Do not use or store other sharp objects such as scissors, scalpels, or box-cutters with the training model.
• Do not pull on the training model skin. This can cause the skin to tear.
• Do not mark directly on the training model as this will permanently damage it.
• Do not insert any objects or tools into the model except for the equipment, accessories, or medical supplies intended for use with this model.
• Do not use chemical solvents on the models.
• Clean the training model with water and a light soap solution only. Do not immerse the model or use large amounts of liquid to wash it.

Latex-Free

• All CAE Blue Phantom training models, products, and accessories are manufactured only of materials that do not contain latex.

Needles and Catheters

• Use only new, sharp, unbent 18-21 gauge needles or 7F catheters. Smaller needles (higher than 22 gauge) can bend during use and damage the model.
• The self-healing feature of CAE Blue Phantom simulated tissue applies only to needle sticks from 18-21 gauge needles. Healing is not guaranteed if needles larger than 18 gauge, scalpels, or other sharp implements are used to cut into or pierce the model.
• Replace needles after ten uses. Dull needles can damage the model.
• Use extreme caution when using needles during training to avoid injury.

Service and Repair

• The CAE Blue Phantom training models are not user-serviceable. Only a trained technician may open or disassemble the product.
• Unauthorized use or handling of the model may void the warranty.
• If you have a problem with your product, contact CAE Customer Support.

Introduction

This user guide describes the features, use, and care of the following training model:

• CAE Blue Phantom Thyroid Biopsy Ultrasound Training Block (BPT195)
• This model is intended as a platform for the practice of ultrasound-guided thyroid biopsy.

Anatomy

CAE Blue Phantom training models are constructed using our patented Simulex™ ultrasound tissue which has imaging characteristics that mimic human tissue. The models contain skeletal components so the user will encounter the same imaging landmarks as in a human patient.
This model contains the following anatomy:

• Thyroid
• Focal lesions for fine-needle biopsy
• Left and right thyroid gland lobes
• Isthmus
• Multinodular goiter
• Multiple masses of varying sonographic appearances
• Trachea
• Esophagus
• Carotid arteries
• Internal jugular veins
• Multiple simple and complex masses

Equipment Overview

The following items are included with your shipment:

• Ultrasound training block
• Plastic storage case

The following additional items are required for training but not included in your purchase:

• Ultrasound system with appropriate transducer
• Ultrasound gel

CAE Blue Phantom training models are compatible with any diagnostic ultrasound system. General frequency ranges for diagnostic ultrasound imaging are 2-20MHz.

Using the Training Model

This section has information and instructions about the setup and use of the training model and any specific training procedures.
Setup
Follow the guidelines below to unpack and set up your CAE Blue Phantom training model.
Open the shipping carton:

• Use extreme caution with sharp tools, such as a box cutter, to avoid damage to the training model.

Unpack the equipment:

• Remove the training model from its shipping container. For heavier models, use proper lifting techniques to prevent bodily injury.
• Review the equipment, accessories, and supplies to make sure all necessary pieces are present. See the Equipment Overview section of this guide for a list of items included with this model.

Set up for training:

• Put the model on a stable patient bed, stretcher, or table.
• Prepare your ultrasound system and equipment.
• Gather any procedural equipment and supplies.

Training

This section provides information about using your model for training and practice.

Ultrasound Scanning

Note: CAE Blue Phantom products do not teach ultrasound procedures or techniques. Refer to your institution or training program for more information.
To scan with your training model and conduct a simulated ultrasound-guided procedure:

1. Place the model in the appropriate position for scanning.
2. Place ultrasound gel on the transducer or on the training model in an adequate quantity so that the transducer slides effortlessly on the model. Add more gel as needed.
3. Adjust the ultrasound system controls per your training protocol and the manufacturer’s instructions. Optimize the image with the ultrasound controls as needed.

Ultrasound-guided Procedures
Your CAE Blue Phantom training model is a realistic platform for complete thyroid biopsy procedural training. Use your normal protocol and equipment, and follow your institution’s policies and guidelines.
CAUTION: Do not use antiseptics, such as iodine, on the model. This can cause permanent damage. When a tissue sample is taken from the model, it leaves an air-filled space the same size as the sample. Once a tissue sample is removed, it cannot be re-inserted. Therefore, this product has a finite lifespan.

Care and Maintenance

With proper care, your training model will remain in optimal condition and ready for use.
Storage and Transport
Follow these guidelines to properly store or transport your model:

• Storage temperature degree range: 45 to 85 °F (7 to 29 °C)
• Store the model in its plastic storage case.
• Transport the model in its plastic storage case.

Cleaning

To maintain the product skin for the lifespan of the product, clean the exterior of the model after each use.
Follow these steps:

1. Mix one cup of tap water with ¼ teaspoon of mild liquid soap (such as dish soap).
2. Gently clean the model’s exterior with the soap mixture and a soft, non-abrasive sponge or cloth.
3. Rinse lightly with clean water.
4. Dab or pat with a clean, soft, lint-free cloth to dry the product after cleaning. Do not wipe or rub the skin, which can damage it.
5. After the model has dried completely, lightly coat the external surface of the model with baby powder and dust off any excess.

Help and Technical Assistance
For assistance, contact CAE Customer Support. Contact information for all regions is available on the back cover of this guide and on the CAE Healthcare website.
Disclaimer
This product is a simulation device designed for training and demonstration purposes only.
Proprietary Notice
This document, including the information contained herein, is confidential and/or proprietary to CAE Inc., and shall not be reproduced or disclosed in whole or in part, or used for any purpose whatsoever without the prior written authorization of CAE Inc.
Trademark Information
Trademarks and/or registered trademarks of CAE Healthcare Inc. and/or its affiliates include but are not limited to: Apollo, Ares, AresAR, Aria, Athena, BabySIM, BluePhantom, Caesar, CathLaVR, EndoVR, HPS, ICCU, InfantSIM, iStan, Juno, LapVR, LearningSpace, Lucina, LucinaAR, Luna, Maestro, METlman, Müse, NeuroVR, PediaSIM, SimEquip, Simulex, StethoSym, SymDefib, SymEyes, UniSIM, Vimedix, VimedixAR and Vivo. All other brands and product names are trademarks or registered trademarks of their respective owners. All logos, tradenames and trademarks referred to and used herein remain the property of their respective owners and may not be used, changed, copied, altered, or quoted without the written consent of the respective owner. All rights reserved. CAE @2022

CONTACT

For more information about CAE products, contact your regional sales manager or the

• CAE distributor in your country, or visit caehealthcare.com.
• • Tel + 1941-377-5562 or 866-233-6384
• For customer support, please contact CAE.
• Customer Support Headquarters – United States
• Monday – Friday from 7:00 a.m. to 6:00 p.m. ET
  • Phone 1-866-462-7920
  • Email: srqcustomerservice@cae.com.
• Customer Support – Canada
• Monday – Friday from 8:00 a.m. to 5:00 p.m. ET
  • Phone 1-877-223-6273
  • Email: can.service@cae.com.
• Customer Support – Europe, Middle East, and Africa
• Monday – Friday from 8:00 a.m. to 5:00 p.m. CET
  • Phone +49 (0) 6131 4950354
  • Email: international.service@cae.com.
• Customer Support – United Kingdom and Ireland
• Monday – Friday from 9:00 a.m. to 5:00 p.m. GMT
  • Phone +44 (0) 800-917-1851
  • Email: uk.service@cae.com.
• Customer Support – Latin America
• Monday – Friday from 9:00 a.m. to 5:00 p.m. BRT/BRST
  • Phone +55 11 5069-1510
  • Email: la.service@cae.com.
• Customer Support – Asia Pacific
• Monday – Friday from 8:00 a.m. to 5:00 p.m. CET
  • Phone +49 (0) 6131 4950354
  • Email: ap.service@cae.com.

©2022 CAE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>