RYOBI 5133001166 Cordless Angle Drill Bit Instruction Manual

Table of Contents

RYOBI-5133001166-Cordless-Angle-Drill-Bit-product

Important: It is essential that you read the instructions in this manual before operating this machine.

Subject to technical modifications.

Wear ear protectors when drilling. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

INTENDED USE

You may use this product for the purposes listed below:

When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste.
The machine, accessories and packaging should be sorted for environmental-friendly recycling.

Safety alert
Volts
Revolutions per minute
Direct current
CE conformity
Conformance to technical regulations
Please read the instructions carefully before starting the machine.
Wear ear protection
Wear eye protection
Recycle
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

ICONS IN THIS MANUAL

RYOBI-5133001166-Cordless-Angle-Drill-Bit-fig-4

RYOBI-5133001166-Cordless-Angle-Drill-Bit-fig-6

RYOBI-5133001166-Cordless-Angle-Drill-Bit-fig-5

Battery and charger

Compatible battery pack (not included): BPP-1815
- BPP-1817
- BPP-1813
Compatible charger (not included): BCA-180
- BC-1815S
- BC-1800
- BCS618
- BCL1418
- BCL14181H
- BCL14183H

All Ryobi products are guaranteed against manufacturing defects and defective parts for a period of twenty four (24) months from the date stated on the original invoice drawn up by the retailer and given to the end user.
Deterioration caused by normal wear and tear, unauthorised or improper use or maintenance, or overload are excluded from this guarantee as are accessories such as battery packs, light bulbs, blades, fittings, bags, etc.
In the event of malfunction during the warranty period, please take the NONDISMANTLED product, along with the proof of purchase, to your retailer or nearest Authorised Ryobi Service Centre.
This warranty in no way affects your legal rights concerning defective products.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may signiﬁcantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signiﬁcantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents.
2006/42/EC, 2004/108/EC, EN55014-1:2006+A1:2009, EN55014- 2:1997+A1:2001+A2:2008, EN60745-1:2009, EN60745-2-1:2010, EN60745-2-2:2010.
Sound pressure level [K=3dB(A)]: 67.5 dB(A)
Sound power level [K=3dB(A)]: 78.5 dB(A)
Weighted root mean
The vibration total values(triax vector sum) determined according to EN60745: Drilling into metal, vibration emission value ah, D = 1.2 m/s2 (Uncertainty K = 1,5 m/s2)
Screwdriving without impact, vibration emission value ah = 0.3 m/s2 (Uncertainty K = 1,5 m/s2)

Techtronic Industries