LUXART Square and Rectangular Shower Wall Kits Instruction Manual

Square & Rectangular
Shower Wall Kits

*Shown with
Optional Corner and Edge Trim

Square and Rectangular Shower Wall Kits

READ THE INSTRUCTIO NS CAREFULLY
Familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how
they are mounted.
COPY THE MODEL NUMBER FOR YOUR RECORDS HERE #

CAUTION: Do not set on corners when handling wall pieces.
NOTE: Optional Corner and Edge Trim pieces are provided in the kit but are not necessary to complete the application of the Shower Wall System. Read through the instruction manual in its entirety to understand how the wall panels can be installed to fit over your existing walls.

PARTS LIST

RECOMMENDED TOOLS

NOTE: SHOWER BASE INSTALLATION
When used in conjunction with a shower base that has a nailing flange, the Shower Wall System is designed to be installed as shown in the drawing.
The nailing flange of the base should be attached directly to the bare studs with backer board attached to the studs above the nailing flange.
The walls are installed on the backer board extending down in front of the nailing flange and resting on the base. Failure to install your base in this configuration may cause problems installing the walls.

PREPARATION TIPS

Before beginning installation of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble or install the product.

• Begin by measuring the overall width of the back wall after it has been cleaned and prepared for installation.
• If the overall height of the back and/or side walls above the bathtub or shower base is less than the height of the panels, they can be easily cut to fit.
• Turn o f the water supply.
• Remove all shower hardware and decorations, including but not limited to: Faucet handles, escutcheons, filler spouts, towel bars, and soap dishes.
• All plumbing and electrical work inside the walls must be finished prior to installing the wall panels.
• Walls should be solid, plumb, and square within 1/8 inch of true. The Shower Wall System has been designed to allow for trimming, to accommodate minor alignment problems.
• The mounting surface should be cleaned and prepared, according to the Installation Procedure.
• If you plan to install a recessed accessory, cut the panel accordingly after it has been fully installed, and had the proper time to adhere to the wall. Remember to be considerate of wall studs when positioning the accessory.

CAULKING TIPS:

• Follow the instructions on the tube of your chosen caulk.
• Once you have completed the project, inspect all areas that have been caulked, filling in any gaps as needed.
• Remove any excess caulk using denatured alcohol and a clean cloth. Use caution, and do not to disturb any of the caulk joints.

INSTALLATION PROCEDURE:
The Shower Wall System can be installed over a variety of products. Consult with a professional contractor if you intend to apply the panels to any surface other than those described here.

CEMENT/CONCRETE:

• Depending on the condition (flatness) of the existing wall, additional silicone may be required to properly secure the wall panels to the substrate.
• Surface must be completely clean. This includes but not limited to:Soap scum, dust and any other contaminates that may afect adhesion. Ceramic tiles do not need to be removed, if solidly adhered.
• Recommended: The complete area sealed with two coats of water or oil-based sealer, to ensure proper adhesion of the Shower Wall System.
• Complete the installation of the wall panels following the instruction manual, after the sealer has completely dried.

MASONITE:

• Surface must be completely clean. This includes but not limited to: Soap scum, dust and any other contaminates that may afect adhesion.
• Optional: The complete area sealed with two coats of water or oil-based sealer, to ensure proper adhesion of the Shower Wall System.
• Complete the installation of the wall panels following the instruction manual, after the sealer has completely dried.

OLD TILE:
IMPORTANT: All plastic tiles must be removed. Old ceramic tiles do not need to be removed, if solidly adhered.

• Depending on the condition (flatness) of the existing wall, additional silicone may be required to properly secure the wall panels to the substrate.
• Properly remove and or reattach any loose ceramic tiles.
• Remove all tile accessories attached to the wall. Surface must be completely clean. This includes but not limited to soap scum, dust and any other contaminates that may afect adhesion.
• Complete the shower wall installation by following the instruction manual.

PLASTER:

• Additional silicone may be required to properly secure the substrate and the wall panel, depending on the condition of the existing wall.
• Smooth all textured and/or swirled finishes by sanding.
• Surface must be completely clean. This includes but not limited to soap scum, dust and any other contaminates that may afect adhesion.
• Recommended: The complete area sealed with two coats of water or oil-based sealer, to ensure proper adhesion of the Shower Wall System.
• Complete the installation of the wall panels following the instruction manual, after the sealer has completely dried.

SHEETROCK/GREENBOARD/CEMENT BOARD/ WOOD:

• Surface must be completely clean and free of soap scum, dust, and any other contaminates that may afect adhesion.
• Optional: The complete area sealed with two coats of water or oil-based sealer, to ensure proper adhesion of the Shower Wall System.
• Complete the installation of the wall panels following the instruction manual, after the sealer has completely dried.

INSTALLATION PROCEDURE

STEP 1
1 MEASURING

1. Measure the height of installation area at both ends of each wall. From top of tub or shower pan to the ceiling. If the ceiling height is less than the height of the panels included in your kit, the panels can be cut down using the same cutting procedure outlined in Step 2.

2. Measure width of each wall at top and bottom of installation area.
   Important Note: Steps 2 &3 will be repeated when installing each of the 5 wall panels.
   

3. Measure cut-out locations for plumbing fixtures and mark them on the back of the appropriate panel(s).
   

STEP 2
2 CUTTING
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.
The following cutting instructions should be used when making all cuts.

Cutting Panels to Size:

1. Carefully draw a line on the back of each panel where the cut is to be made. Any adjustments for out of square or out of plumb should be considered when drawing this line.
   Note: Using a straight edge when possible is highly recommended

2. Circular saw is recommended for making required cuts. If using utility knife, score the line several times and then use locking pliers to snap off the excess piece as shown.
   

Plumbing Cut-Outs:
Use a drill and the appropriate size hole saw to create cut-outs for the shower head, filler spout, faucet handles and/or any other cutouts necessary for plumbing that is already in the walls.
Note: To be sure your measurements are correct, make a cardboard template to test the plumbing cutouts prior to cutting the JETCOAT®panels.
Important: Drill chuck can damage the Jetcoat® wall panel surface. Drill holes from back side of panel.

Recessed Accessories:
If you plan to install a recessed accessory, cut the panel accordingly after it has been fully installed, and had the proper time to adhere to the wall.Remember to be considerate of wall studs when positioning the accessory.

STEP 3
3 APPLYING ADHESIVE AND TAPE TO BACK SIDE OF WALL PANELS
The following instructions should be used when applying tape and adhesive to each wall panel.

1. Apply double-sided construction tape to the back of the wall panel as shown.
2. Apply construction grade adhesive to the spaces between the tape as shown in a circular pattern.
   The beads of adhesive should be 2″ apart and up to, but no closer than 1″ from the panel edge.
   Important: The circular pattern is critical for proper adhesion.
   

STEP 4
4. INSTALL LEFT BACK WALL PANEL
Important Note: Failure to install the back wall panels in the correct order may cause the pattern across the back wall not to appear continuous.
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.
Note: Your kit contains 3 back wall panels (labeled on the back as (3)First Panel, (3)Second Panel and (3)Third Panel) and two end panels (labeled (4) Right Panel & (4) Left Panel).

1. Locate the panel labeled (3)First Panel and lay it down on a flat surface.

2. Based on your measurements from Step 1(Measuring) cut the panel to the appropriate size and make any required plumbing cut-outs according to the instructions in Step 2 (Cutting).
   IMPORTANT: If you are using the optional corner trim or not, be sure to measure and cut appropriately for the existing space needed to complete your corner. You may have to cut more or less of the tongue to ensure proper fit and finish.

3. Apply the double-sided tape and construction adhesive as explained in Step 3.

4. Optional Corner Trim
   If using the optional corner trim, apply construction adhesive to the backside of the internal corner trim and push it into place as shown (left corner only at this time). Important: Corner Trim should not be used if the corner is more than 1/4″ out of square.

5. Peel o f back of double-sided tape from the back of the panel. Position the panel at approximately 30 degrees, push the cut edge into the corner and then carefully push the panel towards the back wall.
   5. Optional Corner Trim Peel of back of double-sided tape from the back of the panel. Fill the channel with caulk, then position the panel at approximately 30 degrees, push the cut edge into the channel and then carefully push the panel towards the back wall.

6. Push panel firmly against the wall smoothing out any air bubbles along the entire area and then lightly tap on wall panel with a rubber mallet from top to bottom to ensure it is tightly connected to the wall.

STEP 5
5 INSTALL BACK CENTER WALL PANEL
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.

1. Locate the panel labeled (3)Second Panel and lay it down on a flat surface.

2. Based on your measurements from Step 1(Measuring) trim the height, if necessary, and make any required plumbing cut-outs according to the instructions in Step 2 (Cutting).

3. Apply the double-sided tape and construction adhesive as explained in Step 3.

4. Peel of back of double-sided tape from the back of the panel. Position the panel at an angle of approximately 45 degrees, and carefully push the tongue edge into the groove in the trailing edge of the (3) First Panel. Move the panel gently while exerting forward pressure and carefully push it toward the back wall.
   Important Note: Great care must be taken when installing this panel. The watertight seal depends on the tongue being firmly inserted into the groove before the panel is pushed back into position and height alignment cannot be adjusted once the panel clicks into place.

5. Press against the wall smoothing out any air bubbles along the entire area and then lightly tap on wall panel with a rubber mallet from top to bottom to ensure it is tightly connected to the wall.
   

STEP 6
6 INSTALL BACK RIGHT WALL PANEL
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.

1. Locate the panel labeled (3)Third Panel and lay it down on a flat surface.

2. Based on your measurements from Step 1(Measuring) cut the panel to the appropriate size and make any required plumbing cut-outs according to the instructions in Step 2 (Cutting).
   IMPORTANT: If you are using the optional corner trim or not, be sure to measure and cut appropriately for the existing space needed to complete your corner. You may have to cut more or less of the tongue to ensure proper fit and finish. We strongly recommend that you re-measure to verify your final panel width before cutting this panel.

3. Apply the double-sided tape and construction adhesive as explained in Step 3.

4. Peel of back of double-sided tape from the back of the panel. Position the panel at an angle of approximately 45 degrees, and carefully push the tongue edge into the groove in the trailing edge of the (3) Second Panel. Move the panel gently while exerting forward pressure and carefully push it toward the back wall.
   Important Note: Great care must be taken when installing this panel. The watertight seal depends on the tongue being firmly inserted into the groove before the panel is pushed back into position and height alignment cannot be adjusted once the panel clicks into place.
   

5. OPTIO NAL CORNER TRIM
   Apply caulk to both back edges of the internal corner piece. Fill the channel that the back panel will fit into with caulk. Insert the optional internal corner trim 45° into the end side of wall panel. Use a flathead screw driver to exert forward pressure and snap in with ease. Make sure the corner trim is tightly attached to the wall panel and corner of wall.

6. Press against the wall smoothing out any air bubbles along the entire area and then lightly tap on wall panel with a rubber mallet from top to bottom to ensure it is tightly connected to the wall.

STEP 7
7 INSTALL LEFT WALL PANEL
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.

1. Locate the panel labeled (4) Left Panel and lay it down on a flat surface.

2. Based on your measurements from Step 1(Measuring) cut the panel to the appropriate size and make any required plumbing cut-outs according to the instructions in Step 2 (Cutting).
   IMPORTANT: If you are using the optional corner trim or not, be sure to measure and cut appropriately for the existing space needed to complete your corner. You may have to cut more or less of the tongue to ensure proper fit and finish.

3. Apply the double-sided tape and construction adhesive as explained in Step 3.

4. Peel of back of double-sided tape from the back of the beveled edge wall panel.

5. Position the panel at approximately 30 degrees, push the panel edge into the corner and then carefully push the panel back towards the wall.
   5. O PTIONAL CORNER TRIM
   Fill the channel of the corner piece that the panel will fit into with caulk. Position the panel at approximately 30 degrees, push the panel edge into the channel and then carefully push the panel back towards the wall.

6. Press against the wall smoothing out any air bubbles along the entire area and then lightly tap on wall panel with a rubber mallet from top to bottom to ensure it is tightly connected to the wall.

STEP 8
8 INSTALL RIGHT SIDE WALL PANEL
Important Note: The arrows on the label on the back of each panel indicate the TOP of the Panel.

1. Lay (4) Right Panel down on a flat surface.

2. Based on your measurements from Step 1(Measuring) cut the panel to the appropriate size and make any required plumbing cut-outs according to the instructions in Step 2 (Cutting).
   IMPORTANT: If you are using the optional corner trim or not, be sure to measure and cut appropriately for the existing space needed to complete your corner. You may have to cut more or less of the tongue to ensure proper fit and finish.

3. Apply the double-sided tape and construction adhesive as explained in Step 3.

4. Peel of back of double-sided tape from the back of the beveled edge wall panel.

5. Position the panel at approximately 30 degrees, push the panel edge into the corner and then carefully push the panel back towards the wall.
   5. O PTIONAL CO RNER TRIM
   Fill the channel of the corner piece that the panel will fit into with caulk. Position the panel at approximately 30 degrees, push the panel edge into the channel and then carefully push the panel back towards the wall.

6. Press against the wall smoothing out any air bubbles along the entire area and then lightly tap on wall panel with a rubber mallet from top to bottom to ensure it is tightly connected to the wall.

FINISHING
9 OPTIONAL: INSTALL EDGE TRIM

1. Measure and cut (2) Edge Trim for length and to cover tile or existing wall material as needed.
2. Fill the channel that the wall panel will slide into with caulk and apply construction grade adhesive to the back of the Edge Trim piece.
   Carefully position the Edge Trim and push it into place.
   

10 CAULK CORNERS AND EDGES
Properly caulk around the Shower Wall System to insure a secure fit and finish.
This includes but is not limited to:

• Interior corners where shower walls meet (Not necessary if optional corner pieces were used).
• Corners where the walls meet the base.
• Outer edge of Side Wall Panels (Not necessary if optional edge pieces were used).
• (Optional) Caulking along the top edge of the entire enclosure is not required but may help contribute to a finished look.

Important Note: Please keep the entire area dry for a minimum of 24 hours to allow the caulk and construction adhesive to properly cure.

Warranty

The distributor warrants to the original purchaser that this fixture will be free of manufacturing defects, which affect its performance as a bathing or showering fixture, under the following conditions and subject to the limitations contained in the “Remedies” and “Warranty Limitations” sections. The Limited Warranty applies for 10 years from the date of purchase if the fixture is used in a residential owner-occupied building for non-commercial purposes or for 2 years from the date of purchase if it is used in any other building, including any building used for rental, commercial or business purposes. This Limited Warranty is void if the fixture is not installed in accordance with the installation instructions supplied by the distributor, or local building codes and ordinances, or if the care and cleaning instructions supplied by the distributor are not followed This Limited Warranty is also void if the fixture is moved from the location of its initial installation or is subjected to accident, abuse, or misuse. The Limited Warranty excludes normal wear and tear. This Limited Warranty shall be void unless any failure or non-conformance is discovered before the expiration of this warranty, and is reported to the distributor, in writing, accompanied by the original proof of purchase, within 30 days of discovery. REMEDIES – The original purchaser’s remedy under this Limited Warranty is limited to the repair, replacement or refund of the purchase price of the fixture, at the distributor’s sole option, of any part of the fixture that has failed or does not conform to the manufacturer’s specifications, limited to, damage to or loss of use of the building or its contents, arising out of any defect in the fixture nor shall the distributor be liable for any amount in excess of the original purchase price of the fixture. The distributor reserves the right to require the return, at purchaser’s expense, of the damaged fixture for repair or exchange before providing services under this Limited Warranty. If the distributor elects to replace the fixture, its obligation is limited to supplying a replacement unit or component part of comparable size and style, and does not include the cost of removal, installation or transportation, which must be borne by the purchaser. Replacement parts provided under this Limited Warranty are warranted for the remainder of the original warranty period applicable to the fixture, as if such parts were original components of that fixture. WARRANTY LIMITATIONS – THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. THE DISTRIBUTOR DISCLAIMSANYANDALLLIABILITY FOR SPECIAL, INCIDENTALOR CONSEQUENTIAL DAMAGES. Some states do not allow limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you. In such states, the distributors’ liability shall be limited to the extent permitted by state law. ANY IMPLIED WARRANTIESARISING BY WAYOF STATE LAW, INCLUDINGANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED IN DURATIONAND IN SCOPE OF COVERAGE TO THE TERMS OF THIS LIMITED WARRANTY, UNLESSASHORTER PERIOD ISALLOWED BY LAW.

ATTENTION CONSUMER:
IMPORTANT WARRANTY INFORMATION
PLEASE DO NOT DISCARD
Thank you for your purchase.
In order to be eligible for product warranty, please register your door on our website within two (2) weeks of installation.
Go to:
https://www.luxartcollection.com/pages/register-warranty
Or scan the QR Code below and follow the instructions.

https://qrco.de/lxwarranty

For any questions or comments about your purchase, please contact our Customer Service at:
[email protected]

Need Help? Please call our toll-free customer service line at 1-225-295-4212 for additional assistance or service. If you have any questions or concerns regarding our warranty plan, please email: [email protected], Monday-Friday 7:30 AM to 5:00 PM EST

Revised 11/29/22

References

• Register Your Luxart® Warranty – Luxart Collection

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>