DJPOWER WP-1S Bubble Fogger Machine User Manual

: June 12, 2024
: DJPOWER

DJPOWER WP-1S Bubble Fogger Machine

BEFORE YOU BEGIN

What Is Included

WP-1S bubble fogger × 1
Power Cord × 1
Warranty Card×1

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.

Symbols

Symbol	Meaning
** _Caution

_ Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
| Important
Important installation or configuration information. Failure to comply with this information may keep the product from working correctly.
| Information
** Useful information.

Disclaimer

The information and specifications contained in this User Manual are subject to change without notice.
DJ POWER assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time. Copyright© 2019 DJ POWER. All rights reserved.

Safety Notes

Please read the following Safety Notes carefully before working with the product The notes include important safety information about installation, usage, and maintenance.

Personal Safety

Always connect the product to a grounded circuit to avoid the risk of electrocution.
Make sure that children, unauthorized people and animals do not obtain access to the machine.

Mounting and Rigging

The product is for indoor use only! To prevent risk of fire or shock, do not expose the product to rain or moisture.
CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
Do not mount the product on a flammable surface (linoleum, carpet, wood, paper, carton, plastic, etc.).
Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are blocked or clogged by dust. If necessary, remove the dust.

Power and Wiring

Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product.
Make sure the power cord is not crimped or damaged.
Never connect this product to a dimmer pack or rheostat.
Never disconnect the product from power cord by pulling or tugging on the cord.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Operation

Do not operate this product if you see damage to the housing or cables. Have the damaged parts replaced by an authorized technician at once.
Do not use the product as a space heater.
The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher temperatures.
Do not cover the ventilation slots when operating to avoid internal overheating.
Do not cover or plug the output nozzle during operation.
Wipe up spitted fluid immediately. Moisture – also fluid – can destroy the electric.
Never carry the product by the power cord or any moving part. Always use the handles of the machine.
Drain the tank before transporting the product. Bubble fluid or the fog fluid tanks shall be used for the relevant fluid only.
Always disconnect the product from the power source before cleaning.
In the event of a serious operating problem, stop using the product immediately.
This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained, certified technicians. Do not open the housing or attempt any repairs which can lead to damage or malfunction.
Use only DJPOWER Consumable. Bubble fluid PRO-P and fog fluid PRO-Care recommended.

Keep this User Manual for future use. If you sell the product, be sure that the purchaser receives this document.

INTRODUCTION

Description

WP-1S bubble fog machine is the first bubble blaster from DJPOWER. It comes with patented Jet-design which makes lot of vivid bubbles filled with fog with less fog outside. The excess bubble fluid will flow to waste storage bin instead of dropping on the ground. To protect bubble fluid from getting bad and ensure high quality bubbles, bubble fluid is well stored in the tank. With this feature, the unit can also be mounted high in the truss, launching bubbles all over the sky. No matter for shows , concerts ,parties and events , this unit will be pretty good choice.

Features

Jet design, produce lots of bubbles filled with fog.
Well-designed heating system releases the fog evenly and purely, no fluid dropping off.
The fan make the fog bubble fly higher, further.
Bubble and fog fluid storage in separately.
The excess bubble fluid will flow back to waste fluid tank.
Built-in LCD control ,3-pin and 5-pin OMX control.

Product Overview

Product Dimensions

TECHNICAL SPECIFICATIONS

AC Power	Input Voltage & Rate	AC 220-240 V, 50/60 Hz
Current Limiter Type	FUSE
Current Limiter Specifications	F 5 A, 250 V
Total Power Consumption	600 W
Heating	Heat Up Time	Appr. 4 min
Capacity	Bubble Fluid Tank Capacity	1.3 L
Fog Fluid Tank Capacity	1.3 L
Output	Adjustable Output	√
Max Fog Output Volume	Appr. 4,500 cfm
Max Output Height	Appr. 3 m
Max Output Distance	Appr. 3.3 m
Fog Fluid Consumption (100% Output）	Appr. 60 min/L
Bubble Fluid consumption (100% Output)	Appr. 50 min/L
Consumable Type for Standard Output Test	PRO-P and PRO-C
Placement & Mounting	Horizontal	√
Inclined	×
Sidelong	×
Hang Upside Down	×
Rigging & Trussing	√
Control	Wireless Control	On-device Control Panel
Wired Control	×
Control Protocol	×
Control Protocol	DMX512
DMX Channel Range	4
Consumable	Consumable	PRO-P and PRO-C
Weight & Dimensions	Net Weight	9 kg
Gross Weight	10.5 kg
Machine Dimensions	312 × 310 × 394 mm
Packing Dimensions	405 × 405 × 480 mm

SETUP

AC Power

The machine has a fixed voltage power supply and can work with an input voltage of AC 110V-120V, 50/60Hz or AC 220 V-240 V, 50/60 Hz, depending on the specific model.

To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart The listed current rating indicates the product’s average current draw under normal conditions.

Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a Oto 100% switch.

DMX Linking

You can link the WP-1S to a DMX controller using a 3- or 5-pin DMX connection. If using other DMX-compatible products with this product, you can control each individually with a single DMX controller. Instructions for connecting and configuring this product for DMX operation are in the User Manual.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation

For safety reasons, we do not recommend mounting the product in any capacity. Operate the product while it is on the ground only, and make sure there is adequate room for ventilation, configuration, and maintenance.

Do not mix bubble fluid and fog fluid.

Rigging

DJ POWER recommends using the following general guidelines when mounting this product.

Before deciding on a location for the product, make sure there is easy access to the product for maintenance and programming purposes.
Make sure that the structure or surface onto which you are mounting the product can support the product’s weight (see the Technical Specifications).
When mounting the product on the floor, make sure that the product and cables are away from people and vehicles.

OPERATION

Preparing for Operation

After checking that all the parts are intact and complete, position the machine on flat.
Withdraw the fluid tank from its compartment and remove its cap.
Verify that the plastic hoses attached to the cap are in place and in good condition without bending or warp.
Always connect the product to a grounded circuit Before power on, make sure it is connected with the rated voltage.
Turn on the machine, and”Ul.0″shows on the Digital display tube and then show” HEAT” immediately during the heating-up process. After approx.4 minutes, the Digital display tube changes to “ADDR” when the machine is ready to output

On-device Control Panel

To access the control panel functions, disconnect the OMX signal, and use the four buttons located underneath the Digital display tube.

Button	Function
< MENU>	Switch menu pages to select a function
< ▲ >	Increases the numeric value of current function
< ▼ >	Decreases the numeric value of current function
< ENTER>	Save settings

STOP turns the fog output off
In any pages, press ENTER in 2 seconds, go back to main page “ADDR”

Menu Map

Digital display tube	Description
Addr	Press UP or DOWN to set DMX address 1~512

In any interface, if no button is pressed within 10S, the display will return to the “Addr” page;
In any interface, if the button is not pressed within 30S, the black screen will be displayed; if any button is pressed again, the “Addr” page will be showed;

B| Press E N T E R to enter into the bubble mode, and then press ▲ or ▼ to set Bubble output

ON /OFF

H| Press E N T E R to enter into the haze mode, and then press ▲ or ▼ to set haze volume

OFF, 1%~100%

F| Press E N T E R to enter into the fan, and press ▲ or ▼ to set fan speed 0~3
CLE| Press E N T E R to enter into clear mode, and then press ▲ or ▼ to set cleaning mode

ON/OFF

DMX Mode Menu Map

When the machine connects to DMX, the digital display tube will always show ADDR setting page, and you can set or change it at any time by pressing UP or DOWN button.

DMX Channel Assignments and Values DMX

1	Bubble Output	000-010	OFF
011-255	ON
2	Fog Output	000-010	OFF
011-255	Fog volume, low to high
3	Wind Output	000-010	OFF
11-100	Fan speed Low
101-200	Fan speed Middle
201-255	Fan speed High
4	Bubble cleaning mode	000-010	OFF
011-255	Bubble cleaning mode ON, overriding other functions

TECHNICAL INFORMATION

Maintenance

After each time use of the bubble fog machine, it is necessary to clean the fog head with clean water in time to prevent the residual bubble liquid on the fog head from solidifying and gluing, which will cause it to fail to be used normally next time!

Do not allow the WP-1S to become clogged due to the sticky bubble fluid. Cleaning and maintenance are necessary.

The recommended cleaning procedure is as follows.

Unplug the product from power.
Empty bubble fluid from the machine.
Add water to the bubble fluid tank.
Connect the product to power and allow it to warm up. Run the Cleaning Mode through Menu or OMX.
Thoroughly rinse the Bubble fluid reservoir.
Run the product in a well-ventilated area. Do not allow the pump to run dry.
Excessive dust, fluid residue and dirt will degrade performance and cause overheating. Remove dust from air vents with air compressor, vacuum or soft brush. The casing could be cleaned by the damp cloth.
Restore the hoses and cap. Store the unit until next use.

The default cleaning time is 1 minute. Without turning of the cleaning mode manually, it will shut of automatically after 1 minute.

Test-run your DJ POWER® WP-1S on a monthly basis to achieve the best performance.

STORAGE

Machine Storage

Before storing the machine, clean it as described in the cleaning procedure above; however, only follow steps 1 through 5. Do not refill the tank with fog fluid if storing the machine. Empty both the bubble and haze fluid tank. Cleaning the system prior to storage will help prevent any particles from condensing inside the pump or heater while not in use.

WWW.DJPOWER.cn