PMK FF-HAL10kV Probe Positioners Instruction Manual
- June 12, 2024
- PMK
Table of Contents
Probing Solutions.
Made in Germany.
FireFly® Probe Positioners
Hands-free Testing
0 °C to +50 °C
Instruction Manual
FireFly® Probe Positioners
The FireFly® probe positioners offer precise and semi-permanent positioning for FireFly® optically isolated probes, minimizing the risk of unwanted movement that could damage the device under test or result in an unsafe condition. These positioners act as a reliable “third helping hand”. One of the key advantages of the FireFly® probe positioners is their quick and easy setup process, saving valuable time and effort by moving the probe into the desired position and holding it securely in place.
Specifications
FireFly® products are not rated for CAT II, III or IV. Do not exceed the
specifications. Review also the the FireFly® Series Instruction Manual. The
following ratings are according to IEC 61010-031:2023-05.
Electrical Specifications of FF-HAL10kV and FF-3DPOS200
Rating for Measurement Category not II, III or IV:
| Maximum Rated Insulating Voltage| 10 kV (DC + Peak AC)
---|---|---
Pollution Degree| 2
Electrical Specifications of FF-2FOOTER
Rating for Measurement Category not II, III or IV:
| Maximum Rated Insulating Voltage| 30V AC / 60V DC
---|---|---
Pollution Degree| 3
Environmental Specifications
Altitude | Operating | up to 2000 m |
---|---|---|
Non-operating | up to 15000 m | |
Temperature Range | Operating | 0 °C to +50 °C |
Non-Operating | -40 °C to +71 °C | |
Maximum Relative Humidity | Operating | 80 % relative humidity for temperatures |
up to +31 °C, decreasing linearly to 40 % at +50 °C
Non-operating| 95 % relative humidity for temperatures up to +40 °C
Maintenance and General Notes
**** The 3D Probe Positioners are almost maintenance-free. However, if the
device is exposed to pollution, regular cleaning is necessary. Remove dust and
dirt from the joints.
Make sure to use any FireFly® probe positioner in a clean lab environment
without any pollution, dust or dirt to maintain the specified isolation
voltage.
For cleaning purposes use standard cleaning agents commercially available.
Don`t use any lye or acids.
Apply a little amount of lubricant to the screws and joints, as needed.
Scope of Delivery
- FireFly® Positioning System (FF-3DPOS200) including Wrench 7mm, FireFly® Probe Head Holder Set FF-HAL10kV-3 or FireFly® 2-Footer (FF-2FOOTER)
- instruction Manual
Getting Started
Read also the FireFly® Instruction Manual before first use, and keep both for
future reference. A digital copy of the latest Instruction Manual revisions
can be downloaded at www.pmk.de. The use of this equipment is for qualified
personnel only. Observe adequate spacing between FireFly® probe head
components and earth ground. Note, FireFly® products are not rated for CAT II,
III or IV. To achieve the most accurate measurement results, review the
“Getting Started” section in the FireFly® Series Instruction Manual.
Clamping the FireFly® Probe (all models)
Insert the FireFly® probe from the top into the holder. Before turning the
FireFly® probe by 90° to mount or unmount, make sure the probe is fully
inserted and seated into the holder. The following example is also valid when
using the bi-pod FF-2FOOTER. **** The FireFly® probe holders consist of
insulating material. Only the holder FF-HAL10kV, which is equipped with the 3D
probes positioner FF-3DPOS200, provides isolation voltages up to 10kV. Observe
the required distances of FireFly® probe head to earth ground.
Using the Holders FF-3DPOS200 and FF-HAL10kV
- Assembly
Screw the positioner arm [B] into the product specific base [A] with M6 thread, and tighten it with the 7mm wrench from the scope of delivery. The base [A] is available in three different variants: Steel base, vacuum base or table clamp. The positioner arms [B] with M6 thread are available with 130mm and 200mm span width.
The probe holder [C] shape depends on the probe being in use. For the FireFly® Series use the FF- HAL10kV only. The drawing below shows as example of the universal probe holder.
- Handling and Re-Positioning
Hold the 3D Probe Positioner and loosen the central tensioning knob [D] until the 3D Probe Positioner can be moved.
**** Do not release the tensioning knob [D] completely, otherwise the 3D
Probe Positioner collapses in itself and could damage your measuring setup.
If you are using MMCX as the input connector, disconnect the MMCX connector
from the circuit under test before repositioning the probe and its holder,
otherwise you may cause unnecessary mechanical stresses on the MMCX connector
and the PCB.
Bring the 3D Probe Positioner into the desired position and fix the device by
turning the central tensioning knob [D] contrary.
Ordering Information
All components are compatible with parts from the PMK positioning systems series. If a 3D positioning system from PMK is available already, only the FireFly® probe holder FF-HAL-10kV is needed. For spare parts and more positioners, visit us at www.pmk.de
Order No. | Item | Picture |
---|---|---|
FF-3DPOS200 | FireFly® 3D Probe Positioner for 10kV Insulation with steel base |
(893-100-001), arm with span width 200mm (893-200-200), FireFly® probe holder
(FF-HAL10kV), Wrench 7mm|
FF-HAL10kV| FireFly® Series non-conducting High Voltage Differential Probe
Holder for 10kV Voltage Insulation, M6 thread, pack of three|
893-000-SW7| Wrench 7mm – spare part|
FF-2FOOTER| FireFly® Probe Holder 2-Footer (Bipod) – spare part|
Copyright © 2023 PMK – All rights reserved.
Information in this publication supersedes that in all previously published
material.
Specifications are subject to change without notice.
Manufacturer
PMK Mess- und Kommunikationstechnik GmbH
Königsteiner Str. 98
65812 Bad Soden, Germany
Tel: +49 (0) 6196 999 5000
Internet: www.pmk.de
E-Mail: sales@pmk.de
Warranty
PMK warrants this product for normal use and operation within specifications
for a period of one year from date of shipment and will repair or replace any
defective product, which was not damaged by negligence, misuse, improper
installation, accident or unauthorized repair or modification by the buyer.
This warranty is applicable only to defects due to material or workmanship.
PMK disclaims any other implied warranties of merchantability or fitness for a
particular purpose. PMK will not be liable for any indirect, special,
incidental, or consequential damages (including damages for loss of profits,
loss of business, loss of use or data, interruption of business and the like),
even if PMK has been advised of the possibility of such damages arising from
any defect or error in this manual or product.
M-FF-POSITIONERS
Revision 01-2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>