RYOBI RY18SCXA Cordless Secateurs Instruction Manual

RYOBI RY18SCXA Cordless Secateurs

Product Information

The product is a cordless secateurs designed for cutting and pruning small wood limbs and branches. It has a maximum cutting capacity of 28 mm for softwood and 25 mm for hardwood. The product should not be used to cut branches with diameters greater than these values.

Important:  It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Subject to technical modification.

Safety, performance, and dependability have been given top priority in the design of your cordless secateurs.

INTENDED USE

The cordless secateurs are designed for cutting and pruning small wood limbs and branches with a diameter of up to 28 mm (softwood) and 25 mm (hardwood). Do not cut branches with diameters that are greater than these values. Do not use the product for any other purpose.

GENERAL PRODUCT SAFETY WARNINGS

WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re, and/or serious injury. Save all warnings and instruction for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) product or battery-operated (cordless) product.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks, which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injury.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorised service providers.

CORDLESS SECATEURS SAFETY WARNINGS

DANGER:  Keep hands away from the blade. Contact with the blade will result in serious personal injury.

WARNING: Do not leave the product unattended before the LED and sound indicate that it is off.

• Save these instructions. Refer to them frequently, and use them to instruct others who may use the product. If you loan someone the product, loan them these instructions also to prevent misuse of the product and possible injury.
• Never allow children, persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, or people who are unfamiliar with these instructions to use the product. Local restrictions may limit the age of operator.
• Do not operate the product in poor lighting. Use the product only in daylight or good artificial light.
• To reduce the risk of injury associated with contacting moving parts, always turn off the product, remove the battery pack, and make sure that all moving parts have come to a stop:
  • before clearing a blockage
  • before checking, cleaning, or working on the product
  • before changing accessories
  • before leaving the product unattended
  • before performing maintenance
• Keep the product clean of clippings and other materials. They may become lodged between the jaw and blade.
• Keep the area clear of all bystanders, children, and pets while operating the product.
• When cutting a limb under tension, be alert for spring back so that you will not be struck when the tension in the wood fibres is released.
• Maintain the product with care. Keep the cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow the instructions for lubricating and changing accessories.
• Before using the product, check for damaged parts and press the trigger to ensure that the blades open and close correctly. Before further use of the product, any part that is damaged must be carefully checked to determine that it will operate properly and perform its intended function. Keep hands away from the blade.
• Keep your body warm in cold weather. When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
• Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure that you take regular breaks.
• If the blade is stuck in a branch during operation, do not twist the blade. Turn off the product and pull the blades straight out slowly from the branch.
• Cut branches one by one.
• Never hold the branch you are pruning with your free hand. Keep hands and any other part of the body away from the cutting area. Never touch the blades to avoid injuries.
• Do not grasp the exposed cutting blades when picking up or holding the product.
• Do not use the product in rain or snow.
• Do not use the product to cut wires.
• Do not cut where there is a risk of hidden wiring.
• Operate the product only in temperatures between 0°C and 40°C.
• Store the product in a location where the ambient temperature is between 0°C and 40°C.
• Cut at an angle for a cleaner cut.
• The temperature of the product may rise, and overtemperature protection may be activated when cutting very dry or hard materials. Wait for 10-15 minutes or until the product has cooled down before resuming operation.

ADDITIONAL BATTERY SAFETY WARNINGS

• To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse the tool, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
• Charge the battery pack in a location where the ambient temperature is between 10°C and 38°C.
• Store the battery pack in a location where the ambient temperature is between 0°C and 40°C.
• Use the battery pack in a location where the ambient temperature is between 0°C and 40°C.

TRANSPORTATION AND STORAGE

• Turn off the product, remove the battery pack, and allow both to cool before storing or transporting.
• Remove all foreign materials from the product. Install the blade cover.
• Always install the blade cover when storing or transporting the product.
• For transportation in a vehicle, secure the product against movement or falling to prevent injury to persons or damage to the product.
• Store the product in a cool, dry, and well-ventilated place that is inaccessible to children. Keep the product away from corrosive agents such as garden chemicals and deicing salts. Do not store the product outdoors.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national provisions and regulations. Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, nonconductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

• Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, can contribute to poor performance, and may void your warranty.
• Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. Have the product serviced by an authorised service centre only. When servicing, use only original replacement parts.
• After each use, clean the body and handles of the product with a soft, dry cloth. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
• After each use, clean the debris from the blades with a stiff brush, and then use a disinfectant wipe to clean the blades. Carefully apply a rust-preventative lubricant. Use a recommended rust-preventative lubricant spray to apply an even distribution and reduce the risk of personal injury from contact with the blades. For information about suitable spray products, check with your local authorized service centre.
• You may make adjustments and repairs described in this manual. For other repairs, contact an authorised service centre.
• Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure that the product is in safe working condition.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, or grease. Do not at any time let brake fluids, gasoline, petroleumbased products, or penetrating oils come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, resulting in serious personal injury.
  • NOTE: To ensure long and reliable service, carry out the following maintenance regularly:
  • Check for obvious defects, such as loose, dislodged, or damaged blades; loose fixings; and worn or damaged components.
  • Visually check the condition of the cutting edges of the cutting blade. Replace the blade when worn or damaged.
• To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance. Ensure that the cutting mechanism has stopped before setting the product down and storing the product.

LED INDICATIONS

KNOW YOUR PRODUCT

1. Blade washer
2. Screw
3. Cutting blade
4. LED indicator
5. Handle
6. Trigger switch
7. Blade knob
8. LED Light
9. Fixed blade
10. Blade cover
11. Operator’s manual
12. Battery pack
13. Charger
14. Holster
15. Replacement cutting blade
16. Light lubricant oil
17. Sharpening tool

SYMBOLS ON THE PRODUCT

• Safety alert
• Read and understand all instructions before operating the product. Follow all warnings and safety instructions.
• European Conformity Mark
• EurAsian Conformity Mark
• Ukraine Conformity Mark
• British Conformity Mark
• Waste electrical products should not be disposed of with household waste.
• Please recycle where facilities exist.
• Check with your local authority or retailer for recycling advice.
• Wear head and eye protection.
• Do not expose to rain or damp condition.
• To prevent serious injury, do not touch cutting blades.
• Beware of thrown or fl ying objects.
• Keep all bystanders, especially children and pets, at least 15 m away from the operating area.
• Visible radiation, instructional safeguard
• Press and hold the trigger for 3 seconds to turn the product on or off.
• The product goes into sleep mode if the trigger is not pressed for more than 30 seconds.

SYMBOLS IN THIS MANUAL

• Note
• Warning

Precautions

Overview

Using Instructions

Product specifications

• Cordless secateurs
• Model
• Rated voltage
• Cutting capacity (hardwood)
• Cutting capacity (softwood)
• Cutting cycle time
• Product length (without battery pack)
• Weight without battery pack
• Weight with the heaviest battery pack
• Noise emission level (in accordance with EN 62841-1)
• A-weighted sound pressure level at the operator’s position
• Uncertainty
• A-weighted sound power level
• Uncertainty
• Vibration level (in accordance with EN 62841-1)
• Vibration total value
• Uncertainty

Battery and charger

• Model
• Battery pack
• Weight
• Charger
• Compatible battery packs
• Compatible chargers

Replacement parts

• Replacement blade

NOTE: Visit your local special orders desk or contact RYOBI Customer Service for replacement parts.

WARNING

The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of exposure.

The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may significantly increase the exposure levels over the total working period. An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is running idle. These conditions may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the accessories, keeping the hands warm (in case of vibration), and organising work patterns.

WARRANTY

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newlyacquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   • any damage to the product that is the result of improper or lack of maintenance
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any product not displaying the CE approval mark on the rating plate
   • any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any product used with inappropriate fuel mixture (fuel, oil, ratio of oil/ fuel mixture)
   • any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Accessories provided with the tool or purchased separately including but not limited to blades, saw chains, cutting lines, etc.
   • Any periodic adjustments to or maintenance cleaning of carburettors
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE

Any request or issue with the product can be addressed to your local authorised service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

DECLARATION OF CONFORMITY

Cordless secateurs

Brand: RYOBI | Model number1 | Serial number range2
We declare as the manufacturer under our sole responsibility that the product mentioned below fulfills all the relevant provisions of the following European Directives, European Regulations and harmonised standards3
Authorised to compile the technical file:4

1. RY18SCXA
2. 47564301000001 – 47564301999999
3. 2006/42/EC, 2014/30/EU, 2011/65/EU
   • EN 62841-1:2015; EN ISO 12100:2010; EN 55014-1:2017+ A11: 2020;
   • EN 55014-2:2015; EN IEC 63000:2018

• Todd Chipner
• Vice President, Quality – Asia
• Winnenden, July 2, 2021
• 4 Alexander Krug, Managing Director

Techtronic Industries GmbH

• Max-Eyth-Straße 10, 71364 Winnenden, Germany.

GB-DECLARATION OF CONFORMITY

• Manufacturer: Techtronic Industries GmbH
• Max-Eyth-Straße 10, 71364 Winnenden, Germany

We declare as the manufacturer under our sole responsibility that the product mentioned below

• Cordless secateurs
• Brand: RYOBI
• Model number: RY18SCXA
• Serial number range: 47564301000001 – 47564301999999

fulfills all the relevant provisions of the following Regulations: S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:

• BS EN 62841-1:2015; BS EN ISO 12100:2010;
• BS EN 55014-1:2017+ A11: 2020; BS EN 55014-2:2015;
• BS EN IEC 63000:2018

Todd Chipner

• Vice President, Quality – Asia
• Winnenden, July 2, 2021
• Authorised to compile the technical file:
• Alexander Krug, Managing Director

Techtronic Industries GmbH

• Max-Eyth-Straße 10, 71364 Winnenden, Germany

RYOBI is a trade mark of Ryobi Limited, and is used under license.

© 2021 Techtronic Cordless GP.

Techtronic Industries GmbH

• Max-Eyth-Straße 10,
• 71364 Winnenden, Germany

Techtronic Industries (UK) Ltd

• Fieldhouse Lane
• Marlow Bucks SL7 1HZ UK

References

• license.de
• Ryobi Tools
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>