RYOBI RID18X Cordless Brushless Performance Impact Driver User Manual

: June 12, 2024
: RYOBI

Table of Contents

IMPACT DRIVER SAFETY WARNINGS
ADDITIONAL BATTERY SAFETY WARNINGS
KNOW YOUR PRODUCT
MAINTENANCE
SYMBOLS
SYMBOLS IN THIS MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**RYOBI RID18X Cordless Brushless Performance Impact Driver User Manual

**

Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Safety, performance, and dependability have been given top priority in the design of your impact driver.

The impact driver is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.

The product is intended for fastening and removing screws and bolts.

The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference

IMPACT DRIVER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Dust created by operating the product can cause respiratory injury. Wear appropriate dust control mask with filters suitable for protecting against particles from the material being worked on.
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.
Ambient temperature range for tool during operation is between 0°C and 40°C.
Ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
Ambient temperature range for battery during use is between 0°C and 40°C.
Ambient temperature range for battery storage is between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 56.

Chuck
Direction of rotation selector
Variable speed switch trigger
Handle, insulated gripping surface
LED light
Low speed
Medium speed
High speed
“A” mode*
Mode selection button
Single bit
Single bit
Bit adaptor
Battery port
Belt clip
Belt clip screw
Operator’s manual
Battery pack
Charger

*Use the “A” mode to drive screws when better control is required. This mode starts at a lower speed and then increases to fi nish driving in the screw.
In reverse direction, this mode rotates in 6 pulses moving up to a controlled reverse speed designed to remove screws with damaged heads.

MAINTENANCE

The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.
When servicing, use only original manufacturer’s replacement parts, accessories and attachments. Use of any other parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
For greater safety and reliability, all repairs should be performed by an authorised service centre.

SYMBOLS

Safety Alert
V Volts

No-load speed
min־¹ Revolutions or reciprocation per minute

Direct current

European Conformity Mark

British Conformity Mark

Ukraine Conformity Mark

Eur Asian Conformity Mark

Please read the instructions carefully before starting the machine.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.