VISIONTRACK VT650-AI Intelligent Pedestrian Detection Camera Instruction Manual

VT650-AI Intelligent Pedestrian Detection Camera

Product Information

The VT650-AI is an intelligent pedestrian detection camera that utilizes deep learning technology to detect vulnerable road users such as pedestrians, cyclists, motorcyclists, and people on scooters. It offers real-time, high- precision detection of pedestrians and vehicles at the front, side, and rear of the vehicle. The camera can be configured to provide visual and audio alerts to warn drivers of potential risks or collisions.

This camera is designed as an essential driving aid for larger commercial vehicles, including HGVs, buses, vans, plant, and other construction equipment. It can also replace a side scan system and is approved by TFL (Transport for London) and compliant with DVS (Direct Vision Standard).

The VT650-AI offers the very latest technology to help drivers detect vulnerable road users including pedestrians, cyclists/ motorcyclists and people on scooters. The camera adopts deep learning technology, which can realise intelligent and high-precision pedestrian and vehicle detection at the front, side and rear of the vehicle in real time. Visual and audio alerts can be configured to warn drivers of potential risks or collisions.
This camera is an essential driving aid and is suitable for larger commercial vehicles such as HGVs, buses, vans, plant and other construction equipment. This all-in-one unit can also replace a side scan system and is both TFL- approved and DVS-compliant.

Key Features

• Helps protect against collisions with vulnerable road users
• Offers visible warnings through an optional monitor
• Can be connected to VisionTrack’s IoT platform for additional functionality
• 1080P full-HD camera
• Water-resistant and dustproof with an IP69K rating

Camera

| Resolution / Frame| Full HD 1920×1080 / 25 fps or 1920×1080 /30 fps
Focal Length / Viewing Angle (H)| 1.45mm/170°

Video

| Video Output| AHD (1.0Vp-p, 75Ohm)
Resolution / Frame| 1920×1080 / 25fps or 1920×1080 / 30fps
Audio| Audio Output| Warning acoustic signal output

Interface

|

Communication Interface

| USB 2.0（For external Wi-Fi module)

Power

| Input Power| DC 10~32V

Power Dissipation (12V IN)

|

320mA

Cable| Cable Length| 0.5m

Power

|

Operation Temperature

|

-20~70°C

Storage Temp| -40~85°C
Protection| Waterproof Rating| IP69K

Appearance

| Dimensions (mm)| 139.7 x 63.2 x 53.5mm
Weight (g)| 386g
Casing Colour| Black

Specifications

Volume| Set the alarm volume level in range 0-5. The default level is 5 (max.). Level 0 means no sound.
---|---
External Alarm Volume| Set audible and visual alarm volume. The default value is 8.
Audio Type| Switch alarm sound type. The default sounds ‘Ding’. There are 6 different tone options.
PD Model| Set the algorithm model. Person: only detect pedestrians; Person & Car: detect both vehicles and pedestrians.
PD Sensitivity| The higher, the more false detection; the lower, the more missing detection.
OSD Font Size| Close ‘Confidence’ and adjust the font size.

PD Alarm In

| Pedestrian detection trigger input. When enabled, the pedestrian detection algorithm will be enabled only when the multi-functional CAN wire or device with alarm input is connected, and the alarm in provides 12V voltage.
PD Test Mode| After turning on, when a pedestrian is detected outside a specific area, it will display within a blue box. The ‘Confidence’ of the detected pedestrian will display.
Person Rectangle| Select whether to display pedestrian rectangle after detecting pedestrians.
Zone Interval| Set the lowest pedestrian interval between each ROI area alarm, the alarm does not alarm during the interval.

Alarm Out Duration

| Set the duration of trigger line output high level after pedestrian is detected in the detection area, which is 2 seconds by default. That is, after the pedestrian is detected, the trigger line outputs a high level. When no pedestrian is detected again, the high level lasts for 2 seconds and then drops to a low level.
Alarm Out Switch| Select whether the trigger line outputs high level after the pedestrian is detected in the Red/Yellow/Green corresponding detection area.

Detection Zone Switch

| Switches control if the detection areas corresponding to Red/Yellow/Green are displayed. When you click to turn off, the detection area will not be displayed and pedestrian detection will not be performed. It takes effect immediately once it has been set.
Detection Zone Style| Fill background colour of Detection Zone and select colour of Box Line. Or select Hide to disable background colour display.
Work Speed| After the external GPS is connected, the algorithm will be activated when the driving speed is lower than the working speed.

Product Usage Instructions

To set the alarm volume level:

1. Access the volume settings on the camera.
2. Adjust the volume level within the range of 0-5. The default level is 5 (maximum).
3. A level of 0 means no sound will be emitted.

To set the audible and visual alarm volume:

1. Access the audio settings on the camera.
2. Adjust the volume level to the desired value. The default value is 8.

To switch the alarm sound type:

1. Access the audio settings on the camera.
2. Select from 6 different tone options for the alarm sound.
3. The default sound is “Ding”.

To set the algorithm model:

1. Access the camera settings.
2. Select the desired algorithm model: “Person” to detect only pedestrians, or “Person & Car” to detect both vehicles and pedestrians.
3. Note that adjusting the sensitivity level can affect the detection accuracy. Higher sensitivity may result in more false detections, while lower sensitivity may lead to more missed detections.

To adjust the OSD (On-Screen Display) font size:

1. Access the OSD settings on the camera.
2. Disable the “Confidence” option.
3. Adjust the font size to the desired value.

To enable pedestrian detection trigger input:

1. Connect the multi-functional CAN wire or a device with alarm input to the camera.
2. Enable the pedestrian detection algorithm.
3. The algorithm will only be active when the trigger input provides a 12V voltage.

To display pedestrian rectangle after detecting pedestrians:

1. Access the camera settings.
2. Select whether to display a blue box around detected pedestrians.

To set the lowest pedestrian interval between each ROI area alarm:

1. Access the camera settings.
2. Adjust the interval value to determine when the alarm should not trigger during a specific period.

To set the duration of trigger line output after pedestrian detection:

1. Access the camera settings.
2. Set the duration for the trigger line to output a high level after detecting a pedestrian in the detection area.
3. The default duration is 2 seconds.

VisionTrack Copyright © 2022 – All Rights Reserved. All manufacturers specifications are subject to change without notice. No liability will be accepted by VisionTrack for any errors or omissions in this information.

CONTACT INFORMATION

• t +44 (0) 1246 225 745
• e[email protected]
• wvisiontrack.com
• ssupport.visiontrack.com

References

• Next Generation Video Telematics Platform
• Home | Visiontrack Support
• VisionTrack | Global Provider of AI Video Telematics

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>