robern SLEDS12 Selectable Night Light Installation Guide
- June 12, 2024
- robern
Table of Contents
robern SLEDS12 Selectable Night Light
Product Information
The selectable night light accessory is designed for Vanities. It is available in several widths, including SLEDS12, SLEDS24, SLEDS30, and SLEDS36. You can choose between two color temperatures: 2700K (warm white) or 4000K (neutral white).
Product Usage Instructions
- Before starting the installation process, ensure that the vanity is not fully installed. If it is already installed, follow the instructions provided with your vanity to remove the side kit glass.
- Locate the wire management channel and peel back the label. Stick the wire management channel onto the inside wall of the vanity, approximately 1-1/2 inches from the top.
- Position the night light assembly as shown and thread the electrical connectors through the square hole on the side of the vanity.
- Refer to figure two for a cross-section view of the night light assembly. Align the assembly in position [A] and rotate it up into position [B] until it locks into place.
- Thread the electrical connectors through the rectangular hole and slide the wire into the groove in the wire management channel.
- Uncoil the wire attached to the included power supply. Use the supplied splice connector to connect the power supply wire to the LED wire of your chosen LED color temperature (2700K or 4000K).
- Plug the power supply into a wall outlet and test the night light. After inspection, continue with the vanity assembly as per the instructions provided with your vanity. Ensure that you do not pinch the night light wires when installing the side kit glass.
- If you need to remove the night light assembly, use a small flat-blade screwdriver to gently rotate the assembly from position [A] to [B] as shown.
- Note: When installing multiple night lights, a power strip can be used.
CAUTION: The mounting means provided with this luminaire has not been evaluated for reliability. If installed where failure of the mounting means could cause injury to persons or damage to property below, supplemental means of securement should be considered.
PARTS
INSTALLATION
This instruction covers installation of the selectable night light accessory
for Vanities. You have the option of selecting either 2700K (warm white) or
4000K (neutral white). While night lights are available in several widths,
installation methods remain the same.
ATTENTION: It is important that this installation be completed FIRST, before
the rest of your vanity installation is complete. If the vanity is already
installed, the side kit glass will need to be removed following the
instructions supplied with your vanity. If Vanities have been ganged three or
more wide, you may need to separate the inside vanities to gain access for
this installation.
- Locate the wire management channel and peel back the label. Adhere the wire management channel by pressing the sticky side onto the inside of the vanity wall, approx 1-1/2 inches from the top.
- Position the night light assembly as shown, and thread the electrical connectors through the square hole on the side of the vanity.
- Figure two is a cross-section of the night light and how it fits into the vanity. Align the night light assembly in position [A] and rotate it up into position [B] until it locks into place as shown.
- Thread the electrical connectors through the rectangular hole and slide the wire into the groove in the wire management channel.
- Uncoil the wire attached to the included power supply. Use the supplied splice connector to connect the power supply wire to the LED wire of your chosen LED color temperature as shown.
- Plug the power supply into the wall and test. After inspection, continue the vanity assembly per the instructions supplied with your vanity. Be sure not to pinch the night light wires when installing the side kit glass. Note: When installing multiple night lights, a power strip can be used.
- If the night light assembly needs to be removed, using a small flat blade screwdriver, gently rotate the assembly from position [A] to [B] as shown.
CAUTION: The mounting means provided with this luminaire has not been evaluated for reliability. If installed where failure of the mounting means could cause injury to persons or damage to property below, supplemental means of securement should be considered.
© 2017 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
- 800.877.2376
- www.robern.com
Part no. 209-1295 || March 31, 2022 Selectable Vanity Night Light Installation
Installation instructions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>