robern LIT Wall-Mounted Magnification Mirror Installation Guide
- June 3, 2024
- robern
Table of Contents
robern LIT Wall-Mounted Magnification Mirror
GENERAL INFORMATION
This instruction sheet contains information on how to install the Wall-Mounted
Magnification Mirror. This series comes in many variations. Please refer to
the box or product label for the specific model number.
Save these instructions for future use and reference. An improper installation
voids the warranty. Carefully inspect the product for damage. Installed
products cannot be returned.
If you experience any problems with your product, contact your dealer or
Robern directly.
Limited Warranty — One Year Term
TOOLS NEEDED
PARTS
IMPORTANT SAFETY INSTRUCTIONS
Unpack the magnification mirror. Check the box thoroughly for all hardware and
loose parts. Carefully inspect the magnification mirror for damage.
Observe all local electrical codes and building codes. Wire the mirror in
accordance with the electrical codes.
This magnification mirror is for indoor use only.
This magnification mirror is UL listed for damp locations and conforms to UL
962; certified to CAN/CSA C22.2 Canadian Electrical Code.
When using an electrical furnishing, basic precautions should always be
followed, including the following:
Read all instructions before using the wall mounted magnification mirror.
DANGER – To reduce the risk of electric shock:
- Always unplug this furnishing from the electrical outlet before cleaning or servicing.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
-
Unplug from outlet before putting on or taking off parts.
-
Close supervision is necessary when this furnishing is used by, or near children.
-
Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
-
Do not operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact a local service center for examination and repair, or contact your dealer or Robern directly.
-
Keep the cord away from heated surfaces.
-
Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
-
Never drop or insert any object into any opening.
-
Do not use outdoors.
-
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
-
To disconnect, turn all controls to the off position, then remove plug from outlet.
WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions. -
Mount furnishings at the correct height.
DANGER – RISK OF SHOCK –
DISCONNECT POWER BEFORE INSTALLATION
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system,
or an equipment grounding conductor must be run with the circuit conductors
and connected to the equipment grounding terminal or lead on the product.
See details on page 6.
ASSEMBLY
The hardwired magnification mirror comes in several design variations and must be mounted to a standard octagon or 4″ round type electrical box. The electrical box should be pre-installed in the wall in accordance with local building and electrical codes.
IMPORTANT: DISCONNECT POWER BEFORE INSTALLATION
- Remove the mounting plate by unscrewing the decorative nuts on the the magnification mirror base. Set this hardware aside in a safe place.
- Once the mounting plate is free, pass the field wiring through the center opening of the mounting plate.
- Align the supplied mounting screws with the electrical box screw locations and loosely install screws.
- Using a level, adjust the rotation of the mounting plate until it’s level.
- While holding the mounting plate level, tighten the screws (must be flat head), securing the mounting plate to the electrical box.
- Using the wire nuts provided, make all electrical connections using the electrical diagram as reference.
- Push excess wire into the electrical box and reinstall the decorative nuts removed in Step 1.
CLEANING AND CARE
NOTE: Under no circumstances should an ammonia-based cleaner be used on
magnification mirror. When cleaning the mirror surface use only a lint-free
polishing cloth for cleaning. To remove stubborn stains slightly dampen the
cloth with water or rubbing alcohol. When cleaning the metal frame, use only a
damp cloth.
NOTE : Do not use abrasive cleansers on any part of the magnification
mirror.
WARRANTY
Limited Warranty One Year Term
Robern warrants to the original purchaser that, it will, at its election
repair, replace, or make appropriate adjustment to products made by this
company shown to have significant defects in material or workmanship which are
reported to Robern in writing within one (1) year from the date of delivery.
Robern is not responsible for installation costs. The warranty is void in the
event the product is damaged in transit, or if damage or failure is caused by
abuse, misuse, abnormal usage, faulty installation, damage in an accident,
improper maintenance, or any repairs other than those authorized by Robern. At
the expiration of the one year warranty period, Robern shall be under no
further obligation under any warranty, expressed or implied, including the
implied warranty of merchantability. Robern shall not be liable for any
consequential damages arising out of or in connection with the use or
performance of its products. Some states do not allow limitations on how long
an implied warranty lasts or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may
not apply to you. Any liability against Robern under any implied warranty,
including the warranty of merchantability, is expressly limited to the terms
of this warranty. Permission to return any merchandise under this warranty
must be authorized by Robern and returned prepaid by the purchaser. Claims
under this warranty should be sent directly to your dealer.
© 2021 Robern, Inc.
All rights reserved