Bissell 2920C Powerglide Plus Lift Off Pet Upright Vacuum Instruction Manual

: June 12, 2024
: Bissell

Table of Contents

Bissell 2920C Powerglide Plus Lift Off Pet Upright Vacuum
IMPORTANT SAFETY INSTRUCTIONS WARNING
Warranty
What’s in the Box?
Assembly
Using Your Vacuum
Above Floor Cleaning
Post-Motor Filter
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bissell 2920C Powerglide Plus Lift Off Pet Upright Vacuum

IMPORTANT SAFETY INSTRUCTIONS WARNING

READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE.
Always connect to a polarized outlet (one slot is wider than the other). Unplug from the outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following:

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY

Do not leave the vacuum cleaner when it is plugged in. Unplug from the outlet when not in use and before servicing.
Do not use it outdoors or on wet surfaces.
Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
Do not use it for any purpose other than described in this user guide. Use only the manufacturer’s recommended attachments.
Do not use a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated surfaces.
Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
Do not handle the plug or vacuum cleaner with wet hands.
Do not put any objects into openings. Do not use any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce airflow.
Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
Turn all controls OFF before plugging or unplugging the vacuum cleaner.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
Do not use a vacuum cleaner in an enclosed space filled with vapors given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
Do not use without filters in place.
Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
Use only on dry, indoor surfaces.
Keep the appliance on a level surface.
Do not carry the vacuum cleaner while it is running.
Unplug before connecting or disconnecting the TurboBrush® Tool.
Plastic film can be dangerous. To avoid the danger of suffocation, keep away from children.
Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.
Turn the Power Switch OFF and disconnect the polarized plug from the electrical outlet BEFORE performing maintenance or troubleshooting checks.

SAVE THESE INSTRUCTIONS

THIS MODEL IS FOR HOUSEHOLD USE ONLY.
COMMERCIAL USE OF THIS MACHINE VOIDS THE MANUFACTURER’S WARRANTY.

THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

Warranty

3-Year limited warranty. Visit support.BISSELL.ca or call 1-800-263-2535 for complete warranty information.

What’s in the Box?

Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.

Bissell-2920C-Powerglide-Plus-Lift-Off-Pet-Upright-Vacuum-
FIG-1

Assembly

Go to support.BISSELL.ca for assembly videos.

Attach Handle to Lift-Off Pod.
Attach Lift-Off Pod to Foot.
Attach Stretch Hose to the Handle by twisting clockwise.
Attach Stretch Hose to the back of the vacuum by twisting clockwise.
Attach tools to tool holders on the vacuum.

Using Your Vacuum

For additional ways to use your vacuum’s features, check out support.BISSELL.ca.

Turn the power ON. Turn the Brush Roll ON for carpet cleaning and the light switch will illuminate. Turn the Brush Roll OFF when vacuuming hard or delicate surfaces.
Step gently on the base and pull the handle back to recline.
Note: The Brush Roll automatically shuts OFF when the vacuum is locked in an upright position. Recline to reactivate.
Use the Carpet Type Control for optimized cleaning on high-pile and low-pile carpets. The control can be moved to the middle position for medium pile carpeting.

Above Floor Cleaning

Visit support.BISSELL.ca to see all the ways you can use your vacuum tools.

Push the Lift-Off Release Button and lift up to remove the pod from the Foot.
For the most reach, use the Quick Release Extension Wand. Push the Release Button to remove. To clean without the wand, twist the circular hose cuff counter-clockwise and remove it.
Attach the desired tool.
Note: For optimal use, attach the Pet TurboEraser® Tool directly to the Hose instead of the Handle.
Use the Carry Handle to bring the Lift-Off Pod to hard to- clean places in your home.
Replace the wand back by sliding it into place until you hear a “click”. Reattach Hose to the Handle if needed.
Place the pod back onto the Foot.

WARNING Do not plug in your vacuum until you are familiar with all instructions and operating procedures.

Emptying the Dirt Tank

For additional maintenance steps, visit support.BISSELL.ca.

Press the Dirt Tank Release Button and grab the handle to pull the Dirt Tank away from the vacuum.
Hold the Dirt Tank over a trash bin and press the Empty Button. Once emptied, snap the bottom back into place.
Return the Dirt Tank to the vacuum by securing the bottom in place first and then pushing back until you hear a “click”.

Cleaning the Inner Cyclone Separator

We have additional maintenance videos for your machine on support.BISSELL.ca.

Hold the Dirt Tank over a trash container. Press the bottom release button to empty.
Twist the separator counter-clockwise and pull down to remove.
Tap the separator against the inside of the trash container and rinse under warm water, if necessary. Be sure to let it dry completely before placing back in Dirt Tank.

WARNING To reduce the risk of electrical shock:

Turn Power Switch OFF and disconnect the polarized plug from the electrical outlet before performing maintenance or troubleshooting checks.
Before using your vacuum, make sure that the Dirt Tank is in the locked position and that all filters, both Pre- and Post-Filters, are in place. DO NOT operate your vacuum without these filters.

Cleaning and Replacing the Filters

Visit BISSELL.ca to find replacement filters.

Pre-Motor Filter

Press the Dirt Tank Release Button and pull away from vacuum.
Open the tank lid by lifting up.
Remove Pre-Motor Filters from top of Dirt Tank lid by pulling out.
Clean with mild detergent, rinse and squeeze all excess water. Allow filters to dry completely before reinserting.
Return Pre-Motor Filters to the top of the Dirt Tank. Put the thin flat filter with the white tab in first, then put the thick foam filter in.
You should hear a click when tank lid is closed securely.

Post-Motor Filter

For optimal performance, replace the filter every 6 months.

Press down on tab to remove Post-Motor Filter cover and pull away from vacuum.
Press tab on right side of filter and pull out to remove from vacuum. Remove debris from filter by tapping on the side of a trash container. This pleated filter may NOT be washed.
When reassembling, be sure to lock the filter back into place by aligning one side of the filter first, then clicking the other side into place.

WARNING To reduce the risk of electrical shock:

Turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.
Do not operate vacuum with damp or wet filters. Allow components to dry before reassembling the Dirt Tank.
Do not use without filters in place.

Protecting the Vacuum’s Motor

For more assistance with your vacuum’s motor protection, visit support.BISSELL.ca.

There is an internal thermal protector in your vacuum that protects it from overheating. It controls the main vacuum motor only, not the brush motor. When it activates, the main motor will stop.
The front lights and Brush Roll will stay on but there won’t be any suction. If this happens, follow these steps:

Turn vacuum OFF and unplug from electrical outlet.
Check for the source of overheating problem (full Dirt Tank, dirty filters or a clog) and fix by following the steps in the “Vacuum won’t pick up dirt” troubleshooting section.
When the motor cools for approximately 30 minutes, the thermal protector automatically resets and cleaning may continue. If the vacuum will not turn ON or the thermal protector continues to activate contact Consumer Care.

Troubleshooting

Below are some of the issues you may run into. If you don’t see the issue you’re experiencing below, visit support.BISSELL.ca.

Problem	Possible Cause	Remedies
Vacuum is Hard to Push or Pull

Suction needs adjustment.

| Adjust using the Suction Control feature on the Handle. See page 4.

Vacuum Won’t Pick Up Dirt

|

There is a clog in the vacuum.

| Remove main hose, run broomstick through to clear.
Remove bottom brush cover and clear debris from brush, belt and foot area.
Remove lower hose and run broomstick through to clear any clogs.

Filters are dirty.

| Remove and rinse Pre-Motor Filters. Allow enough time for them to dry completely before reinserting. Remove and dust off Post-Motor Filter. See page 6.
Incorrect Suction Control settings.| Adjust using the Suction Control feature. See page 4.

Brush Roll Doesn’t Rotate

| Brush Roll Switch is OFF.| Make sure Brush Roll Switch is ON.
Vacuum is locked in upright position.| Recline vacuum and turn the Brush Roll Switch ON.
Brush Roll has lodged debris or other entanglements, keeping the brush from rotating.| Remove bottom brush cover and clear debris from brush, belt and foot area. To reset brush motor, machine should be unplugged before turning ON.
Loud Noise| Suction relief valve was activated.| Clear any clogs from the upper and lower hose and brush area. Also clean all filters.

WARNING To reduce the risk of electrical shock, turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

We’re Waggin’ Our Tails!

BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL product, you help save pets, too. We’re proud to design products that help make pet messes, odours and pet homelessness disappear.
Visit BISSELLsavespets.ca to learn more.

But wait, there’s more!