HANOVER HHARPERBRCHR-1WS Harper 1 Light Wall Sconce Single Instruction Manual
- June 12, 2024
- HANOVER
Table of Contents
Assembly & Care Guide
HHARPERBRCHR-1WS Harper 1 Light Wall Sconce Single
The model number of your lighting is printed on the side of your carton.
Always use this number to identify your lighting.
Thank you for your purchase of this quality lighting. With proper use and
care, your lighting will provide you with years of use. Please follow the
instructions on how to install your lighting. If you should have any problems
with your lighting DO NOT return it to the place of purchase. Please call our
toll free number: 877-397-5144 and a
customer service representative will assist you.
Please read all instructions completely before installing your lighting.
NOTE: It is recommended to contact a licensed electrical contractor for
hardwire installation.
WARNING: To reduce the risk of fire, electric shock, or personal injury:
- Turn off /unplug lamp and allow to cool before replacing bulb.
- Do not touch bulb when fixture is turned on.
- Do not look directly at lighted bulb.
- Keep materials that burn easily away from lighted bulb.
CLEANING:
Use only soft cloth to dust and clean fixture. Never use chemicals or abrasive
cleaners as it may damage finish.
Installation Instruction
Item No: HHARPER-1WS & HWALLIS-1WS
WARNING: To avoid risk of electrical shock, be sure to shut off power
while installing or servicing this fixture.
NOTE: We advise calling a qualified electrician when making the wire
connections to the junction box.
-
Carefully unpack your new fixture and lay out all the parts on a clean surface.
-
Thread the 2 mounting screws through the mounting screw holes from the back of the mounting bracket.
-
Attach mounting bracket to the outlet box using 2 box screws. The side of the mounting bracket marked “GND” must face out.
-
Follow the wiring instruction carefully as detailed below.
-
Attach the fixture main body onto the outlet box by protruding 2 mounting screws through the mounting screw holes on the fixture cover plate (A), then tighten with 2 ball nuts (B).
-
Assembly the shade (C) onto the socket sleeve (D).
-
Install the bulb into the socket.
BULB(S) NOT INCLUDED. DO NOT EXCEED THE MAXIMUM WATTAGE RATING. -
Installation is now complete. Turn on power.
Note: 120V/60W
CONNECT THE ELECTRICAL WIRES AS FOLLOWS
- Connect the black wire from the fixture to the black (HOT) house wire with wire connector.
- Connect the white wire from the fixture to the white (NEUTRAL) house wire with wire connector.
- Connect the ground wire to the house ground wire (GREEN OR BARE COPPER). Or attach the bare copper fixture wire to the green ground screw on the cross bar.
- Tuck the wire connections neatly into the junction box.
1-Year Limited Warranty
“Limited” Warranty Program
For a period of one (1) year after purchase, Hanover Products (“Manufacturer”)
will either repair or replace defective components in accordance with this
Limited Warranty.
Sales and use taxes, plus shipping and handling charges are the responsibility
of the consumer.
This warranty is between Manufacturer and the original purchaser and is valid
only when accompanied by the original purchaser’s sales receipt showing
original date of purchase and location of purchase. Replacements under this
warranty revert back to the date of original purchase for future warranty.
Manufacturer or its authorized dealer can accept or reject warranty claims
based on its findings. This warranty applies in normal residential use only,
where an issue with the product is due to a defect in material or workmanship.
Manufacturer can make substitutions as required of materials, components, and
sub-components of comparable value and utility. This warranty is limited to
product repair or replacement (to be determined solely by Manufacturer).
Warranty return is limited to only the single affected component.
This warranty covers only manufacturing defects and does not cover normal wear
and tear, abuse or misuse, including: water damage, chemical damage, exposure
to extreme heat or cold or abrasion. This warranty is invalid if the product
is not used for intended
purpose. Manufacturer disclaims liability for any aspect of installation and
any inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not
limited to the following:
- Components subjected to abuse, including abuse intended to simulate failure.
- Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, breaks, etc.).
- Any part which merely exhibits normal wear yet functions essentially as new.
To make a claim, send a copy of the original sales receipt along with a brief
description of the problem to the email address below. Please include your
email address and daytime telephone or cell phone #. All items will be charged
actual freight costs plus $15 for handling. Repairs or replacement will be
made at the Manufacturer’s option.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER
NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR
IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS
LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF
ANY PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS
AS STATED IN THIS WARRANTY. NEITHER AF LIGHTING, THE PRODUCT MANUFACTURER NOR
ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE
ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER THAN THE WARRANTY DESCRIBED
HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Contact Warranty Services at:
1-877-397-5144 or
contactus@hanover-products.com
12/1/2021