HANOVER HHANNAHCLR-3WS Hannah 3 Light Wall Sconce Instruction Manual
- June 12, 2024
- HANOVER
Table of Contents
Assembly & Care Guide
HHANNAHCLR-3WS Hannah 3 Light Wall Sconce
The model number of your lighting is printed on the side of your carton.
Always use this number to identify your lighting.
Thank you for your purchase of this quality lighting. With proper use and
care, your lighting will provide you with years of use. Please follow the
instructions on how to install your lighting. If you should have any problems
with your lighting DO NOT return it to the place of purchase. Please call our
toll free number: 877-397-5144 and a
customer service representative will assist you.
Please read all instructions completely before installing your lighting.
NOTE: It is recommended to contact a licensed electrical contractor for
hardwire installation.
WARNING: To reduce the risk of fire, electric shock, or personal injury:
- Turn off /unplug lamp and allow to cool before replacing bulb.
- Do not touch bulb when fixture is turned on.
- Do not look directly at lighted bulb.
- Keep materials that burn easily away from lighted bulb.
CLEANING:
Use only soft cloth to dust and clean fixture. Never use chemicals or abrasive
cleaners as it may damage finish.
Installation Instruction
ltem No: HHANNAHCLR-3WS HHANNAHPNK-3WS
FIXED FIXTURE INSTALLATION INSTRUCTIONS
NOTE: We advise contacting a qualified electrician for installation.
WARNING: SHUT OFF THE POWE PPLY AT FUSE OR CIRCUIT BREAKER BOX.
MOUNTING THE FIXTURE
- Shut off the power supply at the fuse box or circuit breaker box. Remove the old fixture, including the universal mounting plate.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation
- The bag includes acrylic bead strings as follows: A (17pcs), B (1pc) and C (1pc), as shown on the right
- Follow wire instructions carefully (see fig.1)
- Use hole plug (K) to cover wire hole in the backplate (C).
- Thread 2 mounting screws through the mounting screw holes from the back of the universal mounting plate
- Attach universal mounting plate to the outlet box using 2 outlet box screws. The side of the universal mounting plate marked “GND” must face out
- Follow the ground wiring instructions carefully. (See Fig.2)
- Please adjust the distance of the arms to a proper position.
- Attach the fixture body (H) onto the outlet box, install the screws (G) through 2 holes of the body (H) and tighten with 2 screws (G) into the mounting plate.
- Hook acrylic bead string (B) on the ring of each arm
- Hook acrylic bead string (C) on the disk (F) of under arm.
- Hook acrylic bead string (A) on the disk (F) and ring of each arm.
- Insert the socket sleeve on the socket (E). Install the light bulb (not included) into the socket (E).
DO NOT EXCEED THE MAXMUM WATTAGE RATING!
CONNECTING THE WIRE (See fig.2)
- Take the black wire from the ceiling outlet box and the smooth wire leg from the fixture and twist bare ends together. Twist wire connector onto end of wire until snug
- Repeat same process with white junction box wire and ribbed wire leg of fixture wire. NOTE: Twist wire together in the same direction, then twist the wire connector onto wire.
- If your outlet box has a grounding wire (Green or bare copper). Attach this wire and the bare copper wire from the fixture together as step 1. If outlet box has no ground wire attach the bare copper fixture wire to the green ground screw on the cross bar.
- Tuck these wires connectors neatly into the ceiling outlet box and raise the collar ring (L) and thread onto collar loop (J) protruding through canopy.
PORTABLE FIXTURE INSTALLATION INSTRUCTIONS
NOTE: We advise contacting a qualified electrician for installation.
WARNING: SHUT OFF THE POWER SUPPLY AT FUSE OR CIRCUIT BREAKER BOX.
MOUNTING THE FIXTURE
- Shut off the power supply at the fuse box or circuit breaker box. Remove the old fixture, including the universal mounting plate.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation
- The bag includes acrylic bead strings as follows. A (17pcs), B (1pc), and C (1pc), as shown on the right.
- Thread 2 mounting screws through the mounting screw holes from the back of the universal mounting plate.
- Attach universal mounting plate to the outlet box using 2 outlet box screws. The side of the universal mounting plate marked “GND” must face out
- Follow the ground wiring instructions carefully. (See Fig.2)
- Please adjust the distance of the arms to a proper position
- Attach the fixture body (H) onto the outlet box, install the screws (G) through 2 holes of the body (H) and tighten with 2 screws (G) into the mounting plate
- Hook acrylic bead string (B) on the ring of each arm.
- Hook acrylic bead string (C) on the disk (F) of under arm.
- Hook acrylic bead string (A) on the disk (F) and ring of each arm
- Insert the socket sleeve on the socket (E) and install the light bulb (not included) into the socket (E).
DO NOT EXCEED THE MAXMUM WATTAGE RATING!
WIRING (See fig.2)
- Connect the electrical wires as follows. If your outlet box has a ground wire (Green or Bare Copper) connect fixture’s ground wire fo it. Otherwise attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
1-Year Limited Warranty
For a period of one (1) year after purchase, Hanover Products (“Manufacturer”)
will either repair or replace defective components in accordance with this
Limited Warranty.
Sales and use taxes, plus shipping and handling charges are the responsibility
of the consumer.
This warranty is between Manufacturer and the original purchaser and is valid
only when accompanied by the original purchaser’s sales receipt showing
original date of purchase and location of purchase. Replacements under this
warranty revert back to the date of original purchase for future warranty.
Manufacturer or its authorized dealer can accept or reject warranty claims
based on its findings. This warranty applies in normal residential use only,
where an issue with the product is due to a defect in material or workmanship.
Manufacturer can make substitutions as required of materials, components, and
sub-components of comparable value and utility. This warranty is limited to
product repair or replacement (to be determined solely by Manufacturer).
Warranty return is limited to only the single affected component.
This warranty covers only manufacturing defects and does not cover normal wear
and tear, abuse or misuse, including: water damage, chemical damage, exposure
to extreme heat or cold or abrasion. This warranty is invalid if the product
is not used for intended
purpose. Manufacturer disclaims liability for any aspect of installation and
any inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not
limited to the following:
- Components subjected to abuse, including abuse intended to simulate failure.
- Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, breaks, etc.).
- Any part which merely exhibits normal wear yet functions essentially as new.
To make a claim, send a copy of the original sales receipt along with a brief
description of the problem to the email address below.
Please include your email address and daytime telephone or cell phone #. All
items will be charged actual freight costs plus $15 for handling. Repairs or
replacement will be made at the Manufacturer’s option.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER
NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR
IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS
LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF
ANY PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS
AS STATED IN THIS WARRANTY. NEITHER AF LIGHTING, THE PRODUCT MANUFACTURER NOR
ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE
ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER THAN THE WARRANTY DESCRIBED
HEREIN, AND ALL OTHER ‘WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Contact Warranty Services at:
1-877-397-5144 or contactus@hanover-
products.com
12/1/2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>