HILTI SCO 6-22 Cordless Multi Tools User Manual

HILTI SCO 6-22 Cordless Multi Tools

Product Information

• Product Name: SCO 6-22
• Language Options: Deutsch, English, Italiano, Nederlands, Dansk, Svenska, Suomi, Polski
• Type: Electric power tool
• Model Number: SCO 6-22 02
• Serial Number: Located on the type plate

Information about the documentation

About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.

Explanation of symbols

1. Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:

   • DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
   • WARNING! Draws attention to a potential threat of danger that can lead to serious injury or fatality.
   • CAUTION! Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.

2. Symbols in the operating instructions
   The following symbols are used in these operating instructions:

3. Symbols in illustrations
   The following symbols are used in illustrations:

Product-dependent symbols

1. Symbols on the product
   The following symbols can be used on the product:

Product information
products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are printed on the rating plate.

• Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Declaration of conformity
The manufacturer declares, on his sole responsibility, that the product described here complies with the applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

Safety

General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety instructions for routers

• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by your hand or against the body leaves it unstable and may lead to loss of control.

Battery use and care

• Comply with the following safety instructions for the safe handling and use of Li-ion batteries.
• Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
• Use only batteries that are in perfect working order.
• Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
• Do not under any circumstances modify or tamper with batteries!
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
• Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
• Never use recycled or repaired batteries.
• Never use the battery or a battery-operated power tool as a striking tool.
• Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
• Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
• Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
• Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
• Do not use or store the battery in explosive environments.
• If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled “Instructions on safety and use for Hilti Li-ion batteries”.

Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.

Additional safety instructions

• Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed accessories are secure.
• Do not attach a belt hook to this product.
• Use the product and accessories only when they are in perfect working order.
• Never tamper with or modify the product or accessories in any way.
• Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the product could give you an electric shock or cause an explosion if you accidentally damage an electric cable or a gas or water pipe.
• Before starting work, check the hazard class of the dust that will be produced when working.
• Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone and other products containing silicates; certain types of wood, such as oak, beech and chemically treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and bystanders by means of the hazard classification of the materials to be worked. Implement the necessary measures to restrict exposure to a safe level, for example by the use of a dust collection system or by the wearing of suitable respiratory protection. The general measures for reducing exposure include:
  • working in an area that is well-ventilated,
  • avoidance of prolonged contact with dust,
  • directing dust away from the face and body,
  • wearing protective clothing and washing exposed areas of the skin with water and soap.
• Wear eye protection, a hard hat and ear protection and suitable respiratory protection while the product is in use.
• Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in cuts and burns.
• Make sure that the accessory tools used have a mounting system compatible with the product and that they are correctly engaged in the chuck.
• Before switching on the product, check that the collet is fitted and that the clamping nut is tightened.
• Use both hands to hold the product firmly by the insulated gripping surfaces. Keep the gripping surfaces dry and clean.
• Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!
• Do not touch rotating parts – risk of injury!
• Do not look directly into the light source (LED) of the product and do not aim the beam at other persons’ faces. Risk of dazzling or eye damage.
• Never touch the clamping nut or collet when the accessory tool gets stuck and stalls.
• Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands and wrists.
• Immediately switch off the power tool if the accessory tool jams. The product might twist off-line.
• Wait until the power tool stops completely before you lay it down.

Description

Product Overview

1. Vacuum cleaner hose connector
2. LED lights
3. Depth gauge
4. Securing screw
5. On/off switch
6. Switch-on interlock
7. Tool bit
8. Collet
9. Clamping nut
10. Insulated grip surface
11. Spindle lock button
12. Insulated grip surface
13. Air vents
14. Battery
15. Release button, battery
16. Battery status indicator
17. Installation opening for accessories

Intended use
The product described is a hand-held cordless cut-out tool. It is designed for making cut-outs in drywall board, gypsum fiber board, composite materials and wood or wood-like materials. The product comes with a removable vacuum cleaner hose connector for common vacuum cleaner hoses. The connector fits on to the product, enabling it to be connected to a vacuum cleaner.

• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in the table at the end of these operating instructions for this product.
• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.

Status indicators of the Liion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery’s state of health.

Indicators for state of charge and fault messages
WARNING Risk of injury by a falling battery!

• If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure.

Short-press the release button of the battery to get whichever of the following status indications is applicable at the time. State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.

Recharge the battery.
If the LED again starts quick-flashing after the bat- tery has been charged, consult Hilti Service.
One (1) LED quick-flashes yellow| The Li-ion battery or the product in which it is in- serted is overloaded, too hot or too cold, or experi- encing some other fault.
Bring the product and the battery to the recom- mended working temperature and do not overload the product when it is in use. If the message persists, consult Hilti Service.
One (1) LED shows yellow| The Li-ion battery and the product in which it is inserted are not compatible. Consult Hilti Service.
One (1) LED quick-flashes red| The Li-ion battery is locked and cannot be used. Consult Hilti Service.

Indicators showing the battery’s state of health
To check the battery’s state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example battery dropped or pierced, external heat damage, etc.

The battery can remain in use.
All LEDs show in sequence, followed by one (1) LED quick-flashing yellow.| The check to ascertain the battery’s state of health did not complete. Repeat the procedure, or consult Hilti Service.
All LEDs show in sequence, followed by one (1) LED showing constantly red.| If a connected product can still be used, the re- maining battery capacity is below 50 %.

If a connected product can no longer be used, the battery has reached the end of its useful life and has to be replaced. Consult Hilti Service.

Safety devices
This product has a motor protection system. It monitors current consumption and motor temperature and prevents the product from overheating. If the motor is overloaded through application of excessive working pressure, the product’s performance drops noticeably or it might stall completely. If the power tool stalls or slows significantly due to overloading, release the pressure applied to the product and then allow it to run under no load for approx. 30 seconds.

Items supplied
Cut-out tool, depth gauge, three collets (3.2 mm (1/8″), 4 mm (5/32″), 6.4 mm (1/4″)), clamping nut, vacuum cleaner hose connector, hex wrench, operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group

Accessory tools
The following accessory tools can be used with the cut-out tool:

Drywall

• Guidepoint bit (3.2 mm (1/8″))
• Standard bit (3.2 mm (1/8″))
• Universal guide point bit (4 mm (5/32″))
• Window/door guide point bit (6.4 mm (1/4″))

Metal

• Metal bit (4 mm (5/32″))

Technical data

Cut-out tool

Battery

Noise information and vibration values in accordance with EN 60745
The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to compare one power tool with another. They can also be used for a preliminary assessment of exposure. The data given represents the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.

Noise information

Total vibration

Preparations at the workplace

WARNING Risk of injury by inadvertent starting!

• Before inserting the battery, make sure that the product is switched off.
• Remove the battery before making any adjustments to the power tool or before changing accessories. Observe the safety instructions and warnings in this documentation and on the product.

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery.

Inserting the battery
WARNING -Risk of injury by short circuit or falling battery!

• Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
• Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.

Removing the battery

1. Press the battery release button.
2. Remove the battery from the product.

Changing the collet

1. Press the spindle lockbutton and hold it in this position.
2. Use a hex. wrench to release and remove the clamping nut.
3. Remove the collet currently installed.
4. Insert the collet you want to use.
5. Screw on and tighten the clamping nut and then release the spindle lockbutton.

Installing the vacuum cleaner hose connector

1. Remove the tool bit.
2. Install the hose connector on the product and set the connector to the desired position.
3. Engage the retaining lugs.

Installing the depth gauge
WARNING- Risk of injury! A damaged depth gauge may present a risk of inadvertent contact with the accessory tool.

• Do not use the power tool if the depth gauge is defective.

1. Hold the depth gauge in position on the product and tighten the securing screw.
2. Slacken the securing screw to adjust the depth gauge.
3. Slide the depth gauge to the desired position and re-tighten the securing screw.
4. Before starting, make sure that the space behind the workpiece is enough to keep the accessory tool from contacting a hard object.

Installing the tool bit
CAUTION -Risk of damage. The collet can break if tightened when no accessory tool is fitted.

• Never tighten the collet when no accessory tool is fitted.

1. Clean the connection end of the tool bit.
2. Check that the collet has been fitted.
3. Press the spindle lockbutton and hold it in this position.
4. Insert the tool bit into the collet and tighten the clamping nut with the hex wrench.
5. Release the spindle lockbutton.
6. Check that the tool bit is held securely.

Removing tool bit
CAUTION- Risk of injury! The accessory tool may be hot and/or have sharp edges.

• Wear protective gloves when changing the accessory tool.
• Never lay down a hot accessory tool on a flammable surface.

1. Press the spindle lockbutton and hold it in this position.
2. Use the hex. wrench to release the clamping nut.
   • The collet is slack.
3. Remove the tool bit.

Fall arrest
WARNING- Risk of injury by falling tool and/or accessory!

• Use only the Hilti tool tether recommended for your product.
• Prior to each use, always check the attachment point of the tool tether for possible damage.

Comply with the national regulations for working at heights.
As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether #2261970.

• Secure the retaining strap to the installation openings for accessories. Check that it holds securely.
• Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a load-bearing structure. Check that both carabiners hold securely.

Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.

Operation

Observe the safety instructions and warnings in this documentation and on the product.

Switching on
The on / off switch with switch-on interlock gives you full control of the switch function and avoids unintentional starting.

1. Push the switch-on interlock forward.
   • The on/off switch is unlocked.
2. Press the on/off switch as far as it will go.
   • The power tool’s motor runs at no-load speed.

Holding the product correctly

1. Use clamps or some other practical means to secure the workpiece and keep it in a stable position.
2. Use both hands to hold the product firmly when working.
   • The product can become unstable if you attempt to hold it with only one hand or pressed against a part of the body and this can result in loss of control.

Operation

1. Hold the product firmly without the tool bit contacting the working surface.
2. Switch on.
3. Guide the accessory tool straight into the material in which the cut-out is to be made, until the depth gauge is in contact with the working surface.
4. Applying steady pressure, advance the accessory tool.

Switching off

• Release the on/off switch.
• The switch-on interlock jumps automatically into the locked position.

Care and maintenance

WARNING – Risk of injury with battery inserted!

•  Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.
• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts. Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group

Transport and storage of cordless tools and batteries

Transport
CAUTION Accidental starting during transport!

• Always transport your products with the batteries removed!
• Remove the battery/batteries.
• Never transport batteries loose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
• Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
• Prior to each use and before and after prolonged transport, check the product and the batteries for damage.

Storage
WARNING Accidental damage caused by defective or leaking batteries!

• Always store your products with the batteries removed!
• Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
• Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
• Never leave batteries in direct sunlight, on sources of heat, or behind glass.
• Store the product and batteries where they cannot be accessed by children or unauthorized persons.
• Prior to each use and before and after prolonged storage, check the product and the batteries for damage.

Troubleshooting

If a problem occurs, always observe the charge status and fault indicator of the battery. See the section headed Status indicators of the Liion battery. If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service.

▶ Replace the battery.
The battery doesn’t engage with an audible click.| The retaining lug on the battery is dirty.| ▶ Clean the retaining lug and re-insert the battery.
LEDs of the battery show nothing| Battery defective| ▶ Contact Hilti Service.
Product or battery gets very hot| Electrical fault| ▶ Switch the product off immedi- ately, remove the battery, keep it under observation, allow it to cool down and contact Hilti Service.
The motor has no braking effect.| Battery is discharged.| ▶ Change the battery and charge the empty battery.
Product is momentarily overloaded.| ▶ Release the on/off switch and then press it again.

Disposal

WARNING
Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

• DO NOT send batteries through the mail!
• Cover the terminals with a non-conductive material (such as electrical tape) to prevent short-circuiting.
• Dispose of your battery out of the reach of children.
• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

Do not dispose of power tools, electronic equipment or batteries as household waste!

Manufacturer’s warranty

• Please contact your local Hilti representative if you have questions about the warranty conditions.

Further information
For more information on operation, technology, environment and recycling, follow this link: qr.hilti.com/manual/?id=2264441
This link is also to be found at the end of the documentation, in the form of a QR code.

Hilti Corporation
LI-9494 Schaan
Tel.: +423 234 21 11
Fax: +423 234 29 65
www.hilti.group

References

• HILTI Country selector
• Главная страница - Hilti Россия

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>