gutta 9219119 Rectangular Canopy with Side Panel Instruction Manual

gutta 9219119 Rectangular Canopy with Side Panel

Product Information

• Product Name: Rechteckvordach BS Plus 160/200 mit Seitenteil
• Product Number: 9219119
• LED-Lichttechni Energieeffizienz Umweltfreundlich

Features

• Rectangular canopy with side panel
• LED lighting technology
• Energy efficient
• Environmentally friendly

Product Usage Instructions

Mounting Instructions for BS Plus 160 / 200

1. Mounting the wall bracket:
   • Attach the wall bracket to the wall.
   • Use 6 screws for BS 160 and 9 screws for BS 200.
2. Detach the LED panel and pull the power cable through the canopy.
3. Fastening at the top:
   • Attach the joint sealing tape to the angle.
   • Drill holes with a 3.5mm drill bit.
   • Insert screws as shown.
   • Use 8 screws for BS 160 and 12 screws for BS 200.
4. Fastening from below:
   • Use 2 screws for BS 160 and 4 screws for BS 200.
5. Power connection for LED panel.
6. Mounting the side panel:
   • Place the side panel on the brackets.
   • Slide the side panel up to the canopy.
7. Fastening:
   • Use 6 screws for BS 160 and 6 screws for BS 200.
8. Apply a silicone joint between the wall and the canopy.
   Note: The product also includes Hohlkammerplatten Twinwall sheets, but no specific instructions are provided in the given text-extract.

Important Reccommendations!

• Prior to assembly please study the assembly in-structions in detail and check the consignment for possible faulty parts or damage during transpor-tation. No liability will be assumed for damage to products already assembled.
• Please check that type, dimensions and colour are correct before assembly.
• Custom-made products cannot be exchanged.
• The canopy may only be used for the intended purpose, failing which no claims for product liabili-ty can be accepted!
• Clean the canopy every 3 months and only use a re-commended cleaning product (no scrubbing agents or solvents). If necessary, the lacquered parts can also be treated with with car polish.
• The water drains should be cleaned regularly (in order to avoid damage caused by accumulated wa-ter).
• In each case, the canopy fastenings must be sui-table for the construction of the wall in question. Secure attachment must be ensured.
• Accumulated snow and ice should be removed from the canopy.
• Caution – Danger of accident! The canopy is not load bearing; do not climb or place your weight on the canopy.
• Recommendation: Assembly should be carried out by two persons. You must also seal the canopy using standard commercial silicone.
• The electrical installation must be carried out or removed by a qualified electrician.
• No guarantee claims can be accepted for parts subject to wear and tear after the statutory guaran-tee period has expired.
• We can also supply separate accessories for this canopy. Please ask your local dealer for details.
• The design is subject change.

ACCESORIES

TOOLS REQUIRED

Mounting dimensions

Mounting instructions

1. Mounting the wall bracket
2. Measure distances, align with a water level, mark drill holes (use wall holder as template)
3. Drill the holes with a Ø 12 mm drill bit
4.  Insert dowels into the wall and then loosely fit the wall brackets with 3 screws and washers each.
5. Align the wall brackets with a spirit level and then tighten the screws.

2. Preparing the power connection for the LED panel
   Detach the LED panel and pull the power cable through the canopy.

3. Fastening at the top
   • Attach the joint sealing tape to the angle. Drill the holes with a 3.5mm drill bit.
   • Insert the screws as shown.

4. Fastening from below
5. Pre-drill the holes with a 3.5 mm drill bit.
6. Insert the screws as indicated.

3. On the side where the side panel will be mounted, please use the countersunk screws (2x).

5. Power connection for LED panel
   Connect the LED panel to the power cable and reattach it to the canopy.

Mounting dimensions, side panel

Mounting instructions

1. Mount wall bracket

2. Measure distances, align with a water level, mark drill holes (use wall holder as template)

3. Drill the holes with a Ø 12 mm drill bit

4. Insert dowels into the wall, and then loosely fit the wall brackets with 2 screws and washers each.

5. Align the wall brackets with a spirit level and then tighten the screws.

6. Assembly

7. Place the side panel on the brackets.

8. Slide the side panel upto the canopy.

3. Fasting

4. Pre-drill the holes with a 3.5 mm drill bit.

5. Insert the screws as indicated.

6. Fastening

7. Pre-drill the holes with a 3.5 mm drill bit.

8. Insert the screws as indicated.

5. Silicone joint
   Place a silicone joint between wall and canopy.

Overview of product range

ABOUT COMPANY

• Gutta Werke GmbH
  • Bau- und Heimwerkerprodukte
  • Bahnhofstraße 51-57
  • D-77746 Schutterwald
  • Telefon 0781 6090
  • Telefax 0781 6093200
  • info@gutta.com
• Scobalitwerk Wagner GmbH
  • Zürnkamp 27
  • D-21217 Seevetal-Meckelfeld
  • Telefon 040 2190210
  • Telefax 040 70011446
  • seevetal@scobalit.de
• Scobalitwerk Wagner GmbH
  • Fichtenstraße 18
  • D-56584 Anhausen
  • Telefon 02639 962570
  • Telefax 02639 962571
  • anhausen@scobalit.de
• Scobalitwerk Wagner GmbH
  • Hermann-Ilgen-Straße 7
  • D-04808 Wurzen
  • Telefon 03425 814708
  • Telefax 03425 814709
  • wurzen@scobalit.de
• Scobalitwerk Wagner GmbH
  • Industriepark 3
  • D-97273 Kürnach
  • Telefon 09367 98440
  • Telefax 09367 984429
  • kuernach@scobalit.de
• Scobalitwerk Wagner GmbH
  • Bahnhofstraße 51-57
  • D-77746 Schutterwald
  • Telefon 0781-9907900
  • Telefax 0781-6093207
  • offenburg@scobalit.de

References

• Home | Gutta Werke
• Der "All in one" Partner für den Baustoffhandel - Scobalit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>