LUMENA Lights AIR400-12P Airlite Stream Path Light Instructions
- June 12, 2024
- LUMENA Lights
Table of Contents
LUMENA Lights AIR400-12P Airlite Stream Path Light
Product Information
The Airlite/Airlite Stream Path Light 12v is a product offered by Lumena Lights Ltd. It is available in different models: AIR400-12P, AIR600-12P, AIR400-PC-12P, AIR600-PC-12P, AIR400S-12P, AIR600S-12P, AIR400S-PC-12P, and AIR600S-PC-12P. The product has an IP65 rating, indicating its resistance to dust and water. It comes in two different heights: 400mm or 600mm. The light features a photocell sensor that enables it to automatically turn on at dusk and off at dawn.
The product is covered by a 3-year guarantee, and additional details can be found on the manufacturer’s website. Lumena Lights Ltd is registered as Producer Registration Number WEE/KC3440XY. The company is located at Centre 33 Long March Daventry Northants NN11 4NR. They can be contacted via phone at +44 1327 871161, fax at 0800 066 4410, or email at sales@lumenalights.com. For a full range of products and more information, visit their website at www.lumenalights.com.
Product Usage Instructions
Installation:
- Seal and screw on the head of the light securely.
- When securing the base, avoid overtightening to prevent fracture. Do not use high-power electric socket tools.
- Use the supplied Male 2 Pin Plug & Play Adaptor to connect the light.
- If needed, use the Female 2-Pin Plug & Play Adaptor for additional connections.
Cleaning:
Occasional cleaning and care is recommended for the product. For specific
instructions on how to clean different materials, please refer to the
manufacturer’s website at www.lumenalights.com.
For a full VERSA Plug & Play range and more information, please visit their website at www.lumenalights.com.
WARNINGS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE COMMENCING ANY WORK.
- This is a Class 3 product (Low Voltage) – no earth required.
- 12V TRANSFORMER MAY BE REQUIRED – sold separately
- This unit must be fitted by a competent person – if in doubt consult a qualified electrician.
- Install in accordance with IEE wiring regulations and current Building Regulations.
- To prevent electrocution, switch off mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
- This light fitting should be connected to a circuit with a 30Ma RCD fitted.
- If replacing an existing fitting, make a careful note of the connections.
- When changing the bulb, always switch off at the mains & allow the bulb to cool before handling – LAMP WILL GET HOT WHEN IN USE.
- All connections should be made as watertight as possible to avoid electrical shortage.
- Always use the correct type & wattage of bulb. Never exceed the wattage stated.
- The unit may get warm whilst on for a period of time.
- The head of the product is heavy (up to 3kg) – please handle with care
INSTALLATION
- A length of 12v 2 core rubber cable is supplied with a VERSA 2 pin male plug (H05RN-F – may vary).
- Push the plug firmly into the female adaptor of the Transformer or splitter.
- Screw the attached threaded cap to the female adaptor to create a secure connection.
- If a splitter is used, ensure a waterproof cap is used to cover any unused terminals.
- Unscrew the head carefully and install the MR16 bulb into the bulb holder via the guide clip (push).
- Carefully place the rubber seal between the body and head to ensure a waterproof seal and screw on the head securely.
IMPORTANT:
When securing the base, do not overtighten as this could lead to fracture. Do
not use high-power electric socket tools.
NOTES:
- To ease with head/body assembly, a small amount of oil such as ‘3 in 1’ can be applied to the neck thread.
- If the head is accidentally cross-threaded when securing to the body, turn anti-clockwise and try again – it should then screw on easily.
- The product base is fixed to the main part of the light. 4 x Anchor bolts can be used to fix the product to the relevant surface (not supplied).
- The rubber seal supplied must be installed between the head and the body and MUST NOT be twisted to ensure a waterproof connection.
- Photocell versions – photocell is factory pre-set and cannot be changed.
- The head of the product is heavy (up to 3kg) – handle with care
CLEANING
Occasional cleaning and care are recommended for this product. Please refer to our website for the best way to clean different materials.
Full VERSA Plug & Play Range & More Information: www.lumenalights.com.
GUARANTEE
- 3 YEAR GUARANTEE
see the website for more details www.lumenalights.com.
RETURNS – Please contact us by phone or email
Lumena Lights Ltd
Centre 33 Long March
Daventry Tel: +44 1327 871161
Northants Fax: 0800 066 4410
NN11 4NR Email: sales@lumenalights.com.
Full product range & more information:
www.lumenalights.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>