Honwell Electronic Industrial 46MRF Wireless RF Remote Control and Motion Activated LED Light User Guide

Honwell Electronic Industrial 46MRF Wireless RF Remote Control and Motion

Activated LED Light

Product Information

The Wireless RF Remote Control and Motion Activated LED Light (Model No.: 46MRF) is a versatile lighting solution that combines motion detection technology with remote control functionality. It features 6 Warm White (3000K) and 6 Cool White (8000K) LEDs, a radio frequency receiver, a diffused lens, a motion sensor, and a light sensor. The light operates on 3 D batteries (not included) and has a run time of 110 hours at 300 lumens. The color temperature can be adjusted between 3000K and 8000K, providing both warm and cool lighting options. The light is designed for easy installation with a detachable mounting bracket.

Product Usage Instructions

Screw Installation Instructions

1. Prepare 3 x 1.5V D batteries (not included).
2. Remove the Mounting Bracket by pushing in the direction indicated by the OPEN arrow.
3. Drill two pilot holes in the desired mounting location, using the detachable mounting bracket as a guide.
4. Place the included screws in the pre-drilled holes and tighten them until the mounting bracket is securely attached to the surface. Avoid over-tightening.
5. Align the tabs on the light with the mounting bracket and turn the light clockwise to fasten it in place.

Operating Directions Motion Sensor

The LED Night Light is equipped with a motion sensor that operates only at night or in dark conditions. To activate the motion sensor feature:

• Press the M/ON button on the remote control.

The light will automatically turn on when motion is detected within 18 feet (5.5 meters) of the motion sensor. It will also shut off automatically after 20 seconds of no motion.

Remote Operation Using the Wireless RF Remote Control

To control the light using the remote control:

• Ensure that the light is within the remote control’s range.
• Press the power on/power off button to turn the light on or off.
• Use the adjust color of light buttons (+ / -) to change the color temperature between warm white and cool white.
• Press the White/Warm White button to switch between the two lighting options.
• Press the Motion ON (M/ON) button to activate the motion sensor feature. The light will automatically turn on when motion is detected.
• Press the Motion OFF (M/OFF) button to deactivate the motion sensor feature.
• Set an auto-off timer for 15, 30, 60, or 120 minutes using the corresponding button on the remote control.

Replacing the Remote Control Battery

If the remote control does not work to turn the LED light on, it may indicate that the battery needs to be replaced. Follow these steps:

1. Refer to the illustration on the back of the remote control.
2. Slide out the battery drawer.
3. Remove the old CR2025 button cell battery.
4. Insert a new CR2025 battery, aligning the polarity (+) (-) as indicated.
5. Slide the battery drawer back in.

IMPORTANT
This product contains a button battery. If swallowed, it could cause severe injury or death within 2 hours. Seek immediate medical attention if swallowed.

Inserting/Replacing the Batteries (LIGHT)

If the LEDs appear dim, it indicates that the batteries need to be replaced. Follow these steps:

1. Open the battery cover.
2. Install three D alkaline batteries, observing the indicated polarities (+)/(-). Batteries are not included.
3. Close the battery cover before use.

Specifications of 46MRF

• Run time: 110 hours
• Light output: 300 lumens
• Power consumption: 3.0W
• Color temperature: 3000K (Warm White) and 8000K (Cool White)
• Voltage of Light: DC4.5V (3 D batteries)
• Made in China

Warning Statement

This device complies with part 15 of the FCC Rules. It may not cause harmful interference and must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not approved by the
responsible party may void the user’s authority to operate the equipment.

Wireless RF Remote Control and Motion Activated LED Light

MODEL NO.: 46MRF
Location of Controls

1.  6 Warm White (3000K) and 6 Cool White (8000K) LEDs & Radio Frequency Receiver

2. Diffused Lens

3. Motion Sensor

4. Light Sensor

5. Battery Compartment/Mounting Bracket*
   Remote Control Buttons
   
   

6.  Power on/power off

7. Adjust color of light (+ / -)

8. White/Warm White Button

9. 4Motion ON (M/ON)/Motion OFF (M/OFF)

10. Auto-off timer for 15, 30, 60 or 120 minutes

11. Battery Compartment On back of unit/remote

Screw Installation Instructions
NOTE: Prepare 3 x 1.5V D Battery (not included).

1. Remove the Mounting Bracket by pushing to the direction with OPEN arrow.
2. Drill two pilot holes in the location where you want to mount the light. Use the detachable mounting bracket as a guide for the pilot holes.
3. Place screws (included) in pre-drilled holes. Tighten screws until mounting bracket is secure to surface. Do not over tighten.
4. Fasten the light to the mounting bracket by aligning tabs and turning light clockwise.

Operating Directions Motion Sensor
The red indicator light will FLASH when motion sensor feature is ON
The LED Night Light is designed with automatic light sensor which allows Motion Sensor only operates at night or in dark conditions. Press the “M/ON” button to turn ON motion sensor feature.

• The light will turn ON automatically when motion is detected.
• The light will also shut OFF automatically after 20 seconds when no motion is detected.
• It detects motion within 18 feet (5.5 meters) of the motion sensor.

Remote Operation Using the Wireless RF Remote Control
Press the top left button to turn all white and warm white LEDs ON. Press the top right button to turn all LEDs OFF. Adjust color of light from warm white to white with the “+” button or from white to warm white with the “-” button when light is ON. Turn the white light ON directly by pressing “White” button or turn the warm white light ON by pressing “Yellow” button when light is ON. Turn ON motion sensor feature by pressing “M/ON” button or turn OFF motion sensor feature by pressing “M/OFF” button. Light will flash once to confirm signal received. Remote control features are still working. The auto-off timer feature will be set by pressing the corresponding 15, 30, 60 or 120 button on the remote control. For best performance, point remote to the light within 80 feet (24 meters). Light will flash once to confirm signal received.

Replacing the Remote Control Battery (1 CR2025 button cell battery required)
If the Remote Control does not work to turn the LED light ON, this may be an indication that the battery needs to be replaced.

1. Follow illustration on back of remote.
2.  Slide battery drawer out.
3. Remove battery.
4. Place a new CR2025 battery in position aligning polarity (+) (-) as indicated.
5. Slide battery drawer in.

**This product contains a Button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.
Inserting/Replacing the batteries (LIGHT)
If the LEDs appear to be dim, this is an indication that batteries need to be replaced.

1.  Open Battery cover.
2.  Install all (3) three D Alkaline batteries, observing the indicated polarities (+)/(-) (Not included).
3.  Close battery cover before use.

Specifications of 46MRF

DC4.5V (3*D Battery)

Warning Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>