SOLR X5802001000 Solar Powered Wireless Charger Instruction Manual
- June 4, 2024
- SOLR
Table of Contents
X5802001000 Solar Powered Wireless Charger
Instruction Manual
Introduction
This product Is a portable power bank for all kinds of digital devices like
smartphones. tablets. hand-held gaming devices. etc.
The Micro USE is the primary charging port but the solar panel can be used as
the emergency charger.
Made with a built-in rechargeable high-performance Lithium polymer battery
cell. 4 charging outputs, wireless charging. and LED lighting lamps with
multiple functions.
Sob is your everyday essential for powering up your phone wherever you go. Say
goodbye to low battery notifications, unreliable connections, and tangled
cables: we’ve got the solution. With our solar power bank, you can wirelessly
charge your phone without an outlet. Sob is perfect for long car trips, and
sunny days at the beach. hikes In the woods, and much more. Keep your phone
running with Sob!
How to charge the power bank:
- Press the power button and ensure the blue LED light turns on.
- For solar charging, place the power bank in direct sunlight Power bank will automatically begin to charge. The power bank will not wirelessly charge if there is any Interference with the solar panel. The green LED light will stay on and the blue LED lights will flash until the battery is fully charged.
- Alternatively. use a micro VSEI cable to connect the power bank to a USE port. The LED tights will begin to flash until the battery Is fully charged.
- Remove from the power source after the battery is fully charged.
How to charge the phone:
- Press the power button and ensure the blue light turns on.
- Insert proper charging cable to one of the corresponding USE ports and plug in the phone. The phone will begin charging automatically.
- For wireless charging. ensure your phone supports wireless charging. The protection case must be 3mm or kiss or it may affect Charging Ofklenty. Cases made of metal. attachments such as magnets. grips or cards will interfere with charging.
- Place the phone faces up against the wireless charging face. The phone will automatically begin to charge.
- When the phone Is fully charged. the power bank will go Into standby mode and automatically turn off after about 60 seconds.
LED Light Function
-
There are three different light functions:
• Nigh
• Strobe -
Quickly press the power button two times to turn on the LED light to high.
-
Press one time to change to SOS lighting.
-
Press one more time to change to strobe lighting.
-
Press again to turn off the lighting.
-
Alternatively. quickly press the power button two times to turn
Specifications
Name Sok.
Model: X5802002000
Color: Black
Input: DC 5V/2A
Output a: DC 5V/1A
Output z DC 5V/2A
Type-C: DC 5V/2A
Wireless Output: 5V/1A
Solar charging 5V2cern
Li-Polymer Battery:10000rnAh
Charging
Power Status
| Power | LED 1 | LED 2 | LED3 | LED 4 | Solar LED |
|---|---|---|---|---|---|
| 10096 | ON | ON | ON | ON | ON WITH UV |
LIGHT
7596-90%| ON| ON| ON| OFF| ON WITH UV
LIGHT
5096-75%
2596-50%| ON| ON| OFF| OFF| ON WITH UV
LIGHT
ON| OFF| OFF| OFF| ON WITH UV
LIGHT
096-25%| ON| OFF| OFF| OFF| ON WITH UV
LIGHT
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference. and
- this device must accept any interference received. including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE:
This equipment has been tested and found to comply with the Limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning:
When using this product, basic precautions should always be followed, including the following:
- Read all the instructions before using the power bank.
- To reduce the risk of injury, close supervision is necessary when the power bank is used near children.
- Do not put your fingers or hands into the power bank.
- Do not strike, hit or insert any objects into the power bank or any of its ports.
- Do not expose the power bank to the water, including rain or snow.
- Use of a power supply or charger not recommended by the power bank manufacturer may result in a risk of fire or injury to persons.
- Do not use the power bank in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.
- Do not use the power bank if it has been damaged or modified. Damaged or modified power banks may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. If you see any bulging, swelling, leakage, or other abnormality from the power bank, stop using it immediately.
- Do not incinerate the battery or expose it to extreme heat or cold.
- Do not expose a power bank to fire or excessive temperature. Exposure to fire or temperature above loot may cause an explosion.
- Do not attempt to repair the battery yourself. shServicingould always be performed by a qualified repair person using identical replacement parts in order to ensure that the safety of the product is maintained. Incorrect reassembly may result in a risk of fire or injury to persons.