RYOBI R14DDE Cordless Screwdriver Instructions
- June 12, 2024
- RYOBI
Table of Contents
RYOBI R14DDE Cordless Screwdriver Instructions
SPECIAL SAFETY RULES
- Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Hold power tool by insulated gripping surfaces when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock
INTENDED USE
- Drilling into
- Wood
- Metal
- Plastic
- Ceramic
- Driving screws
MAINTENANCE
- When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
- Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
- Always wear safety goggles or safety glasses with side shields during power product operation or when blowing dust. If operation is dusty, also wear a dust mask.
- To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance.
- Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
- Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an authorized service center.
LED INDICATOR (FUEL GAUGE)
Battery charge LED colour
66% – 100% Green + Yellow + Red
33% – 66% Yellow + Red
< 33% Red
BATTERY OVERLOAD PROTECTION
This tool is designed to protect the battery from overloading. When overloading is detected, the tool will automatically switch off. To resume operation, switch the tool off and on again. If the tool fails to operate, it means battery pack is discharged and should be recharged in a compatible charger.
e-Torque control
e-Torque contol helps regulate the power output of the drill to avoid over- driving screws and damaging materials. To achieve a fl ush fi nish, it is best to select a low setting fi rst before commencing screw driving. When the e-Torque control engages, the fuel gauge LED indicator and worklight will fl ash and the drill will automatically shut down. If more power is required to drive the screw fl ush, the e-Torque contol can be adjusted accordingly. e-Torque control only operates in screw driving mode, it has no effect on drilling mode.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.
SYMBOLS
Safety Alert
GOST-R conformity
CE Conformity
Please read the instructions
carefully before starting the machine.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Product specifications
- Voltage
- Chuck
- Switch – Variable speed
- No load speed (drill mode)
- e-Torque control settings
- Torque (Hard/Soft ISO 5393)
- Maximum drilling capacity (Wood)
- Maximum drilling capacity (Metal)
- Weight (According to EPTA procedure 01/2003)
- Sound pressure level Uncertainty K
- Sound power level Uncertainty K
- Weighted root mean
- The vibration total values (triaxial vector sum) determined according to EN 60745: Vibration emission value
- Drilling into metal Uncertainty K
- Screwdriver Uncertainty K
- Battery and charger
- Compatible battery pack (not included)
- Compatible charger (not included)
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over
the total working period. An estimation of the level of exposure to vibration
should also take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly reduce
the exposure level over the total working period. Identify additional safety
measures to protect the operator from the effects of vibration such as:
maintain the tool and the accessories, keep the hands warm, and organisation
of work patterns.
Guarantee
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.
-
The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed anddedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
-
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
-
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. Theguarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
– any damage to the product that is the result of improper maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any non CE product
– any product which has been attempted to be repaired by an nonqualified professional or withoutprior authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (chemical, physical, shocks) or foreign substances
– normal wear and tear of spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– carburettor after 6 months, carburettor adjustments after 6 months
– power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
– components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube -
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to an RYOBI service station, the product should be safely packed withoutany dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
-
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.
EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
14.4V Drill Driver
Brand: Ryobi
Model number: R14DDE
Serial number range: 44417101000001 – 44417101999999
is in conformity with the following European Directives and harmonised
standards
2006/42/EC, 2004/108/EC, 2011/65/EU,
EN60745-1:2009 + A11:2010, EN60745-2-1:2010, EN60745-2-2:2010,
EN55014-1:2006+A1:2009 + A2:2011, EN55014-2:1997+A1:2001+A2:2008.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>