RYOBI R12DD Drill Driver Instructions
- June 12, 2024
- RYOBI
Table of Contents
RYOBI R12DD Drill Driver
Product Information
- Model : R12DD
- Language options: English, French, German, Spanish, Italian, Dutch, Portuguese, Danish, Finnish, Norwegian, Russian, Polish, Czech, Hungarian, Romanian, Latvian, Lithuanian, Estonian, Croatian, Slovenian, Slovak, Greek, Turkish
- Special Safety Rules: The power tool should be held by insulated gripping surfaces only to prevent electric shock. When not in use, all tools should be disconnected from the power source.
INSTALLATION
Intended Use
The tool is designed for drilling in various materials such as wood, ceramics,
plastics, fiberglass, laminates, and metals.
Battery Overload Protection
The tool has built-in protection to prevent overloading of the battery. If
overloading is detected, the tool will automatically switch off. To resume
operation, switch the tool off and on again. If the tool fails to operate,
recharge the battery pack in a compatible charger.
Symbols
The tool features safety alert symbols, voltage indication (V), revolutions
per minute (RPM), and direct current (DC) symbols.
Maintenance
When servicing the tool, use only identical replacement parts to avoid hazards
or product damage.
Avoid using solvents when cleaning plastic parts.
Do not modify the tool or use accessories not recommended for use with it.
Environmental Protection
The machine, accessories, and packaging should be sorted for environmentally-
friendly recycling.
Do not dispose of waste electrical products with household waste; recycle them
where facilities exist.
Conformance to Technical
Regulations: Read the instructions carefully before starting the machine. Wear
ear and eye protection
LED Indicator
The LED indicator on the tool shows the battery charge level.
- Green indicates : 66% – 100% charge
- Yellow indicates: 33% – 66% charge
- Red indicates: less than 33% charge.
NOTE : If only the red LED is illuminated, the battery needs to be recharged.
Product Usage Instructions
Safety Precautions
- Always hold the power tool by the insulated gripping surfaces to prevent electric shock.
- Disconnect all tools from the power source when not in use. –
- Wear ear and eye protection during operation.
- Do not modify the tool or use unauthorized accessories.
Intended Use
The tool is suitable for drilling in various materials such as wood, ceramics,
plastics, fiberglass, laminates, and metals.
Battery
Overload Protection
-
The tool is equipped with battery overload protection.
NOTE : If the tool detects overloading, it will automatically switch off. -
To resume operation, switch the tool off and on again.
NOTE: If the tool still fails to operate, recharge the battery pack in a compatible charger.
Maintenance
- Only use identical replacement parts when servicing the tool to avoid hazards or product damage.
- Avoid using solvents when cleaning plastic parts.
- Use clean cloths to remove dirt, dust, oil, grease, etc.
- Do not attempt to modify the tool or use accessories not recommended for use with it.
Environmental Protection
- Sort the machine, accessories, and packaging for environmentally-friendly recycling instead of disposing of them as waste.
- Do not dispose of waste electrical products with household waste.
- Check with your Local Authority or retailer for recycling advice.
LED Indicator
- The LED indicator on the tool shows the battery charge level.
- Green indicates a charge level of 66% – 100%.
- Yellow indicates a charge level of 33% – 66%.
- Red indicates a charge level below 33%.
NOTE : If only the red LED is illuminated, it means the battery power is low and needs to be recharged.
Important : It is essential that you read the instructions in this manual before operating this machine.
Subject to technical modifications
SPECIAL SAFETY RULES
- Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Hold power tool by insulated gripping surfaces only, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- When not in use, all tools should be disconnected from power source.
INTENDED USE
- Drilling in all types of wood
- Drilling in ceramics, plastics, fiberglass and laminates
- Drilling in metals
MAINTENANCE
- When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
- Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
- Do not attempt to modify this tool or create accessories not recommended for use with this tool.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine,
accessories and packaging should be sorted for environmental-friendly
recycling.
NOTE: If only the red LED indicator is illuminated, it means the battery power is low. The battery needs to be recharged.
BATTERY OVERLOAD PROTECTION
This tool is designed to protect the battery from overloading. When
overloading is detected, the tool will automatically switch off. To resume
operation, switch the tool off and on again. If the tool fails to operate, it
means battery pack is discharged and should be recharged in a compatible
charger.
SYMBOLS
Safety alert
Volts
Revolutions per minute
Direct current
CE conformity
Conformance to technical regulations
Please read the instructions carefully before starting the machine.
Wear ear protection
Wear eye protection
Recycle
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Product specifications
Voltage
Chuck
Switch (Variable
speed)
No load speed (drill mode):
Clutch (positions)
Maximum torque
Maximum spade bit
Weight – excluding battery pack
Battery and charger
Compatible battery pack (not included)
Compatible charger (not included)
WARRANTY – STATEMENT
All Ryobi products are guaranteed against manufacturing defects and
defective parts for a period of twenty four (24) months from the date stated
on the original invoice drawn up by the retailer and given to the end user.
Deterioration caused by normal wear and tear, unauthorised or improper use or
maintenance, or overload are excluded from this guarantee as are accessories
such as battery packs, light bulbs, blades, fittings, bags. In the event of
malfunction during the warranty period, please take the NON-DISMANTLED
product, along with the proof of purchase, to your retailer or nearest
Authorised Ryobi Service Centre. This warranty in no way affects your legal
rights concerning defective products.
AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit ryobitools.eu.
WARNING
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be used for a preliminary
assessment of exposure. The declared vibration emission level represents the
main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity
with the following standards or standardized documents.
- 2011/65/EU, 2006/42/EC, 2004/108/EC,
- EN 55014-1:2006+A1:2009+A2:2011,
- EN 55014-2:1997+A1:2001+A2:2008,
- EN 60745-1: 2009+A11:2010
- EN 60745-2-1:2010
- EN 60745-2-2:2010.
- Sound pressure level [K=3dB(A)]: 67,0 dB(A)
- Sound power level [K=3dB(A)]: 78,0 dB(A)
Weighted root mean
The vibration total values(triax vector sum) determined according to
- EN60745: Drilling into metal, vibration emission value ah, D = 2,2 m/s2 (Uncertainty K = 1,5 m/s2)
- Screw driving without impact, vibration emission value ah = 1,4 m/s2 (Uncertainty K = 1,5 m/s2)
Machine: DRILL DRIVER
Techtronic Product Development Limited 24/F, CDW Building, 388 Castle Peak Road, Tsuen Wan, Hong Kong
Brian Ellis Vice President – Engineering
Hong Kong, Aug. 02, 2012
Authorised to compile the technical file: James Dickinson
Techtronic Industries (UK) Limited Medina House, Fieldhouse Lane, Marlow,
Bucks, SL7 1TB, United Kingdom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>