wilfa E-600 Electric Scooter User Manual

wilfa E-600 Electric Scooter User Manual

The Device & Accessories

Accessories

• Hex Wrench

• Charging Adapter
  

Functions

Specifications

Features

• Superior Aviation Aluminum Alloy.
• IP 56 Ingress Protection.
• Real-time Temperature Monitoring, Short Circuit / Low Voltage / Overcurrent / Overcharging Protection.
• Digital Speedometer Display, Easy to Read Speed.
• Real-time 5 Bars Battery Display.
• 1~3 Speed Gear, Press Button to Switch.
• Multi information Display.

Control panel

• Power ON/OFF: Long press the button for 3 seconds, all icons are lighting, showing speed & battery.
  

• Headlight ON/OFF: Click the button once when unit is on (Headlight ON:
  

• Click the button for two times to change the speed gear from 1 to 3 levels, LED display P1 / P2 / P3. Max speed is increasing from P1 to P3.
  

• Click the button three times to switch display showing speedometer Km/h / voltage V / current A.
  

Before riding – Assembly

1. Straighten the stem and fasten the folding mechanism by lifting the handle upwards.

2. Lift the handlebar grips upwards, and ensure they are locked in place.
   

3. Push power button to see that everything works.
   

Folding and Carrying

Make sure that the scooter’s turned off. To fold, unlock the folding mechanism, and bend the handlebar stem to hook the hanging hole on the pedal. To open, remove the hook from the hanging hole on the pedal, erect the handlebar and lock the folding structure.

Hold the handlebar stem with either one hand or both hands to carry.

APP

Make sure Bluetooth is on on the phone. Open the Eway scooter app, click the corresponding model in device list to connect. You can find the app under EWAY SCOOTER name in App store or Google shop or by scanning the corresponding QR code. The E-scooter will beep when APP is connected with E-scooter. For more details on functionality, see www.wilfa.com/eway

Before first ride
Step 1: Check that the E-scooter has no loose screws, or that anything feels abnormal. This should be done every time you want to ride the scooter. Check that wheels turn easily and that brakes work properly.
Step 2: Wear protective equipment.

Step 3: Push with one leg to move forward.

Step 4: Touch the throttle slightly and try to put two legs on the deck.

Step 5: During riding, try to release the throttle and pull the brake lever.

Step 6: Try to use the headlight. This is done by pushing the power button once when the unit is on.

Warnings

• Wear protective equipment.
  

• Do not ride in rain or cross puddles. Excessive exposure to water can damage the scooter.
  

• Do not load over 125kg.

• Ride slowly in special cases.
  

• Make sure both feet are on the deck when riding for maximum stability.
  

• Do not tread the back of the fender.
  

• Do not let go of the handlebar while riding.

• Do not ride upstairs or downstairs, or over obstacles.
  

• Do not hold a child during riding.
  

• Do not ride on highway or motor vehicle road unless allowed in your country.
  

• Do not take sharp turns.
  

Firmware Upgrade
Check for upgrades regularly in Apple store or Google play.

Cruise Control
The scooter has a cruise control. If you keep the same speed for 3~5 seconds, the E-scooter will be in cruise-control mode(running at constant speed on flat road) Please use cruise-control only on flat road. The cruise control is cancelled by pushing the brake. It can also be adjusted in the app.

Error Description
Some of the errors can be fixed by the user. if you are uncertain how to fix, please contact the service center.

well connected.2. Replace the display.3. Replace the control board.
E1| Encountered obstacles whichE-scooter can’t get over| 1. Release the accelerator and stop braking.2. Restart.3. Replace the brake lever.4. Replace the accelerator.
E3| Hall is abnormal| 1. Check whether the Hall wire plug of the motor is loose.2. Check whether the motor cable is damaged.3. Replace the motor.4. Replace the control board.
E4| Brake system malfunction| 1. Release the brake.2. Restart.3. Replace the brake lever.
E5| Throttle fault| 1. Release the accelerator.2. Restart.3. Replace the accelerator.
BL| Low voltage alarm| 1. Stop riding and get scooter charged.2. Restart.3. Check if App has been wrongly upgraded.4. Replace the control board.
BH| High voltage alarm| 1. Check whether scooter has been fully charged, riding the scooter at low speed, avoid braking suddenly when scooter is fully charged.2. Restart.3. Check if App has been wrongly upgraded.4. Replace the control board.
BP| Over voltage, emergency| 1. Check whether scooter has been fully charged, riding the scooter at low speed, avoiding braking suddenly when scooter is fully charged.2. Restart. Check if App has been wrongly upgraded.3. Replace the control board.
H1| Motor high temperature| 1. Stop riding or ride scooter at low speed, avoid climbing.2. Check whether the motor wire is damaged, and whether the temperature signal wire of the motor wire is short- circuited to the ground.3. Replace the motor.
H2| Control board high temperature| 1. Stop riding or ride scooter at low speed, avoid climbing.2. Check the installation of control board radiator.3. Replace the control board.
H3| Control board super high temperature| 1. Stop riding or ride scooter at low speed, avoid climbing.2. Check the installation of control board radiator.3. Replace the control board.
LR| Over current| 1. Release the accelerator.2. Restart.3. Replace the control board.
S1| Short circuit| 1. Get the motor disconnected and restart scooter. If this alarm has not been cleared, get control board replaced; otherwise, all-clear, replace the motor.
S2| Lack of phase, mos tube drive failure| 1. Restart and turn scooter on standing still2. Replace the control board.
SN| Lack of series number| 1. Check whether the firmware version iscorrect.2. Reset the serial number.

Battery

Temperature Effect on Battery
Battery power will vary with the temperature, mileage per charge will have slight difference under different temperature, and following table is just for your reference. Range will also be dependent on terrain, weight of driver and other factors.

Charging
The device has a built-in lithium battery, no extra battery installation is required, just charge the device when it indicates low battery. Plug in the power source after inserting the charger plug, this can prevent potential risk to ensure a safer charge. It takes around 4hrs to get 100% charged, when the red lights turn into green, the charging is completed. If not in urgent need, please wait until charging is complete before unplugging.

Cleaning and Maintenance

Cleaning

• Please place the E-scooter in cool and ventilate places to release heat.
• Please avoid high temperature or moist.
• Please avoid water into the E-scooter to prevent electric shock,especially water drops from the charger cable to the the charging port.

When cleaning

• Please make sure the E-scooter is off.
• Please use soft cloth to clean the E-scooter.
• Please don’t use water to wash the E-scooter or place E-scooter in water.

When storing the scooter

• Please place the E-scooter in cool and ventilated places (temperature -10~40 °C, relative humidity 0~90%).
• Please don’t place objects on the E-scooter.

Battery Pack Maintenance
When the E-scooter is fully charged, please check the voltage of the battery in APP. Normal voltage is 31V~42V. If the voltage is not in this range, please contact the service center for battery pack maintenance. Please charge the E-scooter at least one time each month, to extend the battery pack life time. Please do not disassemble, assemble or change the battery by yourself.

Regular Maintenance
Please do not disassemble or assemble the E-scooter without the guide or help from professional maintenance personell. Check that all screws are fastened, that wheels are turning freely, brakes work properly and that no foreign objects are stuck. Check for visible signs of wear and contact us if you are in doubt if you need to change parts or have any questions.

After sales service

You can find answers to many questions as well as spare parts at www.wilfa.com/eway. If you have a problem you can’t solve yourself, please contact the store where you bought the scooter for further help.

Adjust the handlebar

If the handlebar and its stem sway during riding, use the hexagon wrench to tighten the screws on the folding mechanism.

 This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling free of charge.

Nydalsveien 24, 0484 Oslo, Norway
Tel : +47 67 06 33 00
Web: www.wilfa.com
E-mail : [email protected]

References

• Wilfa - Norwegian quality since 1948 – Wilfa AS
• Wilfa – Norsk kvalitet siden 1948
• Choose Site
• Best i test el sparkesykler - norsk leverandør | E-Way
• Wilfa – Norsk kvalitet siden 1948
• E-Way - Wilfa
• Wilfa – Norsk kvalitet siden 1948
• Hem - Wilfa
• E-Way - Wilfa

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>