THE SWIMSUIT 120V 50/60hz Dryer User Manual
- June 12, 2024
- THE SWIMSUIT
Table of Contents
THE SWIMSUIT 120V 50/60hz Dryer
Product Information
The Swimsuit Dryer is a device designed to quickly remove water from swimsuits, increasing user satisfaction with pool experiences. It also serves as a low-cost maintenance solution for the purchaser. The dryer should only be used to dry swimsuits and is not intended for any other purpose.
Proper Usage and Liability
It is important to follow the instructions provided to ensure proper usage of
the Swimsuit Dryer. Neither The Swimsuit Dryer Company, the purchaser, nor the
facility where the dryer is installed will be liable for any damages to
swimming costumes resulting from improper usage. The appliance should not be
used by individuals with reduced physical, sensory, or mental capabilities,
unless they have been provided with supervision or instruction.
Identification & Certification
For information regarding the Swimsuit Dryer’s serial number, voltage and
frequency, manufacturing date, and certification, please refer to the label
located on the bottom right-hand side of the device.
Product Usage Instructions
Items Supplied with the Swimsuit Dryer:
- Shipping Box and Packaging
- Securing Bracket
- User Manual
- Fixing Screws
- T30 Screwdriver
- Mounting Bracket
- Swimsuit Dryer Cleaning Brush
- Cleaning Towel & Cleaner
Location and Pre-Installation
Before installing the Swimsuit Dryer, it is recommended to consider the
following:
- Choose a suitable location for installation.
- Ensure the transit bar underneath the dryer is removed.
Transit Bar
It is crucial to remove the transit bar located underneath the Swimsuit Dryer
before use.
Purpose
The purpose of the Swimsuit Dryer is to give the user the facility to remove water from their Swimsuits quickly, thus increasing their satisfaction with the pool experience, encouraging the user to continue to use the pool, sauna, steam room and other wet facilities offered. The Swimsuit Dryer has been designed, not only to increase the user’s satisfaction, but to also offer a low-cost maintenance solution for the purchaser.
Proper usage and liability
The Swimsuit Dryer is intended to dry Swimsuits ONLY, neither The Swimsuit
Dryer Company, the purchaser, nor the facility where the Swimsuit Dryer is
installed will not be liable or take responsibility for any damages to
swimming costumes where the user has not properly followed the instructions
given.
The appliance is not to be used by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they have 0been given supervision or instruction
Identification & Certification
Please see the label located on the bottom right-hand side of The Swimsuit
Dryer for the following Information:
- Serial Number
- Voltage and Frequency
- Manufactured Date
- Certification.
The Swimsuit Dryer Information
Where Would You Expect to Find the Swimsuit Dryer
The Facilities that a user could expect to find The Swimsuit Dryer installed
in are:
- Health Clubs
- Gyms
- Public Swimming Pools
- Hotels with Leisure Facilities
- Spas
- Holiday Resorts
- Universities
- Wellness Centers
- Recreation Centers
- Cruise Liners
- Any Commercial Property with a pool or wet area. available and suitable for private
Items Supplied with the Swimsuit Dryer
The Swimsuit Dryer will be supplied with the following items. The items listed
below must be kept should the unit experience a fault in or out of warranty,
and to carry out any necessary maintenance.
- Shipping Box and Packaging
- User Manual
- T30 Screwdriver
- Swimsuit Dryer Cleaning Brush
- Securing Bracket
- Fixing Screws
- Mounting Bracket
- Cleaning Towel & Cleaner
Location and Pre-Installation.
We recommended all Next Generation Swimsuit Dryers are Installed:
-
In a changing/Locker room, outside a changing/Locker room, in a corridor, or in an area where facility users have access, a dry or semi wet area, and a location where the wastewater can be removed.
The Swimsuit Dryer Must NOT be installed by anyone in any of the following locations: -
Any location where local laws and regulations do not permit mains equipment to be installed.
TRANSIT BAR
MAKE SURE YOU REMOVE THE TRANSIT BAR FROM UNDERNEATH THE SWIMSUIT DRYER!
If the Transit Bar is not removed from underneath the Swimsuit Dryer, it will not work.
Wall Mounted Installation (Wall & Counter Top Models)
Secure the Wall Plate
-
Please ensure the wall can support approximately 30kg/ 66lbs of weight.
-
Place the wall mount on the wall and ensure the top is 1 meter from the floor, check with a spirit level to ensure the Mounting bracket is level. Mark your locating holes and drill the holes, insert wall fixings, then use the mounting screws to secure the bracket to the wall.
After securing the mounting bracket to the wall ensure it is level and fastened to the wall securely! -
Place the Swimsuit Dryer onto the mounting bracket and connect it to the power and drainage.
Wall Mounted Model – Installation Diagram 
Counter-Top Model – Wall Installation Diagram 
Counter-Top Installation
Surface Preparation
- Please ensure the countertop or tabletop can support approximately 30kg/ 66lbs of weight.
- Measure your surface using the dimensions shown on the installation diagram and cut this out.
- Place the Swimsuit Dryer into the hole and connect it to the power and drainage.
Counter-Top Model – Counter-Top 
Connecting the Swimsuit Dryer to a waste outlet
If you have not purchased our built-in water tank, the Swimsuit Dryer will
need to be connected to you waste water outlet. This can be done by a
professional tradesman.
Simply connect the waste outlet to your external plumbing.
Example of Swimsuit Dryer plumbed into the wall. 
Ensure there is sufficient ventilation underneath the unit.
Electrical Connection
Please consult with a qualified electrician and ensure he complies with the local regulations.
Receptacle/ Electrical Socket
If you are in the USA, UK, EU, or country that has the same connections you
can order your Swimsuit Dryer with a plug. Simply plug the Swimsuit Dryer in
and you are ready to use.
** Weatherproof electrical enclosures must comply to all local Electrical Regulations.
Hard Wired
If you need to hard wire your Swimsuit Dryer into a Fused Socket or
Receptable please contact a qualified electrician.
Representative images ONLY
Maintenance & Cleaning
The Swimsuit Dryer has been manufactured to be maintenance FREE.
Cleaning Requirements
Your Swimsuit Dryer should be cleaned weekly, or as required.
Equipment Required:
- Cleaner and Disinfectant
- Hand Towel
- Screwdriver
DO NOT pour large amounts of water or cleaning solution directly into the Swimsuit Dryer.
Cleaning Instructions
To keep your Swimsuit Dryer clean and sanitized, we recommend you use a
general disinfectant.
Weekly Cleaning Requirements
Step 1
Spray the outer body of the Swimsuit Dryer with the disinfectant and wipe it
down with the cleaning towel.
Monthly Cleaning Requirements
- Step 1
- Lift the lid and remove the Top Cover.
- Spray the cleaner inside the drum/ basket and down between the drum and liner.
- Step 2
- Re-fit the top ring cover making sure to tighten the security screws.
- Operate the dryer for 10 seconds to remove any cleaner from inside the drum.
Technical Specifications
- Weight : 20kg / 44lbs free standing
- 25kg / 55lbs fully boxed
- Energy : Standby: approximately 3 watts Per hour
- Running: approximately 0.97 watts per cycle.
- Safety Details:
- 5 Year Service Life PAT Tested
- GFI Installed PTO Installed
- Low Voltage LEDs IP65 Enclosures
- Overload Protected IP54 Brake Motor
- Safety Brake UL 94
- Voltage : 110-120 Volt 50/60 Hz local supply
- Mounting : Wall Mounted or Counter-Top
- Waste Hos e: 60cm from the unit
- 23.62” from the unit
- Custom Length Available
- Basket Volume : 2 litres
- Waste Outlet : Connects directly to waste outlet: 32mm / 1 1/4
- Hose Internal Diameter 28.0mm / 1.10”
- Hose Outside Diameter 33.5mm / 1.31”
- Noise Emission:
- Approximately 50 – 60dB when used correctly
- Warranty (FULL) : 2 Year Global Guarantee – New
- 1 Year Global Guarantee – Factory Refurbished
- ** Inclusive of shipping, parts, and labor.
- Extended warranty: 3 Year Motor and Brake