Breezary 30006-BK Chandelier 48 Inch Black Indoor Chandelier Ceiling Fan Instruction Manual

Breezary 30006-BK Chandelier 48 Inch Black Indoor Chandelier Ceiling Fan

Product Information

The 48-inch Ceiling Fan with Light (Item #30006-BK) is a versatile and stylish addition to any room. It comes with a remote control for easy operation and features a sleek black design. The fan is designed to provide both cooling and lighting functionality,
making it a practical and convenient choice for your home.

Product Features

• 48-inch size for optimal air circulation
• Includes remote control for easy operation
• The sleek black design adds a modern touch to any room
• Comes with a built-in light for added functionality
• Includes all necessary hardware for installation

Product Usage Instructions

Step 1: Fan Installation

1. Take out the fan downrod.

2. Remove the cotter pin and bolt from the download.

3. Take out the fan motor housing.

4. Loosen the jam screw in the yoke until it is flush with the inside surface.

5. Place the downrod inside the canopy, canopy cover, and yoke cover.

6. Route wires exiting the motor through the yoke cover, canopy, and download.

7. Insert the bolt through the hole in the download, being careful not to damage or cut the fan wires.

8. Tighten the bolt and secure it with the cotter pin through the hole in the end of the bolt.

9. Secure the downrod in position by tightening the jam screws.

10. Slide the yoke cover down until it is flush with the motor housing.
    Step 2: Hanger Installation

11. Secure the hanger to the metal outlet box.

12. Hang the ceiling fan on the hanger, aligning the hanger ball groove with the hanger boss.
    Step 3: Mounting Blade Brackets to Blades

13. Place a blade screw through a fiber washer and a blade.

14. Align the screw with the corresponding hole in the blade bracket.

15. Repeat this process with the remaining screws and tighten them.
    Step 4: Attaching the Fan Blade Bracket

16. Attach the blade bracket to the motor using the blade bracket screws.
    Step 5: Assembling the Lamp Housing

17. Feed the wire through the center hole of the lamp housing.

18. Fix the lamp housing to the motor using screws.

19. Connect the plugs from the motor and LED lights.
    Step 6: Assembling Lamp Connecting Parts and Glass

20. Screw the screw into the screw hole on the motor end and tighten it.

21. Lock the lampshade onto the screw using decorative nuts and decorative flat pads.
    Step 7: Receiver Installation

22. Place the receiver in the hanger.
    Step 8: Wiring the Fan

23. Follow the wiring diagram to connect the fan to the ceiling.

24. Match the white wire from the ceiling to the white wire from the fan, and the black wire from the ceiling to the black wire from the fan.

Please refer to the complete user manual for more detailed instructions and safety precautions.

Safety Information

READ AND SAVE THESE INSTRUCTIONS

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked” Acceptable for Fan Support of 35 lbs. (15.9 kg) or less.”
4. Do not place objects in the path of the blades.
5. To clean the fixture. tum off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment grounding the conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
7. All set screws must be checked and retightened where necessary before installation.

WARNING : To reduce the risk of electrical shock or not use this fan with any solid-state fan speed Lil control device. It will permanently damage the electronic circuitry.
WARNING : To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert balancing the blades, or clean the fan. Do not insert &. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked “acceptable for fan support of 35 lbs. (15.9 Kg) or less and use screws provided with the outlet box.
WARNING: To avoid possible electrical shock, tum Lil the electricity off at the main fuse box before wiring.
WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control/switch.
CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.
CAUTION: Please use care when working around or cleaning the fan to avoid injury or damage often.
CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Dimension Reference

Hardware Included

Fan Parts Included

Step1 MOUNTING

• Take out fan downrod.

• Remove cotter pin and bolt from downrod.

• Take out fan motor housng.

• Loosen jam screw in yoke until it is flush with the inside surface.
  Yoke

• Place the downrod inside the canopy, canopy cover, and yoke cover.

• Route wires exiting motor through yoke cover, canopy and downrod.

• Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires.

• Tighten bolt. Secure with cotter pin through hole in the end of the bolt.

• Secure downrod in position by tightening jam screws.

• Slide yoke cover down and it will flush with the motor housing.

CAUTION: To ensure the wobble-free operation and to avoid damage to the fan, the download and the set crew must be completely tightened

Step2

WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To UUCSA Listed
Outlet Box Marked Acceptable for Fan Support And Use Mounting Screws Provided With The Outlet Box

• Secure hanger to the metal outlet box.
• The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss.

Step3 Mount Blade Brackets To Blades

• Place blade screw through fiber washer and blade.
• Align with the corresponding hole in the blade bracket.
• Repeat with the remaining screws and tighten.

Step4 Attaching the Fan Blade Bracket
Attach the blade bracket to the motor with blade bracket screws.

Step5 Assembling the Lamp housing

• Feed the wire through the center hole of the lamp housing.
• Fix the lamp housing to the motor with screws.

Connect the plugs from the motor and LED

Step6 Assembling Lamp connecting parts and glass

• Screw the screw into the screw hole on the motor end and tighten it. screw
• Lock the lampshade onto the screw using decorative nuts and decorative flat pads.

Step7 The receiver installation
Put the receiver in the hanger

Step8 Wiring the Fan
Wiring according to the wiring diagram.

NOTE: Once ground wires are connected, carefully tuck all wires and barrettes into the metal box making sure that the wires are clear of the hemisphere and down rod when positioned in the hemisphere and downrod when positioned in the mounting bracket.

Step9 Attaching the Canopy and Canopy cover
Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely. Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)

FUNCTION INSTRUCTION OF EMITTER

• Open the battery cover on the hand-held remote and install a battery, pair of AAA of the emitter(1.5V) that are not included. and receiver.

• If the emitter can not control the fan, learning code matching mode is used between the emitter

• Turn on the power switch, and press the”SETUP” key within 3 seconds, the receiver issued a”tick” two sounds, and the pairing code is successful. If not successful, turn off the power for a minute and repeat the above. normally or not, correction of the positive and negative, full or empty of the power.

• when the emitter cannot control the receiver, please check the battery switch touching remote-controlled products nearby, then check whether they work, because remote hen the emitter cannot control the receiver, please check is there any existence of similar
  controlled products with the same frequency will disturb each other.

• Please take out the battery from the emitter when left unused for a long time. When installing the fan, the fan ceiling cover doesn’t press the antenna(or other wire), it is easy to break down the wire and short-circuited.

1. Main switch off fan and light
2. Fan forward rotating Natural wind
3. Speed controller Mach code/Turn off fan Timer
4. Light switch on/off Fan reversal rotating

TROUBLESHOOTING

If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects.If you experience any faults, please check this troubleshooting guide. The Balancing kit should only be used if there is an unacceptable amount of fan wobbles after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1

|

If fan does not start.

| □  Check the main and branch circuit fuses or breakers.

□  Check the line wire connections to the fan and switch wire connections in the

switch housing.

□  Check the battery in the remote control.

□  Ensure you are in the normal range of 10-20 feet.

2

|

If fan sounds noisy.

| □  Ensure all motor housing screws are snug.

□  Ensure the screws that attach the fan blade bracket to the motor hub are tight.

□  Ensure the wire nut connections are not rattling against each other or the interior

wall of the switch housing.

□  Allow a 24-hour “breaking in” period. Most noises associated with a new fan

disappear during this time.

□  If you are using the Ceiling Fan light kit, ensure the screws securing the

glassware are tight. Check that the light bulbs are also secure.

□  Ensure the canopy is a short distance from the ceiling. It should not touch the

ceiling.

□  Ensure your outlet box is secure and rubber isolator pads were used between the

mounting plate and outlet box.

3

|

If fan wobbles.

| □  Check that all blades are screwed firmly into blade holders.

□  Check that all blade holders are tightened securely to motor.

□  Make sure that canopy and mounting bracket are tightened securely to ceiling

junction box and junction box is mounted firmly to ceiling joist.

□  Most fan wobble problems are caused when blade levels are unequal.Check this

level by selecting a point on the ceiling above the tip of one of the blades keeping measure within 1/8 in.Rotate the fan until the next blade is positioned for measurement.Repeat for each blade.If all blade levels are not equal you can adjust blade levels by the following procedure.To adjust a blade tip down insert a washer(not supplied)between the blade and blade holder at the screw closest to the motor.To adjust a blade tip up insert washer(not supplied)between the blade and blade holder at the two screws farthest from the motor.

□  If blade wobble is still noticeable interchanging two adjacent (side by side)blades

can redistribute the weight and possibly result in smoother operation.

4

|

If light does not work.

| □  Check blue wire from fan to make sure it is connected to hot wire from the house.

□  Check for loose or disconnected wires in fan switch housing.

□  Check for loose or disconnected wires in light kit.

□  Check for faulty light bulbs.CAUTION:Make sure main power is turned off before

entering switch housing.

□  If the fan light shuts off shortly after being switched on it may be due to excessive

current demand.Turn off power to the fan and replace the light bulbs with lower wattage bulbs.Turn on power to the fan using the pull chain,wall switch,or remote control (whichever is installed on the particular fan).

1. Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
2. Turn off the fan and allow it to come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of the blade.
3. Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
5. Remove the clip and install a balancing weight to the top of the blade along the center line near the point where the clip was positioned.
6. If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights

References

• Breezary Ceiling Fan - Online Ceiling Fan Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>