NCXX UNX-05G Portable 5G Modem User Manual

NCXX UNX-05G Portable 5G Modem

Product Information

The UNX-05G Portable 5G Modem is an online device designed for users who need mobile internet access. It allows users to connect to the internet anywhere and at any time.

Part Names and Functions

• A label with IMEI information is attached to the bottom of the product. Do not remove this sticker as the IMEI number is required for repair and after-sales service.
• Place the product with the logo side facing up to improve the radio wave condition of the 5G/4G antenna.
• To reset the product to its factory default settings, insert the tip of the SIM eject pin into the RESET button hole while the product is powered on. Hold down the RESET button for at least 5 seconds.

Indicator Lamp

The indicator lamps on the product provide information about its communication status.

High-Temperature Lamp:

• Red Lighting: Product Condition – Stop Operation (Functional limitation)
• Orange Flashing (Lights on, lights off at the same interval): Product Condition – Normal Operation
• OFF: Power Lamp

Power Lamp:

• Cyan Lighting: Product Condition – Boot Sequence
• Blue Lighting: Product Condition – 15W mode
• Green Lighting: Product Condition – 7.5W mode
• Orange Lighting: Product Condition – 4.5W mode
• Red Lighting: Product Condition – Lack of supply capacity
• Cyan Flashing (Lights on, lights off at the same interval): Product Condition – Factory Reset

5G/4G Connection Lamp:

• Blue Lighting: 5G Antenna Level – 2 bars
• Blue Flashing (Long light on, short light off): 5G Antenna Level – 1 bar
• Blue Flashing (Lights on, lights off at the same interval): LTE Antenna Level – 2 bars
• Blue Flashing (Short light on, Long light off): LTE Antenna Level – 1 bar
• Green Lighting: Network searching
• Green Flashing (Long light on, short light off): Network searching
• Green Flashing (Lights on, lights off at the same interval): Network searching
• Green Flashing (Short light on, Long light off): Network searching
• Cyan Flashing: Out of service Standby State for Modem SIM PIN Lock State / SIM Error ME-PIN Lock State APN Error
• Red Flashing (Lights on, lights off at the same interval): Red Lighting – Wi-Fi connection lamp
• Orange Lighting: Wi-Fi mode – 2.4GHz

Wi-Fi Connection Lamp:

• Blue Lighting: Wi-Fi mode – 2.4GHz5GHz DFS
• Orange Lighting: Wi-Fi OFF
• Red Flashing (Lights on, lights off at the same interval): Ethernet port connection lamp

Ethernet Port Connection Lamp:

• Green Lighting: Link speed – 1000Mbps
• Orange Lighting: Link speed – 100Mbps
• OFF: Ethernet No Link / Disable

Product Usage Instructions

Inserting the SIM Card:

1. Before inserting or removing the SIM Card, ensure that the product is turned off.
2. Insert the tip of the SIM eject pin into the SIM Card tray hole and push it firmly until the tray comes out. Avoid pushing it in at an angle to prevent damage or malfunction.
3. Pull out the SIM Card tray.
4. Place the nano SIM (4FF) Card into the tray with the IC (metal) side facing down. Ensure that the IC Card is securely placed in the tray.

Part Names and Functions

1. Nano SIM Card tray

2. Reset button
   The product settings can be restored to the factory default settings.

3. USB Type-C port
   Connect USB Type-C cable (sample).

4. Ethernet
   Connect LAN cable.

5. Temperature rise warning indicator
   This LED indicates that the temperature of this product has risen and communication is restricted or stopped.

6. Power indicator
   Indicator for power supply status.

7. Ethernet indicator
   Indicator for LAN status.

8. Wi-Fi indicator
   Indicator for Wi-F status.

9. 5G/4G indicator
   This indicator indicates the type and strength of the radio wave being received.

10. Special Screws

11. label
    SSID, encryption key, etc. can be confirmed.

• A label printed with IMEI information (product identification number) and other information is attached to the bottom of this product. Do not remove the sticker, as the IMEI number will be required for repair requests and after-sales service.
• Place the product with the logo side turned up. The radio wave condition of the 5G/4G antenna is improved.
• With the product powered on, insert the tip of the SIM eject pin (sample) into the RESET button hole. Hold down the RESET button for at least 5 seconds. The product will automatically restart and the settings will be restored to its factory default settings.

Indicator lamp

The following indicator lamps inform you of the communication status of the product.

High-Temperature lamp

(Lights on ⇔ lights off at the same interval)

Normal Operation| OFF

Power lamp

Power Rule

| 15W mode| Blue Lighting
7.5W mode| Green Lighting
4.5W mode| Orange Lighting
Lack of supply capacity| Red Lighting
Factory Reset| Cyan Flashing

(Lights on ⇔ lights off at the same interval)

5G/4G connection lamp

5G

| Antenna Level : 4 – 5ber| Blue Lighting
Antenna Level : 3ber| Blue Flashing

(Long light on ⇔ short light off)

Antenna Level : 2ber| Blue Flashing

(Lights on ⇔ lights off at the same interval)

Antenna Level : 1ber| Blue Flashing

(Short light on ⇔ Long light off)

LTE

| Antenna Level : 4 – 5ber| Green Lighting
Antenna Level : 3ber| Green Flashing

(Long light on ⇔ short light off)

Antenna Level : 2ber| Green Flashing

(Lights on ⇔ lights off at the same interval)

Antenna Level : 1ber| Green Flashing

(Short light on ⇔ Long light off)

Network searching| Cyan Flashing
| (Lights on ⇔ lights off at the same interval)
---|---
Out of service

Standby State for Modem

| Red Flashing

(Lights on ⇔ lights off at the same interval)

SIM PIN Lock State / SIM Error| Red Lighting
ME-PIN Lock State| Orange Lighting
APN Error| Red

Wi-Fi connection lamp

(Lights on ⇔ lights off at the same interval)

Wi-Fi OFF| OFF

Ethernet port connection lamp

Inserting the SIM Card

Before inserting/removing the SIM Card, ensure you turn off the product. Insert/remove the card with the logo side of the product turned up.

1. Insert the tip of the SIM eject pin (sample) into the SIM Card tray hole. Push the tool firmly in until the SIM card tray comes out. Pushing this other than straight in may cause damage or malfunction.
2. Pull out the SIM Card tray.
3. Put the nano SIM (4FF) Card into the SIM Card tray with the IC (metal) side facing down. Check the direction of the IC Card, and place it security in the SIM Card tray.
4. Insert the SIM Card tray fully into the product straight and horizontally with logo side facing up.

Set the connection destination

1. Connect the USB Type-C cable (sample) to the USB Type-C port on this product and the USB Type-C port on the PC.
   Insert the cable straight to the back.

2. Launch the Web browser

3. Input the URL
   Enter “http://192.168.0.1/” in the URL entry field and press “Enter”.

4. Enter the user name and password on the login screen
   Enter “admin” in the User Name field and “admin” in the Password field and click “Log in”.
   Enter lower-case single-byte alphanumeric characters.

5. Set the connection destination
   Select “WAN Settings” → “Profile Management” and click “New Profile”.
   Set the connection destination (APN), user name, and password obtained from your provider.
   Click “Save” to save the profile.

6. Select the connection destination
   If multiple profiles are registered, select a profile from “Carrier Name” and click “Apply”.

Troubleshooting

• This product does not turn on
  • Is the USB TYPE C cable (sample) correctly plugged into the product
  • Is the USB TYPE C cable (sample) correctly plugged into the PC?
  • Some energy-saving PCs may have the power to this product turned off. If the indicator lamp of this product is off, the power to this product may not be supplied, so check the power status according to the instruction manual of the PC.
• The produ ct becomes hot during operation
  • This product and the USB TYPE C cable (sample) may become warm during operation, but there is no p roblem with operation.
• Unable to communicate
  • Is the 5G/4G connection lamp lit in red?
  • Make sure the SIM card is installed correctly.
  • The SIM card PIN code may be valid, PIN locked, or completely locked. Check your PIN code settings.
  • Is the 5G/4G connection lamp blinking in red? Disconnect the USB TYPE C cable (sample) connected to this product and then reinsert it to restart this product If the problem persists, relocate this product in a location where radio waves are more likely to reach.
  • Depen ding on the nature of radio waves or the congestion of radio waves depending on the time of day, communication may be interrupted or the service may not be able to be used normally. Please wait for a while before using.

Trademarks

• Microsoft®, Windows®, Internet Explorer®, and Microsoft Edge are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.
• Mac, macOS, Safari are trademarks or registered trademarks of Apple Inc. in the United Statesand ot her countries.
• Intel and Intel are trademarks of Intel Corporation in the United States and other countries.
• QR Code is a registered trademark of DENSO WAVE INCORPORATED.
• Ethernet and Ethernet are registered trademarks of FUJIFILM Business Innovation Corpo ration.
• USB Type C™ is a trademark of USB Implementers Forum.
• Wi Fi®, Wi Fi Alliance®, Wi Fi CERTIFIED®, Wi Fi Protected Access® (WPA), WPA2™, WPA3™ and Wi Fi Protected Setup™ are trademarks or registered trademarks of Wi Fi Alliance.
• LTE is a registered t rademark of the European Telecommunications Standards Institute (ETSI).
• Google, Android, and Google Chrome are trademarks of Google LLC.
• Adobe Reader and Acrobat Reader are trademarks or registered trademarks of Adobe Systems Incorporated in the United Sta tes and other countries.
• All other company and product names are trademarks or registered trademarks of their respective owners. The TM and ® marks may be omitted in the text.

FCC Regulations

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient/relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

Radio Wave Exposure Information

This Product meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards I include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of this Device MiFi (FCC ID SLKUNX 05G ) has been tested against this SAR limit. The SAR value of the device is 1. 12 W/kg, which meets the standards. SAR information on this can be viewed online at http://www.fcc.gov/oet/ea/fccid/ fccid/. Please use the device’s FCC ID number for the search. This device was tested for typical operations 10mm from the body. To maintain compliance with FCC RF exposure requirements, a 10mm separation distance should maintain to the user’s body.

European RF Exposure Information

This device meets the guidelines for exposure to radio waves. Your device is a 5G Portable Modem. As recommended by international guidelines, the device is designed not to exceed the limits for exposure to radio waves. These guideli nes were developed by the Inter n ational Commission on Non-I onizing Radiation Protection (ICNIRP), an independent scientific organization, and include safety measures designed to ensure the safety of all users, regardless of age and health. The Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the body when using a device. The SAR value is determined at the highest certified power level in laboratory conditions, but the actual SAR level during operation can be well below th e value. This is because the device is designed to use the minimum power required to reach the network. The SAR limi t adopted by Europe is 2.0W/kg averaging over 10 grams of tissue, t the SAR value of the device is 1.54W/kg, which meets the standards.

Regulatory conformance

• Statement

  • Hereby, NCXX Inc. declares that this device UNX
  • 05G is in compliance with the following.
  • Directive: RED 2014/53/EU, RoHS 2011/65/EU,
  • The full text of the EU Declaration of Conformity information and the most recent information about accessories & software is available at the following internet address: https://www.ncxx.co.jp.

• FrequencyBands and Power
  Frequency bands in which the radio equipment operates: Some bands may not be available in all countries or all areas.

  • Please contact the local carrier for more details.
  • LTEBand: 1/2/3/4/5/7/8/18/19/20/26/28/41/42:25.7dBm,
  • 5G NR n1/n3/n28/n77/n78/n79: 25.7dBm,
  • Wi-Fi 2.4G: 20dBm, Wi-Fi 5G5150-5350MHz:23dBm,
  • Wi-Fi 5G5470-5725MHz: 23dBm. W52/53 Indoor Use only.

About Portable 5G Modem

A portable 5G Modem is a kind of online device designed for the user who may use mobile internet to get online, and the user may access the internet anywhere and anytime.

References

• 株式会社ネクス

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>