BEEZOOM1940 40W RGBW 4 In 1 LED Moving Head User Manual
- June 12, 2024
- BEEZOOM
Table of Contents
40W RGBW 4 In 1 LED Moving Head
User Manual
Unpacking
Thank you for choosing our fixture. For your own safety, please read this
manual before installing the device. This manual covers the important
information on installation and applications. Please install and operate the
fixture with following instructions. Meanwhile, please keep this manual well
for future needs.
This fixture is made of a new type of high temperature strength of engineering
plastics and cast aluminum casing with nice outlook. The fixture is designed
and manufactured strictly following CE standards, complying with international
standard DMX512 protocol. It’s available independently controlled and linkable
with each other for operation. And it is applicable for large-scale live
performances, theater, studio, nightclubs and discos.
4-IN-1 LEDs(RGBW) which features high brightness and stability. Please
carefully unpack it when you receive the fixture and check whether it is
damaged during the transportation. And please check whether the following
items are included inside the box:
Moving Head———One
Hanging Bracket—–Two
Safety Cable———one
Signal Cable—-One
Power Cable—-One
User Manual—-One
Product dimension
Safety Instructions
CAUTION! Bc careful with your operations. With a dangerous voltage you
can Suffer a dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for
the user to follow the safety instructions and warning notes written in this
user manual.
Important:
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.
If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could
damage the device. Leave the device switched off until it has reached room
temperature.
This device falls under protection-class I. Therefore it is essential that the
device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of
this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this
would be the case, replacement of the cable must be done by an authorized
dealer.
Always disconnect from the mains, when the device is not in use or before
cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the
power cord.
During initial start-up some smoke or smell may arise. This is a normal
process and does not necessarily mean that the device is defective, it should
decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans
and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall
be exclusively replaced by the manufacturer or his service agent or a similar
qualified person in order to avoid a hazard.
Operation Instructions
-The fixture is for beam wash and effect use.
-Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
-This light should be keep away from strong shaking during any transportation or movement.
-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
-Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the fixture.
-Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
-Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside
walking paths, seating areas, or in areas were the fixture might be reached by
unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation
area can hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety
attachment, succahs an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing
the fixture from a periodic safety inspection of all installation material and
the fixture. If you lack these qualifications, do not attempt the installation
yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting
the main power cord to the appropriate wall outlet.
Clamp Mounting: The product provides a unique mounting bracket assembly
that integrates the bottom of the base, the included “Omega Bracket,” and the
safety cable rigging point in one unit (see the illustration below). When
mounting this fixture to truss be sure to secure an appropriately rated clamp
to the included omega bracket using a M10 screw fitted through the center hole
of the “omega bracket”. As an added safety measure be sure to attached at
least one properly rated safety cable to the fixture using on of the safety
cable rigging point integrated in the base assembly
Regardless of the rigging option you choose for our fixture, always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.
DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your
controller and the other side to the male 3-pin XLR input of the moving head.
You can chain multiple
Moving heads be connected together through serial linking. The cable needed
should be two core, screened cable with XLR input and output connectors.
Please refer to the diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.
DMX Channels
22 channels mode
| CH | Function | DMX | Details |
|---|---|---|---|
| 1 | Pan | 0-255 | Pan movement control |
| 2 | Pan fine | 0-255 | Pan fine control |
| 3 | Tilt | 0-255 | Tilt movement control |
| 4 | Tilt fine | 0-255 | Pan fine control |
| 5 | Pan/Tilt speed | 0-255 | Speed from fast to slow |
| 6 | ZOOM | 0-255 | Zoom |
__
7
| __
LENS rotation
| 0-127| 0 to 60 degree
128-191| Unlimited clockwise rotation from fast to slow
192-255| Unlimited anticlockwise rotation from fast to slow
8| Dimmer| 0-255| 0-100 linear dimmer from dark to bright
__
9
| __
Strobe
| 0-3| No function, Light off
4-200| Strobe with the same step from slow to fast
201-255| Random strobe from slow to fast
10| R| 0-255| 1-100% Red linear dimmer from dark to bright
11| G| 0-255| 1-100% Green linear dimmer from dark to bright
12| B| 0-255| 1-100% Blue linear dimmer from dark to bright
13| W| 0-255| 1-100% White linear dimmer from dark to bright
14| Color temperature| 0-255| Linear color temperature control
15| Marco| 0-255| Marco color change
__
16
| __
Static effect
| 0-9| No function
10-84| Each 5 DMX value is a kind of static effect(15 kinds)
85-255| 16th kind of effect
__
17
| __
Dynamic effect
| 0-9| No function
10-199| Each 5 DMX value is a kind of dynamic effect(38 kinds)
200-255| 39th kind of effect
18| Dynamic effect speed| 0-127| Anti-clockwise rotate from fast to slow,
operate against 17 CH
128-255| Clockwise rotate from slow to fast, operate against 17 CH
__
19
| __
LED ring strobe
| 0-3| No function, Light off
4-250| LED ring strobe
251-255| No function, Light on
20| LED ring macro| 0-51| Macro color
52-255| Dynamic effect, every 4 DMX channel is one kind of effect, totally 51
kinds
21| Macro speed| 0-255| LED ring macro effect from slow to fast
22| Reset| 0-239| No function
240-255| Reset with 5 seconds
26 channels mode
| CH | Function | DMX | Details |
|---|---|---|---|
| 1 | Pan | 0-255 | Pan movement control |
| 2 | Pan fine | 0-255 | Pan fine control |
| 3 | Tilt | 0-255 | Tilt movement control |
| 4 | Tilt fine | 0-255 | Pan fine control |
| 5 | Pan/Tilt speed | 0-255 | Speed from fast to slow |
| 6 | ZOOM | 0-255 | Zoom |
__
7
| __
LENS rotation
| 0-127| 0 to 60 degree
128-191| Unlimited clockwise rotation from fast to slow
192-255| Unlimited anticlockwise rotation from fast to slow
8| Dimmer| 0-255| 0-100 linear dimmer from dark to bright
__
9
| __
Strobe
| 0-3| No function, Light off
4-200| Strobe with the same step from slow to fast
201-255| Random strobe from slow to fast
10| R| 0-255| 1-100% Red linear dimmer from dark to bright
11| G| 0-255| 1-100% Green linear dimmer from dark to bright
12| B| 0-255| 1-100% Blue linear dimmer from dark to bright
13| W| 0-255| 1-100% White linear dimmer from dark to bright
14| Color temperature| 0-255| Linear color temperature control
15| Marco Color| 0-255| Marco color change
__
16
| __
Static effect
| 0-9| No function
10-84| Each 5 DMX value is a kind of static effect(15 kinds)
85-255| 16th kind of effect
__
17
| __
Dynamic effect
| 0-9| No function
10-199| Each 5 DMX value is a kind of dynamic effect(38 kinds)
200-255| 39th kind of effect
18| Dynamic effect speed| 0-127| Anti-clockwise rotate from fast to slow,
operate against 17 CH
128-255| Clockwise rotate from slow to fast, operate against 17 CH
19| Background R| 0-255| Background color Red dimmer
20| Background G| 0-255| Background color Green dimmer
21| Background B| 0-255| Background color Blue dimmer
22| Background W| 0-255| Background color White dimmer
__
23
| __
LED ring strobe
| 0-3| No function, Light off
4-250| LED ring strobe
251-255| No function, Light on
24| LED ring macro| 0-51| Macro color
52-255| Dynamic effect, every 4 DMX channel is one kind of effect, totally 51
kinds
25| Macro speed| 0-255| LED ring macro effect from slow to fast
26| Reset| 0-239| No function
240-255| Reset with 5 seconds
36 Channels mode
| CH | Function | DMX | Details |
|---|---|---|---|
| 1 | Red | 0-255 | Red dimmer |
| 2 | Red Fine | 0-255 | Red fine control |
| 3 | Green | 0-255 | Green dimmer |
| 4 | Green Fine | 0-255 | Green fine control |
| 5 | Blue | 0-255 | Blue dimmer |
| 6 | Blue Fine | 0-255 | Blue fine control |
| 7 | White | 0-255 | White dimmer |
| 8 | White Fine | 0-255 | White fine control |
| 9 | CTO | 0-255 | Color temperature linear control |
| 10 | Macro color | 0-255 | Marco color effect |
| 11 | strobe | 0-3 | No function, Light off |
| 4-103 | Strobe with the same step from slow to fast | ||
| 104-107 | No function, light up | ||
| 108-207 | Pulse strobe from slow to fast | ||
| 208-212 | No function, light up | ||
| 213-251 | Random strobe from slow to fast | ||
| 252-255 | No function, light up | ||
| 12 | Dimmer | 0-255 | 0-100 linear dimmer from dark to bright |
| 13 | Dimmer Fine | 0-255 | Dimmer fine control |
| 14 | Pan | 0-255 | Pan movement control |
| 15 | Pan Fine | 0-255 | Pan fine control |
| 16 | Tilt | 0-255 | Tilt movement control |
| 17 | Tilt Fine | 0-255 | Pan fine control |
| 18 | Function | 0-255 | |
| 19 | Reset | 0-250 | No function |
| 251-255 | Reset with 5 seconds | ||
| 20 | Zoom | 0-255 | ZOOM |
| 21 | LENS Rotation | 0-127 | 0 to 60 degree |
| 128-191 | Unlimited clockwise rotation from fast to slow | ||
| 192-255 | Unlimited anticlockwise rotation from fast to slow | ||
| 22 | Shape Selection | 0-255 | Selecting shape(0-70 workable) |
| 23 | Shape Speed | 0-255 | Shape speed control |
| 24 | Shape Fade | 0-255 | Shape fade |
| 25 | Shape R | 0-255 | Shape in Red color |
| 26 | Shape G | 0-255 | Shape in Green color |
| 27 | Shape B | 0-255 | Shape in Blue color |
| 28 | Shape W | 0-255 | Shape in White color |
| 29 | Shape Dimmer | 0-255 | Shape dimmer 0-100% |
| 30 | Background Dimmer | 0-255 | Background dimmer 0-100% |
| 31 | Shape Transition | 0-255 | Shape change |
| 32 | Shape Offset | 0-255 | Shape offset |
| 33 | Foreground strobe | 0-255 | Foreground strobe control |
| 34 | Background strobe | 0-255 | Background strobe control |
| 35 | Background selection | 0-255 | Background selection |
| 36 | Frequency | 0-255 | Shape and frequency selectable |
78Channels mode
| CH | Function | DMX | Details |
|---|---|---|---|
| 1 | Red | 0-255 | Red dimmer |
| 2 | Red Fine | 0-255 | Red fine control |
| 3 | Green | 0-255 | Green dimmer |
| 4 | Green Fine | 0-255 | Green fine control |
| 5 | Blue | 0-255 | Blue dimmer |
| 6 | Blue Fine | 0-255 | Blue fine control |
| 7 | White | 0-255 | White dimmer |
| 8 | White Fine | 0-255 | White fine control |
| 9 | CTO | 0-255 | Color temperature linear control |
| 10 | Macro Color | 0-255 | Marco color |
__
__
__
11
| __
__
__
strobe
| 0-3| No function, Light off
4-103| Strobe with the same step from slow to fast
104-107| No function, light up
108-207| Pulse strobe from slow to fast
208-212| No function, light up
213-251| Random strobe from slow to fast
252-255| No function, light up
12| Dimmer| 0-255| 0-100 linear dimmer from dark to bright
13| Dimmer Fine| 0-255| Dimmer fine control
14| Pan| 0-255| Pan movement control
15| Pan Fine| 0-255| Pan fine control
16| Tilt| 0-255| Tilt movement control
17| Tilt Fine| 0-255| Pan fine control
18| Function| 0-255| Revered channel, no function at this moment
19| Reset| 0-250| No function
251-255| Reset with 5 seconds
20| Zoom| 0-255| Zoom
__
21
| __
Zoom Rotation
| 0-127| 0 to 60 degree
128-191| Unlimited clockwise rotation from fast to slow
192-255| Unlimited anticlockwise rotation from fast to slow
22| Red dimmer 1| 0-255| LED 1 red dimmer
23| Green dimmer 1| 0-255| LED 1 green dimmer
24| Blue dimmer 1| 0-255| LED 1 blue dimmer
25| Red dimmer 2| 0-255| LED 2 red dimmer
26| Green dimmer 2| 0-255| LED 2 green dimmer
27| Blue dimmer 2| 0-255| LED 2 blue dimmer
…| ………| ………| ………
76| Red dimmer 19| 0-255| LED 19 red dimmer
77| Green dimmer 19| 0-255| LED 19 green dimmer
78| Blue dimmer 19| 0-255| LED 19 blue dimmer
Display instruction
Key Features
Voltage: AC100V～240V 50-60HZ
Rated Power: 760W
LED Source: 19x40W high power RGBW 4 in 1 LEDs
Zoom: 7°-50°
Strobe: 0-25Hz
Control Mode: DMX512,Sound-actived,Master/slave
DMX Channels: 22/26/36/78 four channel mode
Dimmer: 0-100% linear dimmer
Pan: 540°+16 bit fine
Tilt: 220°+16 bit fine
Display: LCD colorful display
IP: IP20
Fixture dimension: 405234440mm
N.W:15.2 Kg
G.W: 18.7 Kg
Package dimension: 623951 CM (1pc/ctn)
Special Points.
- Each LED can be controlled individually. With unique honeycomb designed lens.
- The front lens can rotate without limitation in forward and reverse direction to create amazing effects.
- Can be used as beam, wash or effect light use (Kaleida effects).
- With a extra LED ring for eye-candy effect, LED ring with macro effect.
Maintenance and Cleaning
The following points have to be considered during the inspection:
- All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded.
- There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing).
- Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
- The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
CAUTION! Disconnect from mains before starting maintenance operation.
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the lights.
- Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust.
- Clean the fan each week.
- A detailed electric check by approved electrical engineer each three month,
make sure that the circuit contacts are in good condition, prevent the poor
contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device.
Please refer to the instructions under “Installation instructions”.Should you need any spare parts, please order genuine parts from your local dealer.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>