Dual DC207BT Single Din Car Stereo Bluetooth Receiver Owner’s Manual

Dual DC207BT Single Din Car Stereo Bluetooth Receiver

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove trim ring from unit.
• Remove 2 transit screws located on top of the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

Wiring Diagram

Control Locations

• Faceplate Release

• Band / Go Back

• Power / Mute Bluetooth Talk

• Volume Knob

• Audio / Menu Eject

• USB Port

• Auxiliary Input

• Preset 6 / Folder Up

• Preset 5 / Folder Down

• Preset 4 / Play / Pause

• Preset 3 / Intro
  Preset 2 / Random

• Preset 1 / Repeat Display

• Mode

• Reset (behind faceplate)

• Tune / Track Up

• Tune / Track Down

Remote Control

General Operation

• Power On/Off
  Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off.

• Mode
  Press MODE to select between AM/FM, CD player, Bluetooth, auxiliary and USB. Modes of operation are shown in the display.
  NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.

• Auxiliary Input
  The DC207BT offers a 3.5 mm auxiliary input port on the front panel of the unit for connecting an audio device, MP3 player, etc. Press MODE to select auxiliary input mode.

• Volume
  Adjust volume using volume knob (00-46).

• Display
  Press DISP to show the clock. During playback of MP3/files, ID3 tag information, elapsed time, track number and file/folder names will automatically rotate on the display.

• Reset
  Press RESET upon initial installation or if abnormal operation occurs.

• Set the Clock
  With the unit on, press and hold DISP until the clock begins to flash, then release. Turn the volume knob to the right to adjust the hours or to the left to adjust the minutes.

• 12/24-hour Clock
  The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).

• Setup Menu
  Press and hold AUDIO for more than 3 seconds to access the setup menu. Press AUDIO momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.

General Operation - Setup Menu

Menu Function        Options Action

Auto Station Store| AUTO STORE| Press the volume knob to seek and save 6 strong stations in the current band. ( Tuner mode only)

Local/Distance Tuning

| LOCAL OFF| Activates distance tuning ( Tuner mode only ).
LOCAL ON| Activates local tuning for strong station reception only (Tuner mode only).

Tuner Frequency Spacing

| FREQ USA| Programs the unit to USA tuner spacing.

(200kHz for FM and 10kHz for AM). (Tuner mode only)

FREQ EURO| Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM). (Tuner mode only)
Auxiliary Input| AUX ON| Enables the front panel 3.5mm auxiliary input.
AUX OFF| Disables the front panel 3.5mm auxiliary input.
Beep Confirmation| BEEP OFF| Disables the confirmation beep.
BEEP ON| Enables the confirmation beep.
Programmable Turn On Volume| PRO-VOL #| Programs unit to always turn on at a specific volume (default is OFF). Any volume level 1-30 can be selected.
Power On Message| MSG OFF| Disables power on message. (Example: GOOD MORNING)
MSG ON| Enables power on message to be displayed.

Scrolling Option

| SCROLL 15 SP| Programs unit to scroll information every 15 seconds (default).
SCROLL ONCE| Programs unit to scroll once then show the first 10 characters on display
SCROLL ON| Programs unit to scroll continuously.
SCROLL OFF| Programs the unit to show the first 10 characters on display.
Demonstration Mode| DEMO OFF| Disables the demonstration mode.
DEMO ON| Enables the demonstration mode.

Bluetooth

| BT ON| Enables Bluetooth functionality.
BT OFF| Disables Bluetooth functionality.

Auto Answer

| ANSWER AUTO| Programs unit to automatically answer every incoming phone call after 2-3 rings.
ANSWER MANUAL| Programs unit to require the  button to be pressed to answer incoming phone calls (default).

General Operation

• Audio
  Press AUDIO momentarily to select between Bass, Treble, Balance and Fader.

  • BASS
  • TREBLE
  • BALANCE
  • FADER
  • EQ
  • LOUD
  • SOURCE LEVEL

•   Bass
  Press AUDIO until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).

• Treble
  Press AUDIO until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).

• Balance
  Press AUDIO until BAL appears then rotate volume knob left/right to adjust (BAL 12L – BAL 12R). BAL EVEN represents equal balance

• Fader
  Press AUDIO until FAD appears then rotate volume knob left/right to adjust (FAD 12R – FAD 12F). FAD EVEN represents equal fader

AM/FM Tuner Operation

• Seek Tuning
  Press TUNE or TUNE   momentarily to seek to the next strong station.

• Manual Tuning
  Press and hold TUNE or TUNE  until “MANUAL” appears, then press TUNE or TUNE momentarily
  Note: Seek and manual tuning functions are reversed if Seek Priority is set to SEEK 2 in the setup menu (refer to page 7 for details on setting Seek Priority).

• Band
  Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands.

• Storing and Recalling Station Presets
  Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button.

• Automatically Store Stations
  Press and hold AUDIO/MENU for more than 3 seconds to find auto store in the display. Then press volume knob to automatically store strong 6 stations in the current band.

CD Player Operation

• Insert CD
  With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback.

• Eject CD
  Press EJECT to eject the CD. The unit will change to previous mode of operation. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD.

• Track Select
  Press TRACK to skip to the beginning of the next track. Press TRACK  to return to the beginning of the current track. Pressing TRACK  again skips to the beginning of the previous track.

• Fast Forward/Reverse
  Press and hold TRACK  or TRACK  on the remote control to fast forward or reverse a track.

• Pause
  Press l/ II to temporarily stop CD playback. Press l/ II again to resume playback

• Intro
  Press INT to enter the Intro menu, then turn the volume knob to select one of the following options:

  • OFF – Cancels the INT function.
  • ALL – Plays the first 10 seconds of each track.

• Repeat
  

• Random
  Press RPT to enter the Repeat menu, then turn the volume knob to select one of the following options:

  • ALL – Plays all tracks on CD.
  • TRACK – Continuously repeats selected track.

• CD-R/CD-RW Compatibility
  Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. In addition, the following CDs may be incompatible with this unit:
  CDs exposed to extreme temperatures or direct sunlight for extended periods of time, CDs recorded in which a recording session failed or a re-recording was attempted and, or encrypted or copy-protected CDs which do not conform to the audio CD-DA red book recording standard

CD Player Operation - MP3 Files

• Playing an MP3 CD
  When an MP3 encoded disc is first inserted, “DISC READ” will appear in the display. Depending on the number of files and folders, this may take several seconds.

• Displaying Information
  Press DISP to select between song title, artist, file name, folder name, track number, and clock/elapsed time. “NO ARTIST” or “NO TITLE” will be displayed if the MP3 file contains no ID3 tag information. “ROOT” will be displayed if the directory name of a root folder is not labeled.

• Title Icon
  This icon will illuminate when the song title is displayed.

• Artist Icon
  This icon will illuminate when the artist name is displayed.

• Folder Icon
  This icon will illuminate when the folder name is displayed.

• File Icon
  This icon will illuminate when the file name is displayed.

• Character Support
  Maximum character display information

  • Track name – 32 character maximum
  • Directory name – 32 character maximum
  • Song title – 32 character maximum
  • Artist name – 32 character maximum
  • Song title and Artist Name will only be displayed if included with the MP3 file. When referring to MP3 playback, the following terms are synonymous:
  • File name and track name
  • Folder name and directory name

• Media Compatibility
  The following types of discs/files are compatible:

  • CD-ROM (ISO), CD-R, CD-RW

  • CD-DA

  • MP3 data
    The following types of discs/files are not compatible:

  • Discs recorded with Track At Once or packet writing

  • MP3 PRO format

  • MP3 playlists

  • WAV format

• Playback Order
  MP3 playback sequence is based on recorded order of files and begins in the root folder of the disc. Any empty folders or folders that do not include MP3 files are skipped. This unit may not play files in the order they were recorded in. Refer to your recording software’s user’s manual for more information.

• Compatible Recording Formats

  • ISO9660 level 1

  • ISO9660 level 2

  • Yellow Book MODE 1

  • Yellow Book MODE 2 FORM 1

  • Multi session

  • Maximum files – 999

  • Maximum folders – 255

  • Maximum folder levels – 8

  • MPEG-1/2/2.5 Audio Layer-3
    ISO9660 standards:

  • Maximum nested folder depth is 8 (including the root folder).

  • Valid characters for folder/file names are letters A-Z (all caps), numbers 0-9, and “_” (underscore). Some characters may not be displayed correctly, depending on the character type.

  • This device can play back discs in Joliet, Romeo, and other standards that conform to ISO9660. MP3 written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly.

• Additional MP3Information
  An internal buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping. When playing a disc recorded with regular audio files (CD- DA or .WAV) and MP3 files, the unit will play the MP3 files only. Only MP3 files with filename extension (.mp3) can be played. Do not attempt to play discs which contain non-MP3 files with the MP3 extension.

• Sampling Frequency Rates MP3
  8kHz ~ 48kHz

• Transfer Bit rates MP3
  32kbps ~ 320kbps constant Variable bit rates
  Note: Some files may not play or be displayed correctly, depending on sampling rates and bit rates.

• MP3 Tag Display
  ID3 tags Version 1.0 to 2.4. This model will not display ID3 Version 2.4 or greater tags.

• Recommended Settings
  For best results, use the following settings when burning an MP3 disc: 128kbps or higher constant bit rate 44.1kHz or higher sampling frequency

USB Operation

• Connecting a USB Device (sold separately)
  To play MP3 files from most USB mass storage devices, line up the USB connector and insert the USB device into the unit’s USB port.

• Playing Music
  When a USB device is first connected, “USB READ” will appear in the display and playback will begin momentarily. Depending on the number of files and folders, it may take several seconds for the device to begin playing. If no valid MP3 files are detected, “NO FILE” will be displayed and the last mode will be resumed.

• Track Select
  Press TRACK  to skip to the beginning of the next track. Press TRACK to return to the beginning of the

• Fast Forward and Reverse
  Press and hold TRACK  or TRACK  on the remote control to fast forward or reverse a track.

• Pause
  Press l/ II to temporarily stop USB playback. Press l/ II again to resume playback.

• File Search
  Press SELECT to enter the file/folder search mode.

• Step 1
  A list of all the folders from the USB device will be displayed.
  Note: Any files located in the root directory will be located in the folder named “ROOT”. Press SELECT to view the files on the root folder.

• Step 2
  Turn the volume knob to cycle through all the folders on the device and press SELECT to choose the desired folder. The list of files in the selected folder will be displayed. Turn the volume knob to cycle through the list of files.
  Note: Pressing GO BACK when viewing the contents of a folder will return to the list of folders on the USB device. Press GO BACK again to exit the search menu.

• Step 3
  Once the desired song is displayed, press SELECT to begin playback of the desired song.
  Note: Due to differences in USB device transfer speeds, it is recommended to limit each folder to less than 30 songs.

• Displaying Information
  When a file is accessed, the clock and elapsed time will be displayed. Press DISP momentarily to select between song title, artist, file name, folder name, track number and clock/elapsed time. “NO TITLE” will be displayed if no song title information is available. “NO ARTIST” will be displayed if no artist information is available.

• Song Title Icon
  This icon will illuminate when the song title is displayed..

• Artist Icon
  This icon will illuminate when the artist name is displayed.

• Folder Icon
  This icon will illuminate when the folder name is displayed.

• File Icon
  This icon will illuminate when the file name is displayed.

• Folder Access

  • Press to select the previous folder.
  • Press to select the next folder.
    Note: Folder access is only available on devices with more than one folder.

• Repeat
  Press RPT to enter the Repeat menu, then turn the volume knob to select one of the following options:

  • ALL – Plays all tracks on the device.
  • TRACK – Continuously repeats selected track.
  • FOLDER – Continuously repeats all files in selected folder.

• Random
  Press RDM to enter the Random menu, then turn the volume knob to select one of the following options:

  • OFF – Cancels the RDM function.
  • ALL – Plays all tracks in random order.
  • FOLDER – Plays all tracks in folder in random order
    Note: Random mode is retained in memory when selecting between other modes and when the unit is turned on/off.

• Intro
  Press INT to enter the Intro menu, then turn the volume knob to select one of the following options:

  • OFF – Cancels the INT function.
  • ALL – Plays first 10 seconds of each track.
  • FOLDER – Plays first 10 seconds of each track in folder.

• Character Support
  Maximum character display information

  • Track name – 32 character maximum
  • Directory name – 32 character maximum
  • Song title – 32 character maximum
  • Artist name – 32 character maximum
  • Song title and artist name will only be displayed if included with the MP3 file.

• Media Compatibility
  The following types of files are compatible:

  • MP3 data
    The following types of files are not compatible:

  • MP3 PRO format

  • MP3 playlists

  • WAV format

• Playback Order
  MP3 playback sequence is based on order the files are copied to the USB device and begins in the root folder. Any empty folders or folders that do not include MP3 files are skipped. Depending on your software, the playback order may vary.

• Playback Capacity

  • Maximum number of files: 999
  • Maximum number of folders: 255 plus the root directory
  • Maximum number of files in each folder and root: 999
    Note: If the number of files/folders exceeds the maximum outlined above, the additional files/folders will be ignored.
    Note: Devices that exceed the maximum number of files or folders may not function properly.

• USB Device Compatibility
  Due to the differences of USB devices, some devices may not be compatible. USB devices must be ‘mass storage class’ and formatted to the FAT or FAT32 file system in order to ensure compatibility.

• Additional MP3Information
  Only MP3 files with filename extension (.mp3) can be played. Do not attempt to play non-MP3 files with the MP3 extension.

• Sampling Frequency Rates MP3
  8kHz ~ 48kHz

• Transfer Bit rates MP3
  32kbps ~ 320kbps constant Variable bit rates
  Note: Some files may not play or be displayed correctly, depending on sampling rates and bit rates.

• MP3 Tag Display
  ID3 tags Version 1.0 to 2.4
  Note: If an invalid ID3 tag version is detected, “NO SUPPORT” will scroll on the display.

Bluetooth® Operation

• Pairing a New Device
  Before you can use a Bluetooth device, it must be paired and connected. Make sure that Bluetooth is activated on your device before you begin the pairing process. The unit broadcasts the pairing signal constantly when no devices are currently connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details. The device name is ”DUAL BT” The Bluetooth passcode ”1234″
  Note: The unit can be in any mode of operation when pairing is performed.

• Pairing Additional Devices
  If a device is currently connected, press and hold to disconnect the current device before a new device can be paired. Then begin the pairing sequence from the new Bluetooth device.

• Connecting a Paired Device
  Most Bluetooth devices support the auto-connect feature, and will connect automatically if the device is in range when the unit is powered-on. If your device was previously paired but does not connect, use these instructions below.

  • If your most recently connected Bluetooth device becomes disconnected or does not reconnect, press and hold from Bluetooth mode to reconnect your mobile device.
  • To connect a previously paired device that was not recently connected:

1. Press and hold to disconnect any connected mobile devices when Bluetooth is paired. Press and hold to connect Bluetooth device again when Bluetooth is not paired.
2. The paired device name will appear on the LCD once it is connected.
3. Turn the volume knob to cycle through the list of devices.
4. Press the volume knob to cycle through the list of recent calls up to ten and select the phone number to dial when Bluetooth is paired. NONE appears on the LCD if there are no recent calls.

• Disconnecting a Device
  Press and hold for 3 seconds to disconnect a connected device. The device will remain paired and appear in the SEARCH menu, but not be connected.
  Note:  Placing a phone call from your cell phone will also initiate Bluetooth function.

• Recent Calls List
  Press SELECT from Bluetooth mode to view recent calls dialed, received or missed while connected to the head unit. Turn the volume knob to cycle through the recent phone numbers. Press SELECT or to dial

• Redialing the last number
  To redial the last phone number, press from Bluetooth  mode. Press or SELECT again to redial the phone number.

• Receiving a phone call
  Incoming phone calls will automatically appear on the display and a ring tone will be heard.
  Note: The volume of the ring tone depends on the volume level of the unit. The incoming ring tone may not be heard if the volume is set to a low level or mute is activated.

  • Press to receive the incoming phone call.
  • Press and hold to refuse the incoming phone call.
    Note: If Auto Answer is set to ON in the setup menu, all phone calls will be received automatically.

• Ending a Phone Call
  During an active phone call, press During an active phone call, press  If the phone call was received when listening to music in another mode, the unit will resume the previous mode.

• Streaming Audio
  The unit supports A2DP (advanced audio distribution profile) wireless streaming audio from your Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:

  • Press  to skip to the next available audio track.
  • Press  to skip to the previous audio track.
  • Press l to toggle between play and pause during playback.

Streaming Audio Operation

The unit supports A2DP (advanced audio distribution profile) wireless streaming audio from your Bluetooth mobile device directly to your head unit. You can also control your music from the front panel of the head unit using AVRCP (audio video remote control profile).
Notes:

• To stream music to your head unit, your mobile device must support the A2DP and AVRCP Bluetooth profiles. Check the owner’s manual of your mobile device for details.
• Streaming audio must be enabled from your mobile device. This option will vary depending on the device. Some devices allow streaming audio to be disabled.

After pairing, connecting and enabling streaming audio from a compatible mobile device, begin playing music using the music player on your mobile device. Once the music is playing, the following functions can be used to control the music:

• The button will skip to the next available audio track.
• The button will skip to the previous audio track.
• The l button will toggle between play and pause during playback.

Note: Some Bluetooth devices may not fully support these commands.

Troubleshooting

Unit will not turn on (no power)

| Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage| Check connections for proper voltage (11~16VDC)
Black wire not connected| Check connection to ground
Fuse blown| Replace fuse

Unit has power (but no sound)

| Speaker wires not connected| Check connections at speakers
One or more speaker wires touching each other or touching chassis ground| Insulate all bare speaker wires from each other and chassis ground

Unit blows fuses

| Yellow or red wire touching chassis ground| Check for pinched wire
Speaker wires touching chassis ground| Check for pinched wire
Incorrect fuse rating| Use fuse with correct rating

Excessive skipping

| Unit is not mounted correctly or backstrap is not secure| Check mounting sleeve and backstrap support
Physical defect in media (CD, CD-R or CD-RW)| Check media for scratches

ERR FILE appears on display

| Disc read error| Press eject or RESET
Focus error or disc is in upside down| Press eject or RESET
NO FILE appears on display| No playable MP3files found on the device| Check the device for valid MP3 files

Unit will not accept a disc

| CD mechanism position out of alignment| Press EJECT to reset CD mechanism position
CD transit screws still in place| Remove 2 transit screws located on top of the unit
NO SUPPORT appears on display| An invalid ID3 tag version is present| Version 1.0 to 2.0 ID3 tags are supported.

Limited One Year Warranty

This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.dualav.com.

What to do?

1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.
4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:
   • Call us toll-free at 1-866-382-5476
   • E-mail us at cs@dualav.com

Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual
or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specifications

• CD Player
  Frequency response: 20Hz-20kHz Channel separation @ 1kHz: >60dB D/A converter: 1 Bit

• FM Tuner
  Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: >30dB Frequency response: 30Hz- 13kHz

• AM Tuner
  Tuning range: 530kHz-1710kHz Usable sensitivity: <42dBu Frequency response: 30Hz-2.2kHz

• General
  USB Charge: 1A Speaker output impedance: 4~8 ohms Line output voltage: 1.2 Volts RMS Dimensions: 7″ x 7″ x 2″ (178 x 178 x 50 mm)
  Design and specifications subject to change without notice.

CEA-2006 Power Standard Specifications (reference: 14.4VDC +/- 0.2V, 20Hz~20kHz) Power Output: 16 Watts RMS x 4 channels at 4 ohms and < 1% THD+N Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>