BLASTKING PROBEAM7R 7R 230W Beam Moving Head User Manual

PROBEAM7R
7R 230W Beam Moving Head

User Manual

**** This manual contains important information.
Please read before operating fixture.

INTRODUCTION

Thank you for selecting this product. The Moving Beam 7R is a beam moving head with OSRAM lamp. It produces stunning beam effects, ideal for stages, conernts, TV studios, live shows, night clubs, etc. To optimize the performance of this product, please read the user manual carefully before use.
1.1 Unpacking
The following items are included in the box:

• 1 x PROBEAM7R
• 1 x Power Cord
• 2 x Mounting Brackets
• 1 x User Manual

Carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Contact your supplier immediately and retain packing material for inspection if any part is missing or damaged.
1.2 Safety Instructions

Warning!!! To reduce the risk of fire, electric shock, or injury to persons, follow these important safety instructions:

• The product is for indoor use only.
• Always turn off, unplug power and allow fixture to cool before servicing.
• Ensure that fixture is properly grounded.
• Please keep this User Guide for future consultation.
• Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture.
• Always disconnect from power before servicing or replacing fuse.
• Make sure power cord is never crimped or damaged.

Caution! Never touch the device during operation! The housing may heat up.
Caution! Never look directly into the light source, as sensitive persons may suffer an epileptic shock.
Caution! The electric connection must be carried out only by a qualified electrician.

1.3 Technical Data

• Power supply: AC 100-240V 50-60Hz
• Power consumption: 350W
• Lamp: OSRAM 7R 230W lamp, 8,000K, 2,000 hrs
• Beam angle: 0-4° adjustable
• 1 Colour wheel: 14 COLOURs + white
• 1 Gobo wheel: 17 fixed gobos + open
• Colour rainbow + Gobo shaking
• 8-facet rotating prism
• Motorized focus
• Frost-filter
• DMX-controlled or stand-alone with master/slave
• 2 DMX modes: 16ch (Simple)/20ch (Expand)
• Pan : 540° (16 bit) Tilt: 270° (16 bit)
• Automatic Pan/Tilt correction
• Mechanical shutter and adjustable speed strobe effect
• Touch LCD display with Joy Wheel
• Dimension: 523×337×511mm
• Weight: 19.5 kg

1.4 Product overview

SETUP

2.1 Mounting
The Moving Head is fully operational in any mounting position, hanging upside- down, side mounted, or set on a flat llevel surface, etc.
IMPORTANT!!! Safety cables must always be used when unit is celling or truss mounted. The safety cable must be capable of holding 10 times the weight of the fixture. The equipment must be installed by professionals.

DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable material (decoration articles, etc.) within a distance of min. 0.5 m.
2.3 AC Power
The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered directly from a switched circuit. This unit cannot be run on a rheostat or dimmer circuit even if used solely for a 0% to 100% switching.
WARNING!!! All fixtures must be connected to circuits with a suitable Earth Ground.
The occupation of connection-wire is as follows:

2.4 DMX Linking
You can link the Moving Head 7R to a DMX controller using a 3- or 5-pin DMX cable.

It is recommended to use a DMX terminator for installations where the DMX cable has to run a long distance, or is in an electrically noisy environment. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.

OPERATION INSTRUCTIONS

3.1 Control panel

3.2 Menu Map

motor
Range calibration| Pan/Tilt/Focus/Dimmer Range
XY Sp calibration| to set Pan/Tilt speed
Fan sp calibration| to set fan speed
Lamp_hours_clear| OK/CANCEL

3.2 DMX channels
The moving head can be operated in 2 DMX modes: SIMPLE (16ch) or EXPAND (20ch).

SIMPLE 16CH

| 1| COLOUR| select COLOURs, see details in COLOUR table
2| STROBE| select strobe effects, see details in DIMMER & STROBE table
3| DIMMER| select strobe effects, see details in DIMMER & STROBE table
4| GOBO| select gobo, see details in GOBO table
5| PRISM| select prism effect, see details in EFFECT table
6| PRISM ROTATION| select prism rotation, see details in EFFECT table
7| NONE|
8| FROST| select frost effect, see details in EFFECT table
9| FOCUS| focus adjustment from far to near
10| PAN| Pan movement, see details in Pan/Tilt Table
11| PAN FINE| Fine control of Pan, see details in Pan/Tilt Table
12| TILT| Tilt movement, see details in Pan/Tilt Table
13| TILT FINE| Fine control of Tilt, see details in Pan/Tilt Table
14| P/T SPEED| set Pan/Tilt movement speed, see details in Pan/Tilt Table
15| RESET| reset the moving head, see details in Reset & Lamp Table
16| LAMP| turn lamp on/off, see details in Reset & Lamp Table
EXPAND 20CH| 17| GOBO SPEED| set gobo wheel speed, see details in EXPAND CHANNEL Table
18| COLOUR SPEED| set COLOUR wheel speed, see details in EXPAND CHANNEL Table
19| FOCUS SPEED| set focus speed, see details in EXPAND CHANNEL Table
20| RUN MODE| set running mode, see details in EXPAND CHANNEL Table

PAN/TILT

DIMMER & STROBE

**** 2

| **** STROBE| 0-3| Strobe close
4-103| strobe from slow to fast(mode 1)
104-107| Strobe open
108-207| strobe from slow to fast(mode 2)
208-212| Strobe open
213-225| Random strobe, slow
226-238| Random strobe, medium
239-251| Random strobe, fast
252-255| Strobe open
3| DIMMER| 0-255| Dimmer 0 – 100%

COLOURS

1

|

COLOUR

| 0-4| White
5-9| White + Colour 1
10-14| Colour 1
15-19| Colour 1 + Colour 2
20-24| Colour 2
25-29| Colour 2 + Colour 3
30-34| Colour 3
35-39| Colour 3 + Colour 4
40-44| Colour 4
45-49| Colour 4 + Colour 5
50-54| Colour 5
55-59| Colour 5 + Colour 6
60-64| Colour 6
65-69| Colour 6+ Colour 7
70-74| Colour 7
75-79| Colour 7 + Colour 8
80-84| Colour 8
85-89| Colour 8 + Colour 9
90-94| Colour 9
95-99| Colour 9 + Colour 10
100-104| Colour 10
105-109| Colour 10 + Colour 11
110-114| Colour 11
115-119| Colour 11 + Colour 12
120-124| Colour 12
125-129| Colour 12 + Colour 13
130-134| Colour 13
135-139| Colour 13 + Colour 14
140-144| Colour 14
145-149| Colour 14 + White
150-199| Clockwise colour scroll
200-255| Counter-clockwise colour scroll

GOBOS

4

| ****

GOBO

| 0-4| Open
5-9| Gobo 1
10-14| Gobo 2
15-19| Gobo 3
20-24| Gobo 4
25-29| Gobo 5
30-34| Gobo 6
35-39| Gobo 7
40-44| Gobo 8
45-49| Gobo 9
50-54| Gobo 10
55-59| Gobo 11
60-64| Gobo 12
65-69| Gobo 13
70-74| Gobo 14
75-79| Gobo 15
80-84| Gobo 16
85-89| Gobo 17
90-129| Clockwise gobo scroll from fast to slow
130-134| Stop
135-169| Counter-clockwise gobo scroll from slow to fast
170-174| Gobo 1 shaking from slow to fast
175-179| Gobo 2 shaking from slow to fast
180-184| Gobo 3 shaking from slow to fast
185-189| Gobo 4 shaking from slow to fast
190-194| Gobo 5 shaking from slow to fast
195-199| Gobo 6 shaking from slow to fast
200-204| Gobo 7 shaking from slow to fast
205-209| Gobo 8 shaking from slow to fast
210-214| Gobo 9 shaking from slow to fast
215-219| Gobo 10 shaking from slow to fast

4

| ****

GOBO

| 220-224| Gobo 11 shaking from slow to fast
---|---|---|---
225-229| Gobo 12 shaking from slow to fast
230-234| Gobo 13 shaking from slow to fast
235-239| Gobo 14 shaking from slow to fast
240-244| Gobo 15 shaking from slow to fast
245-249| Gobo 16 shaking from slow to fast
250-255| Gobo 17 shaking from slow to fast

EFFECT

5

| ****

PRISM

| 0-127| No function
128-255| 8-facet prism

6

| ****

PRISM ROTATION

| 0-127| Angle 0 – 400°
128-191| Counter-clockwise rotation from fast to slow
192-255| Clockwise rotation from slow to fast
8| FROST| 0-255| Frost 0 – 100%
9| FOCUS| 0-255| Focus from far to near

RESET & LAMP

15

| ****

RESET

| 0-127| No function
128-200| Reset （over 3 seconds）
201-255| No function

16

| ****

LAMP

| 0 – 9| No function
10-100| Turn lamp on （over 3 seconds）
101-255| Turn lamp off （over 3 seconds）

EXPAND CHANNELS

20

| ****

RUN MODE

| 0 – 049| DMX mode
050-099| Pan Auto
100-149| Tilt Auto
150-199| Auto mode
200-255| Sound mode

General Maintenance

4.1 Fuse Replacement
a. Unscrew the fuse holder and remove the damaged fuse.
b. Replace with the same type fuse (F7A/250V) and screw fuse holder back in its place.
4.2 Cleaning
Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life. We recommend frequent cleaning of the fixture. When cleaning, please use a moist, lint-free cloth. Never use alcohol or solvents.
4.3 Lamp replacement
The moving head is equipped with an Osram 230W lam. Follow the procedure below to safely change the lamp.

1. Turn off the product and disconnect it from power. Wait at least 15 minutes for lamp to cool down.
2. Use 1/4 turn screw driver to remove 2 head covers. See Figure 1.
3. Remove the fan that blows out (not the other one) by 2 screws to access the lamp. See Figure 2-3.
4. Push the lamp reflector downward meanwhile grasp the lamp base to pull it out.
5. Remove the 2 wires connected to the lamp by the spade connectors.
6. Reverse the steps above to install the new lamp.

Warning! DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb or on the contacts that could reduce the lamp’s life.
Caution! Always disconnect the product from mains power and allow it to cool down before any services.
IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that old appliances contain and reduce the impact on human health and the environment, ensure that this product is recycled at the end of its life.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>