FENIX LR40R Super Bright Spot Searching Flashlight User Manual

**FENIX LR40R Super Bright Spot Searching Flashlight

**

FEATURES

• 15000 LUMENS MAXIMUM OUTPUT
• 900 METERS MAX BEAM DISTANCE

WARNING

• Do place this light out of the reach of children!
• Do NOT shine the light directly into the eyes of anyone!
• Do NOT shine flammable objects at close range, to avoid burning objects or causing danger due to high temperature!
• Do NOT use the light in inappropriate ways such as biting in the mouth, to avoid personal injury or life threats when the light or internal battery fails!
• This light will accumulate a lot of heat while working, resulting in a high temperature of the flashlight shell. Pay attention to safe use to avoid scalding.
• Turn off and lock the light or remove the battery from the light to prevent accidental activation when the light is placed in a closed and flammable environment such as pockets and backpacks!
• The LED of this flashlight is not replaceable; so the whole light should be replaced when the LED reaches the end of its life.

(ENGLISH) FENIX LR4OR V2.0 FLASHLIGHT

• Max 15000 lumens output and 900 meters ultra-long beam distance.
• Luminus SFT70 LED and sixteen Lumileds HL2X LEDs.
• Powered by battery pack that consists of 3 built-in 5000mAh batteries. .
• Compact body size for one-palm grip and convenient carry.
• Rotary toggle switch and an electronic switch for easy operation.
• Spotlight, floodlight and combined light modes to cover multiple lighting needs.
• Intelligent brightness downshifting sensor to avoid high temperature at close-range lighting.
• USB Type-C fast charging interface and USB Type-A discharging interface.
• Premium type HAIII hard-anodized anti-abrasive finish.
• Made of A6061-T6 aluminum. 0i Size: 6.89″ x 3.23″ x 2.17″ (175 x 82 x 55 mm).
• Weight: 29.7 oz / 842.5 grams (including battery).

OPERATING INSTRUCTION

On/Off
With the the light locked, rotate the toggle switch to any mode to turn on the light. With the the light switched on, rotate the toggle switch to lock mode to turn off the light. With the the light unlocked, press and hold the electronic switch for 0.5 s to turn on/off the light.
Mode Switching
Mode A is spotlight mode, mode B is floodlight mode, mode C is spot- and floodlight, mode D is flash mode. With the the light switched on and locked, rotate the toggle switch in clockwise to cycle through OFF/lock—miode A—mode B—mode C. With the light switched on and unlocked, press and hold the electronic switch for 1.2 s to enter mode D(defaults to Turbo), and press and hold the electronic switch for 1.2 s again to return to the last selected output.
Output Selection
With the the light switched on and unlocked(including flash mode), single click the electronic switch to select output.
Mode A: single click the switch to cycle through Eco—,Low—Med—,High.
Mode B: single click the switch to cycle through Eco—Low—Med—,High—.Turbo.
Mode C: single click the switch to cycle through Eco—,Low—>Med—,High—Jurbo.
Mode D: single click the switch to cycle through Strobe—,SOS—,return to last selected output.

Intelligent Memory Circuit

1. Turn on/off by toggle switch: mode A will be activated on Low each time it is turned on, mode B and C will automatically memorize the last selected output.
2. Turn on/off by electronic switch: the light memorizes the last selected output. When turned on again the previously used output will be recalled. Note: mode D wil be activated on Turbo each time it is turned on.

INTELLIGENT BRIGHTNESS DOWNSHIFTING SENSOR

On/Off On:
With the light unlocked, press and hold the electronic switch for over 10 s, the light will flash twice at the Low output of mode A, indicating the sensor function is abled. Off: With the light unlocked, press and hold the electronic switch for over 10 s, the light will flash eight times at the Low output of mode A, indicating the sensor function is disabled.
Intelligent Brightness Downshifting Sensor
The flashlight has a built-in intelligent sensing circuit. When the light surface is close to the lighting object (about 60mm) for more than 1.5 s, the flashlight will automatically downshift the output level to Low output of mode A to avoid danger caused by high temperature. When the light surface is more than 0.8 s away from the lighting object, the flashlight automatically recalls the previously used output level.

CHARGING

1. First switch off the light and open the anti-dust cap, plug the USB Type-C socket of the charging cable into the light, then connect the other end of the charging cable into the included adapter.
2. When charging, the charging indicators will flash from left to right to display charging status. The five indicators will be constant-on after charging is complete. 3. Be sure to close the anti-dust cover once charging is completed.

POWER BANK FUNCTION

1. Switch off the light and open the anti-dust cap and insert the USB Type-A socket of the charging cable into the USB discharging port of flashlight, then connect the other USB Type-C socket of the charging cable to the digital device with an USB Type-C port.
2. Single click the electronic switch to begin discharging, the indicators will recede from right to left to display the status.
3. Be sure to close the anti-dust cover once charging is completed.

Note:

1. The light can only be turned on at 100 lumens when charging.
2. The light and the included charging cable support 0C2.0. PD2.0 fast charging protocols. The normal charging time is approximately 4 hours from depletion to full charging.
3. All modes are available when discharging.
4. If the voltage is too low, the light will stop discharging.

BATTERY LEVEL INDICATION

With the light switched on/off(including locked status), single click the electronic switch to check the battery level and indicators will last for 3 s. Single click the electronic switch again in 3 s to close the indicators. Five blue lights on : 100%-80% Four blue lights on : 80%-60% Three blue lights on : 60%-40% Two blue lights on: 40%-20% One blue light on : 20% – 1%

TECHNICAL PARAMETERS

ANSI/ PLATO FL1| SPOTLIGHT MODE| FLOODLIGHT MODE| SPOT- AND FLOODLIGHT MODE| FLASH MODE
---|---|---|---|---
HIGH| MED| LOW| ECO| TURBO| HIGH| MED| LOW| ECO| TURBO| HIGH| MED| LOW| ECO| STROBE| SOS
OUTPUT
| 3000
lumens| 1500
lumens| 500
lumens| 10
lumens| 12000
lumens| 8000
lumens| 3000
lumens| 1000
lumens| 100
lumens| 15000
lumens| 10000
lumens| 5000
lumens| 1500
lumens| 300
lumens| 15000
lumens| 500
lumens
RUNTIME
| 3 hours| 3 hours
40 minutes| 14 hours
10 minutes| /| 2 hours
30 minutes| 2 hours
30 minutes| 3 hours| 11
hours| 50
hours| 2 hours
30 minutes| 2 hours
30 minutes| 2 hours
40 minutes| 6
hours| 25
hours| /| /
DISTANCE
| 900
meters| 650
meters| 380
meters| 60
meters| 340
meters| 280
meters| 170
meters| 100
meters| 30
meters| 900
meters| 780
meters| 600
meters| 400
meters| 250
meters| /| /
INTENSITY
| 196464
candela| 106416
candela| 35272
candela| 812
candela| 28189
candela| 19580
candela| 7264
candela| 2385
candela| 251
candela| 203568
candela| 153188
candela| 87344
candela| 37501 candela| 15153
candela| /| /
IMPACT RESISTANCE
| 1 meter
SUBMERSIBLE
| IP68

Note: The above specifications are from the results produced by Fenix through its laboratory testing using the battery pack that consists of 3 built-in 5000mAh batteries, under the temperature of 21±3°C and humidity of 50% – 80%. The true performance of this product may vary according to different working environments and the actual battery status. *The Turbo output is measured in total of runtime including output at reduced levels due to temperature or protection mechanism in the design.

PRODUCT OVERVIEW AND DIMENSIONS

INTELLIGENT OVERHEAT PROTECTION

The flashlight will accumulate a lot of heat when used on High mode for extended periods. When the light reaches a temperature of 60°C or above, the light will automatically step down a few lumens to reduce the temperature. When the temperature drops below 60°C, it will then allow the user the reselection of High mode.

LOW-VOLTAGE WARNING

When the voltage level drops below the preset level, the flashlight is programmed to downshift to a lower brightness level until Eco output is reached. When this happens in Eco output mode, one battery level indicator blinks to remind you to timely recharge the battery until it is completely power off.

USAGE AND MAINTENANCE

Disassembling the sealed head can cause damage to the light and will void the warranty. ©Rotate the toggle switch in anticlockwise direction to lock the flashlight to avoid accidental activation. ©Long-term use can result in 0-ring wear. To maintain a proper water seal, replace the ring with an approved spare. ©Periodic cleaning of the battery contacts improves the lamp’s performance as dirty contacts may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following reasons: A: Poor battery level. Solution: Recharge the battery. B: The product, battery contact or other contacts are dirty. Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol.
If the above methods don’t work, please contact your authorized distributor.

INCLUDED

LR4OR V2.0 flashlight, Type-C charging cable, Lanyard, Holster, Spare 0-ring, User manual, Warranty card.

LIGHTING FOR EXTREMES

• FACEBOOK
  

• WECHAT
  
  “Follow” us for more information about Fenix.

FENIXLIGHT LIMITED

Tel: +86-755-29631163/83/93
Fax: +86-755-29631181
E-mail: info@fenixlight.com
Web: www.fenixlight.com
Address: 2F/3F, West of Building A, Xinghong Technology Park, 111 Shuiku Road, Fenghuanggang Community, Xixiang Street, Bao’an District, Shenzhen City, Guangdong Province, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>