Hisense WTJA1101T Top Load Washer Instruction Manual

: June 12, 2024
: Hisense

Table of Contents

WTJA1101T Top Load Washer
Product Information
Usage Instructions

WTJA1101T Top Load Washer

Product Information

The product is a washing machine with the model number WTJA1101T
and the serial number 2216642-X08061060B. It weighs 10.5kg and has
a water pressure requirement of 0.03 MPa to 0.8 MPa. The dimensions
of the washing machine are 550mm x 604mm x 969mm.

Usage Instructions

Connection of Water Hose and Washing Machine

Push slider down to remove hose joint from water inlet
assembly, as shown in Fig.
Loosen 4 screws on hose joint properly and then connect hose
joint to tap, as hose unavailable, loosen 4 screws and remove bush,
as shown in Fig..
Tighten 4 screws on hose joint evenly, as shown in Fig..
Tighten nuts as shown in Fig.. Note: length of exposed thread
before and after tightening of fastening nuts shall change from 4mm
to 2mm approximately.
Connect water hose nuts to inlet valve head, tighten nuts and
slightly shake to check if they are secured.
Check the connection of hose joint and water hose.
To remove water hose, close the tap and press down the slider
to remove the water hose.

Usage of the Drain Hose

The drain port should not be more than 10cm above the ground,
otherwise drainage would not work, drainage time would be too long
or drainage would stop at midway.
Do not tread on or squeeze the drain hose.
Cut one part of the drain hose when it is too long. For smooth
drainage, cut the front end of drain hose at an angle.
Purchase another section of hose at proper position if extended
hose is too long.

Power Switch and Start/Pause Button

Press the power switch to turn on the power.
After power-on, press the power switch to turn off the
power.
Press the Start/Pause button to start the washing machine.
While the washing machine is running, press the Start/Pause
button to stop it.

Options Button

Press the Options button repeatedly to cycle through the Air
Dry and Extra Soft options.
Select Air dry function to air dry the clothes.
Select Extra Soft function to run one more rinse before the
last rinse which flushed the softener to reduce the influence of
detergent on the softness of clothes.
No matter whether Extra Soft has been selected or not, the
softener will be flushed in the last rinse.
The Extra Soft function cannot be selected without rinsing
process.

WTJA1101T
2216642-X08061060B

T

0.03
10.5kg.
WTJA1101T 10.5
0.03 450 39
550X604X969

50

Appropriate tap

water pressure from 0.03 MPa to 0.8 MPa.

Outlet end face

,PSURSHUWDS

1 0mm

Length of front end must be greater than 10mm. 2XWOHWHQGIDFHRIWDSVKDOOEHÀDW,IQRWÀDWWHQLWZLWKD¿OHWRDYRLGOHDNDJH

1.Push slider down to remove hose joint from water inlet assembly, as shown in Fig. .
2.Loosen 4 screws on hose joint properly and then connect hose joint to tap, as hose
unavailable, loosen 4 screws and remove bush, as shown in Fig.. Front

Hose joint

Slider Water inlet hose
1

Screw

Screwdriver
2

Bush
3

3.Tighten 4 screws on hose joint evenly, as shown in Fig.. 4.Tighten nuts as shown in Fig..
Note: length of exposed thread before and after tightening of fastening nuts shall change from 4mm to 2mm approximately.

Before tightening, about 4mm
After tightening, less than 2mm

Nuts

4

5

6

Connection of water hose and washing machine

Connect water hose nuts to inlet valve head, tighten nuts and slightly shake to check if they

Water hose nuts Inlet valve head

Notice 1.Tighten evenly and do not twist water hose,
otherwise hose joint would be damaged.
2.Do not remove absorbing pad. Check if it falls off or has been damaged every time washing machine is going to be used. If yes, contact Hisense service department immediately.

Absorbing pad

Connection of hose joint and water hose
Press down slider and insert water hose into joint. Then release the slider.

Water hose joint. Slider

Check connection of hose joint and water hose
1.After connection, open tap to check if there is any leakage. 2.Gently pull water hose to check if it is secured. 3.Do not bend water hose forcibly. 4.Before every use, check if the water hose
connection and the connection of hose joint and tap are secured, in order to prevent disconnection caused by improper mounting.

Remove water hose
1.Close tap. 2.Press down the slider to remove the water
hose. If the washing machine would be used once or more times in a week, do not remove the hose joint to prevent the set screws from being damaged.

Slider

10

Usage of the drain hose

Drain hose shall operate smoothly

1.Drain port shall not be more than10cm above the ground, otherwise drainage would not work, drainage time would be too long or drainage would stop at midway.

4.Purchase another section of
when extension is necessary.
30mm

2.Do not tread on or squeeze the drain hose. 1.

10cm

3.Cut one part of the drain hose when it

hose at proper

is too long. For smooth drainage,

position if extended hose is

cut front end of drain hose at an angle. too long.

AB

101

10.5
the /
/ t

8.0 10.5

1.5-2.0

10 9

8.0

1.5

70

91g

65

84.5g

60

78g

55

71.5g

50

65g

45

58.5g

40

52g

35

45.5g

30

39g

25

32.5g

12

13

1. Power switch Press the power switch to turn on the power. After power-on, press the power switch to turn off the power. If the “Start/Pause” button is not pressed in 10 minutes after the power is turned on, the washing machine will automatically power off .
2. Start/Pause
After power-on, press this button to start the washing machine. While the washing machine is running, press this button to stop it.

3. Options Press Options button repeatedly to cycle through the Air Dry and Extra Soft Select Air dry function,Air dry the clothes Select Extra Soft function, WM will automatically run one more rinse before the last rinse which flushed the softener to reduce the influence of detergent on the softness of clothes.No matter whether Extra Soft has been selected or not, the softener will be flushed in the last rinse.The Extra Soft function cannot be selected without rinsing process.

4. Program

Choose the appropriate washing program based on the load,

texture and dirtiness of laundry.

The selection sequence is as follows: Fuzzy

Quick

14

5. Delay

The Delay time is within 24 hours. When the Delay is set, the

when

the automatic process programming is performed again.

After the Delay is started, the ongoing process and automatic time

programming of Delay time can be stopped. During pause, the

Delay

rinse

function

and remaining time are showed; when the Delay time is changed,

the new Delay time is displayed; when the “Start/Pause” button is

pressed, the program controller will automatically adjust the Delay

time according to the currently required total time.

Press Deley for 3 seconds,washer is mute.

Depending on the load of laundry to be washed, press this button
Water replenishing: After the program is started, press the “Water And
The water replenishing is suitable for the soak, wash and rinse
replenishing is automatically stopped. In addition, no water replenishing is allowed during the fuzzy run. Under child lock state, the manual water replenishing is prohibited.

7. Soak Press Wash for 3 seconds,the soak process is started. Soak or not is determined according to the dirtiness of laundry. In quick programs, the soak process cannot be started.

8. Child lock After the program is started, press the “Rinse” and “Spin” buttons simultaneously for 3 seconds to set or cancel the child lock. After the child lock is started, all the buttons on the panel are in and the child lock is automatically canceled after the program finishes.

15

Under the child lock state, if the cover is opened, the “E1” alarm will be issued, then if the cover is not covered within 5 seconds, the washing machine will automatically drain, and stop the drainage after the alarm is removed. After the power is turned off, the child lock is invalid.

9. Wash

The washing time can be adjusted according to the needs of the

user.

When the “Wash” button is pressed for a long time, the figure on

the digital tube is incremented continuously until the button is

released.

The washing time for quick program is no more than minutes.

The washing time for

is no more than 20 minutes. After

powering on the machine or selecting the program, press the

“Wash” button to select the single wash program. At this time, the

digital tube displays the currently required washing time; press

the “Wash” button again to increment the washing time in cycle,

and the washing time cannot be set to 0. After selecting the

single washing program, press the “Rinse” button to add the

rinsing process, and press the “Spin” button to add the spin

process.

10. Rinse The default time of rinses is as follows: When the quick program is selected, the default time of rinse is 1; when the programs of fuzzy, delicate, jeans, heavy or eco are selected, the time is 2; and when the baby care is selected, the time is 3. If only rinse program is set by the user, the time of rinse cannot be set to 0.

11. Spin The spin time can be selected. The single spin can be set. After powering on the machine or selecting the program, press the “Spin” button to select the single spin program. Meanwhile, the spin time cannot be set to 0.

12 .Power-failure memory function In case of power failure during drainage or water intake, the initial time of drainage or water intake will be backed to after power-on. In case of power failure during presetting, soaking or washing, the latest time point memorized will be backed to after power-on. In case of power failure during rinsing, the initial time point of rinsing will be backed to after power-on. In case of power failure during spinning, the initial time point of spinning will be backed to after power-on. The standby, pause and warning process will not be memorized.

16

Wash

program time(min)

F uzzy

13

2

Jeans

19

2

Quick

5

1