YOLINK YS7805-UC Outdoor Motion Sensor User Guide
- June 12, 2024
- YOLINK
Table of Contents
YOLINK YS7805-UC Outdoor Motion Sensor
Product Information
The YoLink Outdoor Motion Sensor is a smart home device that connects to the internet via a YoLink hub. It comes with 2 AA non-rechargeable batteries (installed) and can be mounted using the included mounting plate and Phillips screws. The sensor has a detection window, a SET button, a status LED, and an axis for adjusting the sensor’s position for optimal detection area. The LED on the sensor blinks in different colors to indicate various device statuses.
Product Usage Instructions
- Download the full Installation & User Guide by scanning the provided QR code or visiting the YoLink product support page.
- Make sure you have all the required items, including a Phillips screwdriver, drill & bits, and special anchors if necessary.
- Turn on the Outdoor Motion Sensor by briefly pressing the SET button until you see the LED flash red and then green.
- If you are new to YoLink, install the YoLink app on your smartphone or tablet from the appropriate app store. If you already have the app installed, proceed to the next section.
- Follow the app’s instructions to add the Outdoor Motion Sensor to your YoLink network. Make sure your YoLink hub is installed and online before attempting to connect the sensor.
- Mount the sensor using the included mounting plate and Phillips screws. Adjust the sensor’s position for optimal detection area using the axis.
- The LED on the sensor will blink in different colors to indicate various device statuses, such as device start-up, restoring to factory default settings, connecting to the cloud, updating, and low battery status. Refer to the product manual for a complete list of LED behaviors and their meanings.
Welcome
Thank you for purchasing YoLink products! We appreciate you trusting YoLink
for your smart home & automation needs. Your 100% satisfaction is our goal. If
you experience any problems with your installation, with our products or if
you have any questions that this manual does not answer, please contact us
right away. See the Contact Us section for more info.
Thank you! Eric Vanzo Customer Experience Manager
The following icons are used in this guide to convey specific types of
information: Very important information (can save you time!)
Before You Begin
Please note: this is a quick start guide, intended to get you started on the installation of your Outdoor Motion Sensor. Download the full Installation & User Guide by scanning this QR code:
Installation & User Guide
You can also find all guides and additional
resources, such as videos and troubleshooting instructions, Outdoor Motion
Sensor Product Support Page by scanning the QR code below or by visiting:
https://shop.yosmart.com/pages/ outdoor-motion-sensor-product-support
Product Support Support produit Soporte de producto
Your Outdoor Motion Sensor connects
to the internet via a YoLink hub (Speaker- Hub or the original YoLink Hub),
and itdoes not connect directly to your WiFi or local network. In order for
remoteaccess to the device from the app, and for full functionality, a hub is
required. This guide assumes the YoLink app has been installed on your
smartphone, and a YoLink hub is installed and online (or your location,
apartment, condo, etcetera, is already served by a YoLink wireless network).
In the Kit
Required Items
You may require these items:
Get to Know Your Outdoor Motion Sensor
Battery Compartment: Includes two AA non-rechargeable batteries ****
Get to Know Your Outdoor Motion Sensor, Cont.
LED Behaviors
-
Blinking Red Once, then Green Once
Device Start Up -
Blinking Red And Green Alternately
Restoring to Factory Default Settings -
Blinking Green
Connecting to the Cloud -
Fast Blinking Green
Control-D2D Pairing in Progress -
Slow Blinking Green
Updating -
Blinking Red Once Device is Connected to the
Cloud and is Functioning Normally -
Fast Blinking Red
Control-D2D Unpairing in Progress -
Fast Blinking Red Every 30 Seconds
Batteries Are Low; Replace the Batteries
Power Up
Turn on the Outdoor Motion Sensor by briefly pressing the SET button, until you see the LED flash red then green. ****
Install the App
If you are new to YoLink, please install the app on your phone or tablet, if
you have not already. Otherwise, please proceed to the next section. Scan the
appropriate QR code below or find the “YoLink app” on the appropriate app
store.
- Apple phone/tablet iOS 9.0 or higher
- Android phone or tablet 4.4 or higher
Open the app and tap Sign up for an account. You will be required to provide a username and a password. Follow the instructions, to set up a new account. Allow notifications, when prompted. You will immediately receive a welcome email from no-reply@yosmart.com with some helpful information. Please mark the yosmart.com domain as safe, to ensure you receive important messages in the future. Log in to the app using your new username and password. The app opens to the Favorite screen. This is where your favorite devices and scenes will be shown. You can organize your devices by room, in the Rooms screen, later.
Add Your Motion Sensor to the App
- Tap Add Device (if shown) or tap the scanner icon:
Add Your Motion Sensor to the App, Cont.
- Approve access to your phone’s camera, if requested. A viewfinder will be shown on the app.
- Hold the phone over the QR code so that the code appears in the viewfinder. If successful, the Add Device screen will be displayed.
- Follow the instructions to add your Outdoor Motion Sensor to the app.
Installation
Sensor Placement Considerations:
- Depending on the location, the height and/or distance from your intended motion-detection area, it may be possible that your outdoor motion sensor responds slower than desired or too soon. Experiment with several locations until the sensor responds as desired.
- The outdoor motion sensor responds best to motion across the coverage area, as opposed to directly towards the outdoor motion sensor. As your sensor utilizes heat detection technology, avoid
- locations subject to rapid temperature changes, direct sunlight, or near heat sources such as heating registers, vents, radiators, space heaters, fireplaces, etc. All these environmental factors may cause false alarm and/or damage to the PIR sensor. Avoid sensor locations where it can be easily touched, such as by a child or dog.
Installation, Cont.
- We recommend mounting the motion sensor on a sturdy, non-metal surface, like a wall or a wooden post or a tree
- Detection Angle: The optimal detection angle is across the direction of motion, or 90°, similar to a gate across your driveway, as shown right
Avoid directing the sensor near surrounding areas with movement or activity (such as a nearby road that may cause false alerts. Factors such as temperature can adversely impact the optimal range and performance of the sensor.
Mounting Methods:
- A: With the plate vertical to the floor or ground
- B: With the plate horizontal to the floor or ground
Test the Outdoor Motion Sensor Location Before Installation:
- Test your outdoor motion sensor location before affixing the plate to the surface. Use masking or painters tape to secure the sensor to the surface, being careful to not obscure the detection window. Once you have the sensor temporarily mounted, test it out. With the app in hand, walk into the intended detection area while observing the status of the sensor as shown on the app (Motion Detected or No Motion Detected). Optionally, you may set up your automation (e.g. turn on a light on motion detection) to functionally test the motionproceed to the following steps for information on creating automations, then return to this step.
Begin Installation:
- Mark an outline (with a pencil, tape, etc.) of the mounting plate on the mounting surface for future reference after testing. Ensure the arrow on the plate points upward.
- Mount the plate with three of the four screws. Do not over-tighten the screws.
Method A Installation:
- Adjust the angle of your sensor so that it is viewing the target area.
- Tighten the adjustable bracket screw securely using a phillips screwdriver.
- Secure the mounting plate to the surface with the fourth screw.
- Gently tug on the sensor, to ensure it is rigid and secure.
Method B Installation:
- Gently turn over the sensor so that the fourth screw hole is visible. Insert and tighten a screw in this hole.
- Adjust the angle of your sensor so that it is viewing the target area.
- Tighten the screw securely using a phillips screwdriver.
- Gently tug on the sensor, to ensure it is rigid and secure.
Test the Outdoor Motion Sensor:
- Test the sensor. It is very important that you test the sensor as realistically as possible, to ensure it works as required for your application. With your phone in-hand, using the app, refer to the Outdoor Motion Sensor’s status as you walk through the coverage area. You may need to adjust the position or location and/or the sensitivity. Motion sensitivity can be set in the app.
Refer to the full Installation & User Guide and/or the online resources for additional information and to complete the set-up and settings for your Outdoor Motion Sensor.
Contact Us
- We are here for you, if you ever need anyassistance installing, setting up or using a YoLink app or product!
- Need help? For fastest service, please email us 24/7 at service@yosmart.com.
- Or call us at831-292-4831 (US phone support hours: Monday – Friday, 9AM to 5PM Pacific)
- You can also find additional support and ways to contact us at: www.yosmart.com/support-and-service.
- Or scan the QR code:
- Support Home Page
- Finally, if you have any feedback or suggestions for us, please email us at feedback@yosmart.com.
- Thank you for trusting YoLink!
- Eric Vanzo
- Customer Experience Manager
- 15375 Barranca Parkway
- Ste. J-107 | Irvine, California 92618
- © 2023 YOSMART, INC IRVINE,
- Avoid directing the sensor near CALIFORNIA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>